similar to: Transferring Using Flash

I was alerted the other day by of all people, my mom, that she wasn't hearing a "ring" when she dialed my number. Puzzled, I tried calling myself. The call connects, but there's dead silence until voicemail picks up. Calling internally, extensions worked perfectly. So, I figured, "another damned Broadvoice issue." For kicks, I upgraded to 1.2.6 today, and the end

We have recently pulled an ancient Fujitsu-branded Centigram voicemail system out of production use and replaced it with an Asterisk box, which is now serving as our enterprise voicemail system and automated attendant. The Asterisk system is connected to a Fujitsu F9600 PBX and uses the 1.6.1.x SMDI module to communicate between the two systems. Save for one issue, the replacement of the old

I've tried to transfer a call using the Flash command, but with my configuration it doesn't work. I have a traditional PBX connected with a zap channel to Asterisk that acts like an IVR: TELCO line --> traditional PBX (FXS) --> (FXO) Asterisk >From the TELCO line I can make a call to the traditional PBX and reach Asterisk, the IVR system on Asterisk answers the call and I can

Problem: Flash on X100P does not flash. Phone line has Call Transfer. With this line plugged into a regular phone, it can receive a phone call. Then, depress the hook momentarily, release. Dialtone is now available. Dial a different number. Call is answered. Hook Flash again, now in a three way call. Hang up. The other two parties are still in communication. Now, plug same line into the X100P.

List, Having a little trouble with the following. Let me prefix by saying I have blind transfers working from the following setup. Inbound call [from-zap] (SIP/sv0071iv) answers. Zaptel -> Asterisk -> SIP extension SIP extension then blind transfers [from-sip] --- SIP extension -> Asterisk -> Zaptel During this whole process, the original channel off the trunk (lineside T1) is

I am working with the telantek.adsi file, and I was wondering how I would create a softkey for Transfer. I tried making a key definition and using SENDDTMF "#", but that didn't work. Is there another way I could do this? Also, does anybody have any ADSI scripts for use with Asterisk that they would like to share? Thank you for your time. __________________________________ Do you

I have a TDM2402E card. Occasionally I have noticed that a number I call that gives and IVR the DTMF keys are not detected. All other times the DTMF works fine. /proc/interrupts is: CPU0 CPU1 0: 500798020 500749281 IO-APIC-edge timer 8: 4 9 IO-APIC-edge rtc 9: 0 0 IO-APIC-level acpi 15: 4505912 4502264 IO-APIC-edge

I have a dialplan that requires that we use * to send the long distance access code to AT&T. I have found in the list that the `w` command can be used to inject a pause, I have tried the following: exten => _91NXXXXXXXXX,1,Dial(ZAP/g1/${EXTEN}www5555555,70) There `5555555` is the ld access code. I tried various quantities of `w`s but I never got * to dial the ld access code. Allof the

<DIV><FONT face=Arial size=2>hello All,</FONT></DIV> <DIV><FONT face=Arial size=2></FONT>&nbsp;</DIV> <DIV><FONT face=Arial size=2>our Asterisk pbx is sitting behind a normal analog hardware pbx, we have to dial 9</FONT></DIV> <DIV><FONT face=Arial size=2>to take an outside call through the hardware pbx, our

We're in the process of replacing an ancient Centigram-based, but Fujitsu-labelled, voicemail system with an Asterisk solution. The system will interface with a Fujitsu F9600 switch and use the SMDI module in Asterisk 1.6.1.x to communicate the calling information needed to make the interplay between the two systems work smoothly. This portion of the project is configured and working fine, as

Hey all, Wondering if this is possible.. Incoming call is answered through X100P, then an extension is dialed using the same X100P card. Basically I want to dial in, enter 9 + <phone#> and have it do a flash then have it dial *08 <the same phone number> + # on the same PSTN line to have it transfer my call to another phone number. I realize this isn't very safe, but I would

I've got a piece of CPE equipment that has an FXS port that I have tied to an FXO port on a TDM400 clone card. Normally, if I go off-hook with a standard telephone connected to it, I get a dialtone. If I dial a digit, and send a hookflash, the device will provide a dialtone back for the next available channel on the device. I'm trying to recreate this same behavior with Asterisk,

Hi, I believe the issues raised by this message are the same as mine, more on a commercial sense than for self use, but mostly the same. I've seen posts where real-life installations are mentioned, but not a reference to how Asterisk is working on production (and productive) environments. Any experiences would be very welcome I believe, not only on pure technical, but wider, sense. Thanks

Hi, everybody: As part of a paging macro I'm using SendDTMF to send digits to the called party. The section looks like this: exten => s,1,Wait(0.5) exten => s,n,SendDTMF(9531290) exten => s,n,Wait(1.0) exten => s,n,Set(MACRO_RESULT=CONTINUE) To test I direct the call to a live extension just to hear what's happening -- what actually happens is that only the 9 is sent, and

I managed to sort out my earlier query regarding flash times (changed delay in zapata.conf) Now, I am getting a timeout after the Flash command in an outgoing call-file based call: -- Attempting call on Zap/1/108 for 567112@demo:4 (Retry 1) > Channel Zap/1-1 was answered. -- Executing Festival("Zap/1-1", "Dialling now") in new stack == Parsing

Folks, For the last few days I've been trying to experiment with a Panasonic PBX and an X100P but have run into quite a few problems which I am not sure if they can be solved with this type of card (how about TDM01B?) 1) I wanted to use *'s IVR capabilities, so I routed the calls to the extension where the x100p was connected to. Asterisk should answer the call, playback a message,

Hi all, I've compiled samba 4 from branches and it worked like a charm. I'm trying to use regshell to read (remotely) the following Windows registry key: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Uninstall I can connect to the remote machine with no problems: ./regshell --remote=192.168.50.142 --user=Administrador%xxx HKEY_CLASSES_ROOT> HKEY_CLASSES_ROOT>

I have been trying to figure a way to SendDTMF into a MeetMe room using the Manager API. I can't redirect everyone into another context and then bring them back because that would mess up my logic. I am trying to use local channels and the originate Action to accomplish this. Exten: 3441115 Priority: 1 ActionID: actid-00000001 Context: senddtmftones Action: Originate Channel:

I was just trying to find a better way to transfer incoming calls to external phone numbers without tieing up my lines. The following has worked successfully for me and I just thought I'd post it so if someone was looking to do the same they could quite easily. The feature you need installed on your lines is called conference-drop-transfer or here in canada it's know as

Hello, I'm looking for a similar feature... Dial a number via ZAP/g1 after the line gets answered wait 10 seconds send DTMF Regards, Marc -- Network Manager Marc Storck LuxAdmin.Org mstorck@luxadmin.org Internet Service Provider http://www.luxadmin.org 15, route d'Esch Phone: +352 2727 3030 L-4544 Belvaux Fax: +352