similar to: Problem with calls starting from a legacy PBX

Hi, When we make an outgoing call on ISDN (zaphfc) with overlap dialing we get immidiate hangup after answer. But when we place a full number before dialing everything is ok. Any help appriciated!! Thanks here is info with debug: == Primary D-Channel on span 1 up -- Executing Dial("SIP/200-164c", "zap/g1/|100|tc") in new stack -- Making new call for cr 192 --

I have a PRI E1 link between Asterisk 1.4.24 and Alcatel-Lucent OmniPCX Enterprise R9.0. As EuroISDN it works fine. However, I need to move to QSIG because of a firmware upgrade on the Alcatel PBX which doesn't support EuroISDN (please don't ask why). Besides, I've read somewhere that 2 B Channel Transfers "should" work with * 1.4, the latest 1.4 libpri and QSIG. So this

Hello all, I have Asterisk 1.2.1 and a TE110P connected to a Nortel Meridian Option 81C system. The PRI line is currently setup as DMS100. Here are the relevant lines from zaptel.conf and zapata.conf: zaptel.conf: span=1,1,0,esf,b8zs bchan=1-23 dchan=24 loadzone = us defaultzone = us zapata.conf: [channels] language=en context=from-internal musiconhold=default switchtype=dms100

I have this setup: (PSTN E1 PRI) -- Asterisk -- (crosscable) -- Alcatel PBX --- analog phones and a few of VoIP phones directly connected to Asterisk. Calling a number (just one!) - an automatic responder (IVR) - from VoIP phones works, from analog phones doesn't work: NOANSWER after a few seconds. I'm using no 'r' in dial options (this caused a problem with an IVR some time

Is there a setting somewhere in * to define whether I am receiving callerID or true ANI? Global Crossing claims they are sending ANI but I dont think so. My understanding of ANI is that it is always sent, regardless if callerID is blocked. If I dial *67 and my DID, I get "Presentation: Presentation prohibited of network provided number" and no number. Before I call GC on Monday

Hi all, I tried to connect the bristuffed(0.3.0-PRE-1i) * to an Alcatel PBX via BRI (zaphfc) and Q.SIG. The Alcatel PBX is connected to the outside world and should forward our calls to the telco. This setup works correctly as far as I use euroisdn as the switchtype. The first problem was that it is only possible to run the * side in CPE-mode -- I wanted NET. Anyway, I configured * this way:

Hey all, I am running a Asterisk 1.2.9.1 with Sangoma A101 card, newest firmware, configured with a help from Sangoma Tech Support, running fine. It is connected to a PRI circuit split from Cisco MC 3810, which in turn is connected to a Converged T from CTC Communications. While Asterisk works fine and I can call in/out on my BV account, I am only able to dial in through CTC. I have spent

hello everyone, I have a trixbox server with an E1 card(not digium).It connects to an AVAYA pbx use E1. It works fine.But when i change the E1 card to digium TE220B,there is a problem. When sip extension A(on trixbox) call PSTN extension B(on avaya),A must wait longtime before B start to ring.From the log I find there are two times call. I don't know why the first request be rejected

Hi! For demonstration purposes I try to bridge an incoming video call from a 3G mobile handset to another 3G mobile handset using asterisk as "switch". On the incoming call leg I see all expected bearer capabilities (Digital, 64k Transparent, G.7xx 384k video) but on the outgoing call leg the bearer capability G.7xx 384k video get lost and therefore the call is dropped from the mobile

OK I am going to do it again. Global Crossing is now sending ANI but it is not in the format I expected. Any one know of a way to get this data into two seperate variables? The first number is ANI and the second is DNIS so it is "*tendigits*tendigits* on one line like below. < Called Number (len=26) [ Ext: 1 TON: National Number (2) NPI: ISDN/Telephony Numbering Plan

Hey all. We have a DS3 circuit with GBLX split off into 7 systems with a 4 port sangoma card (A104D) in the first 2 systems, and digium T410P cards in the other 5. GBLX numbers their spans from 0 to 3 instead of 1-4 and we have a NFAS configuration with the d-channel on chan 96. All of our systems are running 1.0.7 for stability reasons (and no good time for maintaince, the entire platform

We've got a EuroISDN (32 channels) with a TE405p, running cvs head as of 5 days ago. In the past couple of days, we've hit a scenario where incoming calls to the * pbx from the PSTN are being marked as busy, but outgoing calls work just fine. When we reboot *, the problem goes away. Has anyone else had this ? I've attached a PRI debug below. I've changed the phone numbers (x

Hello, Configuration: Asterisk CVS HEAD 20050730 on RH EL3+ DIGIUM TE110P PRI card + euroISDN E1 I am trying to sort out the problem: 1. Provider's switch sends "SETUP"; 2. Asterisk receives "SETUP", rings allocated extension but does not send "Setup acknowledge" (or any other messages) to switch; 3. After 4 seconds of waiting of *'s response switch sends

Hi. recently I have been trying to setup a PRI on asterisk. Inbound calls are working just fine but I am not able to make outbound calls. Does anyone know what I need to change to make outbound calls work? Right now the PRI is instantly hanging up on the outbound calls. I have included full debug info as well as config files. /etc/zaptel.conf span=1,1,1,esf,b8zs bchan=1-23 dchan=24

We've been working for the past 2 weeks to get a new V400P working with our PRIs from the telephone company. We're trying to get the Asterisk server setup as a VoIP gateway for SIP and AIX. We can make SIP-SIP calls, but all calls from or to the PRI fail. This is the applicable entries from the Asterisk log (configuration files follow) for a call coming from the PSTN on the PRI. I

Hi all, I'm trying to insert a Rhino Ceros box equipped with a Rhino R2T1 dual-T1 card and running the latest version of Trixbox (2.4.2) between the central office and a Nortel Option 11. The switch at the CO is a DMS100. Basically, I'm taking the T1, connecting it to port 0 on the R2T1 card, and then connecting port 1 to the Nortel. (Actually a CSU and then the Nortel) We're running

Hello! Is it possible to connect Siemens HiPath 4000 to Asterisk? What equipment required on Siemens side? I mean IP not E1. Sorry for asking here. Siemens-related websites use "salesperson language". There is no technical information.

Hi all, I have some problem to send a FAX to a given number. I use asterisk 1.2.18, on a openSUSE 10.2, i586 host. The FAX is sent out via an ISDN PRI interface, I'm in Germany, and the destination FAX devices are in Germany too, but in different areas, so I have to use a city prefix. I did set the pri device in debug mode, below are two calls, to two different FAX numbers, the first is

I have a server running Asterisk 1.4.14, Zaptel 1.4.6, Libpri-1.4.2 on a CentOS 5 server. The server has a single TE110 card connected to a provider called Alestra in Monterrey, Mexico. Since we installed everything we have been having problems dialing certain numbers, those numbers always fail when dialed from Asterisk but if you dial from your cell phone they always go through. I once has a

I have a T1 link from asterisk 1.2.23 (also tried with 1.4.13) to a Meridian Option 61C. Calls either way drop with error "Channel 0/23, span 1 got hangup, cause 100". Can anyone offer insight into the cause and solution/workaround? (I tried upgrading to Ast 1.4.13, and upgrading matching zaptel & libpri, put the problem is identical). For testing, I tried a call from the