similar to: IAXy Port number. Repost

The file used with a Digium IAXy device: "iax.conf" has the line: "port=5036" (I also use the "bindaddr=192.168.1.91" entry) but when Asterisk talks to the IAXy device it used port 4569 (from "tcpdump"). How are the port numbers assigned? What tells the IAXy which port to use. The IAXy provisioning file "iaxy.conf" file does not specify a port

I can't seem to get this device to grab an ip from dhcp. We have a working dhcp server (unfortunately it is on Windows), but I don't show any leases requested by the iaxy. Anyone have any ideas? The ethernet and phone lines are plugged in before the device is powered. Thanks, Erik

Hi, I've provisioned an IAXy adapter on a network segment local to my asterisk server. Provisioning is fine, as is the registration and use of said device. Since the local address is private address space, I setup the public IP address of my Asterisk server as the alternate. When taking it to another location (NAT again behind a WRT54G), it doesn't seem to work. Here's my current

Trying to configure IAX for use I think I have everything set right. But my IAX phone wont connect. When I run wireshark I'm seeing this Note if above screenshot from wireshark does not show here is a link for it: http://img402.imageshack.us/i/tempe.jpg/ I've tried a variety of setups in my IAX.conf (they all end up with the same issue, tried just bindaddr=0.0.0.0 with

According to my IAX-provider, an account has been created for me on their Asterisk-server... But the Asterisk CLI tells me this : asterisk*CLI> iax2 reload == Parsing '/etc/asterisk/iax.conf': Found [Apr 30 20:51:30] NOTICE[6391]: chan_iax2.c:10124 set_config: Ignoring bindport on reload [Apr 30 20:51:30] NOTICE[6391]: chan_iax2.c:10183 set_config: Ignoring bindaddr on reload

Hey Everyone, I recently purchased a few IAXy units for some testing, and have come across a some problems. One of them can be provisioned but will not ring the connected telephone. It also does not provide a dial tone when you pick up the phone. When a call is made to the IAXy one of the green lights on the board goes from a solid on state, to a flashing state that coincides with the

I'm going to try and lay out all the relevant information I have here in this one post. I can provide more info if necessary. ISSUE 1: Office A routinely looses connection to Office B. When typing IAX2 Show Peers, it will show as Unreachable. I issue IAX2 Reload and it will work again for 1-3 days (haven't narrowed the time down yet). My theory is that the DSL at Office2 is changing

I have a brand new IAXy I'm playing with. I do not get a dialtone on the phone, or any response at ll on the phone. No sound, no dialing, no ringing. The phone and wire are tested and known to be good. I think I have it setup correctly. When I give the iaxprov command I get this: #iaxyprov 192.168.1.90 iaxy.conf 02: c0 a8 01 5a 05: 11 d9 03: ff ff ff 00 04:

Hi, I am a newbie in asterisk. trying to configure firefly third party edition to connect to aserisk 1.0.3 im able to authenticate but cannot dial extensions. I have been reading the documentation cant seem to find the correct configs. Attached the error message and configs. What am I missing? *CLI> Urgent handler Feb 12 15:52:05 NOTICE[16537]: chan_iax2.c:5718 socket_read: Rejected connect

For anyone playing around with IAXy(S100i) devices, I am making the following available: Windows IAXy Provision v1.00 This is a from-the-ground-up development of a means of provisioning IAXy devices using a Windows environment. For some users, being bound to Linux for IAXy provisioning is not viable or convenient in some cases. This application provides a GUI data entry for the various IAXy

Our * box is behind NAT with 4569 forwarded to it. I'm using stable 1-0 version. We're pure VoIP. Our SIP phones can use * to dial out, and can receive incoming calls, and conference in another SIP. However, if we try to conference 2 IAX connections together, we'll get one-way audio for one of the connected IAX devices. I found that this also happens if I use an IAXy to call out from *

Hello all, In changing the phone connected to my IAXy I remembered that this phone will not ring on the standard frquency (20hz?) when connected to the FXS. There is a patch, one line to change in wcfxs.c for use with a TDM400P, but obviously this doesn't change the FXS on the IAXy. Is there any possibiity of a "patch" for the provisioning data to raise the frequency to 25hz on the

I have been searching for a while and can't find anything specific like this. Here's is my setup: IAXy -- broadband network -- Asterisk -- TE110P -- Channel Bank -- POTS lines (FXO) Everything works fine except for the echo at the IAXy. There is no echo on the POTS end, so Asterisk is doing a good job of echo canceling. Is there any provisioning in the IAXy to do echo

Hi, hoping that experienced hands will quickly show me the right way: after a fruitless web search i am turning to this list with my rather elementary question: is there any other way to communicate with the IAXy besides using special utility software that needs to be compiled under UNIX? Here is the story: about two months ago, after some not very satisfactory attempts at using SIP (my phone

Hi. I am trying to provision my newly purchased IAXy. I tried ./iaxyprov 192.168.0.4 myiaxy.conf It print a bunch of numbers on screen and then say Provisioning is 63 bytes Total packet is 77 bytes Got response back from '192.168..0.4' And that's it. I didnt get nothing else and there isnt any solid yellow light after minutes. I wonder if anyone could explain what I'm seeing? Is

John Novack wrote: >And the only IAX2 box made is the Digium one, with it's current shortcomings ? >From reading through the archives, it seems there is currently no way to reset to factory default, no >written MAC address on an individual box, and some other instabilities requiring frequent resets. Yeah, there's the rub. Dunno if it's worth it, I'm willing to give it

Hi, I've got an IAXy, and provided it with connection data - unfortunately didn't provide a fixed ip address, but left with dhcp. Everthing went fine, and I could work a while with it. After a restart of IAXy, it didn't negotiate a new IP address, nor used the old one. I even restarted the DHCP server and cleared its cache. No success. I went to another office with a different

Hi All, I have two old S100 units (the blue ones, not the newer black ones). I am trying to reset these to factory default using the following instructions, but it is not working. Does anyone have any other suggestions to reset this model of the adapter? Tried this: 1. Remove all of the cables, except for the power cable. 2. The factory reset button is next to the RJ45 jack. Press and hold the

Ok, I searched the lists and found no definitive answer. I'm assuming the IAXy has some primitive form of echo cancel, is there anyway to adjust this? Or any ideas on what to do instead. Here's the setup, this will not be a typical setup for our company however, well whatever. Anyway it looks like this: IAXy --> Netgear router --> Charter --> Level3 --> Asterisk --> VOIP or

Yesterday I was using one of the cheap Radio Shack phone polarity on various phone outlets in my house and ended up plugging it into my IAXY. While the regular phone jacks tested OK, the IAXY tested as being reverse polarity. The tester was plugged directly into the IAXY so there is no chance of this being caused by crossed wires. Is this something that is misconfigured on the IAXY, a hardware