similar to: Problem with two hfc-s cards

Hello asterisk-users, I recently set up an asterisk server using Debian Sarge. I also added an ISDN card (AVM FritzCard PCI) to the machine. I built amd installed a new kernel (2.6.15.1) with modular support for the CAPI stuff and also integrated the FritzCard driver available from AVM. capiinfo succeeds in correctly showing the ISDN card. When talking from one PC to another via SIP, everything

Hello, I've been using * for quite a while using AVM C4 card and a few Grandstream Budgetone 102 hard phones plus couple of HandyTone 286. Echo is a big problem. I am getting used to it, but some users complain. Anyone has experience w/ regards to echo comparing the AVM C4 with two HFC-cards? Before shelling out time and money, maybe someone else already has done so, and could tell me if

I've having a big problem after having upgraded to 1.2.4 and chan_capi-cm 0.6.4 When making outgoing calls I don't seem to have any control over the CLI that is presented to the called party -- it can be any one of the MSNs allocated to the line, allocated on what seems to be a random basis. This is on a BT Business Highway line (which is essentially an ISDN2e line with two built-in

Hi all, I compiled/installed chan_capi.so without problems. When I launch Asterisk, I get the following error: --- [chan_capi.so] => (Common ISDN API for Asterisk) == Parsing '/etc/asterisk/capi.conf': Found Mar 30 19:47:52 NOTICE[16384]: chan_capi.c:2338 mkif: ast_capi_pvt(91xxxxxx,*,pstn,0x2,2) (1,2,64) (0)(0.800000/0.800000) 0 Mar 30 19:47:52 NOTICE[16384]: chan_capi.c:2338

Hi, I have done my best and tired of searching the net about the problem. If anybody could help would be a great favour. Description of Problem ------------------------ I am trying to install two Netpci cards(Traverse Technology Netjet ISDN-s) on Trixbox 2 and aim is to use in Asterisk as dailin and dialout. I compliled the driver as directed in the manufacture manual. After installation dmesg

Hello Group, Current Setup: - Eicon Quad BRI ISDN Card. - 4 ISDN BRI (Telco: Telstra) Onramp2 services. - Mode: Point2Point. - 100 Indial Number ranges. Full National Number (9 digit format): BAAAAAAXX where: B (Area code): 2/3/7/8 A (Normal Numbers) X (99 Indial extensions) eg: BAAAAAA00 BAAAAAA20 etc Requirement: - To be able send Indial numbers as Caller ID when dialing out. Configration:

All, before I start, I have read the readme and realise the dial syntax has changed since 3.5.....(and I really wish it hadn't).... anyway can somone please help me round a config issue? Previously I had a capi.caonf as follows. This config allowed me to have multiple MSN's on the same ISDN/Fritz! card under seperate contexts.

Hi all, I am trying to get Capi Dial to use a specific outgoing msn. I can't get it to work. If I make a test call to 0703241494 (same isdn line, just one of the other numbers) I don't get CLID at all. Any ideas? ; use 0703241432 as outgoing msn exten => _070.,1,Dial(CAPI/@0703241432:${EXTEN}|30|r) in capi.conf I have: [general] nationalprefix=0 internationalprefix=00 rxgain=0.8

Hello everyone, I have been using an AVM Fritz! card with chan_capi and mISDN for quite a while in PTM mode and it was working finely. Now, I needed more DID/MSN, so I switched to PTP. But now nothing works anymore :( I am using Asterisk on Debian Sarge stable and installed Asterisk along with chan_capi from apt-get. I installed mISDN from the CVS of isdn4linux.de. It is : - Asterisk

I'm getting a strange error on one of the two controllers on an AVM C2 card under chan_capi-cm-0.6.3. I have two ISDN controllers defined, both in the same group, both connections are UK ISDN2e Point to Point: On the third outbound call (both of the first two calls are handled by the second controller "ISDN2",) I get this error : chan_capi.c conf_error 0x2001 PLCI=0x301

Hi * Fans, I have some fritz cards now, followed instructions from stuart hirsts email of Jun 28: -> Thanks for your info but I think I have it working at last. Below are the steps I took which might help others. 1) Download the PCI AVM drivers from ftp://ftp.avm.de/cardware 2) Download the Chan_capi from http://www.junghanns.net/asterisk/ 3) tar -xvzf fcpci-suse8.0-03.09.10.tar.gz which

O.K. thanks a lot, Felix and Peer Oliver. But somehow asterisk keeps telling me while startup: [chan_capi.so] => (Common ISDN API for Asterisk) Jan 24 14:30:47 NOTICE[9796]: chan_capi.c:3271 load_module: Unused contr1 Jan 24 14:30:47 NOTICE[9796]: chan_capi.c:3271 load_module: Unused contr2 Jan 24 14:30:47 NOTICE[9796]: chan_capi.c:3271 load_module: Unused contr3 Jan 24 14:30:47

Hi, I tried to use the version 0.6 of chan_capi-cm for outgoing calls it works perfectly but for incoming calls it will not work: --- snip --- *CLI> capi debug CAPI Debugging Enabled -- CONNECT_IND (PLCI=0x101,DID=97,CID=0179903xxxx,CIP=0x1,CONTROLLER=0x1) == reventix: Incoming call '0179903xxxx' -> '97' -- reventix: info element CALLED PARTY NUMBER --

Hi, after having read so much about Asterisk, I went on and tried out to create a little sample-setup. I'm using a Fritz Card USB with the AVM Capi Driver and two X-Lite Softphones. Dialing between the softphones makes no problem. Calling the MSN fron an external phone also works. I'm getting to the asterisk demo-voicebox which works flawlessly. Now may next step has been to enable

Hi, I added a Fritz!PCI card to my asterisk system which is running on fc2 !. I installed the avm modules (fcpci) and when i try an capiinit and a capiinfo then everything seems to be OK (you can see capiinfo and lsmod at the end of the text) !. I installed the asterisk chan_capi module and when i start asterisk and enter the command capi info on the command line i get back: *CLI> capi info

hi all, i have a probably very stupid question/problem. for testing purpose i am trying to get asterisk running with two isdn cards. I'd only like to here the demo sound when i call the number - but nothing works. The output of show channels is not showing any channel - should there be 4 channels ? - capi info shows my two cards perfectly. The ISDN Controller's are attached to an PTMP

Hallo all, I am trying to get * with chan_capi and a ptp-ISDN with 4 lines on a AVM C4 card to work. But weather inbound nor outbound is working :( My capi.conf: ; ; CAPI config ; ; [general] nationalprefix=0 internationalprefix=00 rxgain=0.8 txgain=0.8 [interfaces] mode=immediate isdnmode=ptp msn=8993 incomingmsn=* mode=immediate controller=1,2,3,4 softdtmf=1 ;accountcode= context=demo

Hi, I like to forward an incoming call on an ISDN line to my mobile phone. Since ISDN offers two channels, I thought that this should work, but Asterisk tells me, that there is no channel available. There is no one else using this line, so guess I made a mistake in the configuration or it might not work for another reason. Here's the CLI output , the capi.conf and extensions.conf. 83086921 is

Hello, I have read the articles on echo cancellation (http://www.voip-info.org/wiki/view/Asterisk), but couldn't find a solution to my problem. We are running Asterisk 1.4.12 together with an EICON DIVA SERVER BRI-2M PCI (current driver from EICON) and some SNOM 300/360. There are few clients where we recognize echoes on both sides when we call them via ISDN. With some of these clients we

Hello everyone, I have Asterisk SVN-trunk-r7498 installed on a server (celeron 2.4 Ghz, 256MB) with a TDM40b a TDM04b and an avm fritz!card pci. I experience a problem with voicemail: my messages are good unless the incoming call comes from isdn, which means via the avm fritz!card. In this case (and in this case only) the message is disjointed and I can hear at most 1 second out of a 1 minute