similar to: FXS static and noise problem

Hi: I had an fxo card from Digitnetworks and it was working fine on my Asterisk box. I then replaced it with TDM04B. I changed the zaptel and zapata to include the four channels. When I run ztcfg, I get configuration errors: Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default) (Slaves: 02) Channel 03: FXS Kewlstart (Default) (Slaves: 03) Channel 04:

Hello all. My company currently has an older Executone PBX system that we are outgrowing. Rather than wait until the last minute to make a hasty decision, I thought it would be a good idea to do some research and compare options first. My expertise is in computers and networking, and telephony systems are mostly foreign to me. What we currently have are 5 incoming POTS lines and 25

Hi I am interested in setting up an Asterisk PBX in my office with digium hardware, and I just have a few questions in regards to what I would need. It is my understanding that an FXO card is used to interface with an incoming/outgoing phone line, and an FXS card is used for interfacing with a phone within the system. Currently we have 4 incoming/outgoing phone lines and would like to have

Hi: Astcc is working fine, except for one thing. It doesn't give the called party enough time to answer the phone. If nobody picks up in two rings, astcc reports back no answer and hangs-up. The only instant NOANSWER "value" was mentioned in astcc.agi script is: elsif ($res eq "NOANSWER") { $res = &mystreamfile("astcc-noanswer");

Hi: Please advice me of a voip provider with reasonable reseller program. I was using voipjet and it has a lot of problems. Did anyone experienced asteriskout.com service? They have good prices. Regards; Chawki Hammoud ____________________________________________________ Start your day with Yahoo! - make it your home page http://www.yahoo.com/r/hs

How are you? Fristly I would like to introduce myself in a shortly. I'm a newcomer at Newcomtech Co,. Ltd. Nowdays I'm working at TDM40B and TDM04B cards. I have installed Linux hedhat 9.0 and Asterisk software. I have configured the cards. I typed asterisk -vvvc command in the command line and then asterisk give us "asterisk is ready". Now I have to configure my asterisk

OK, here is the scenario, Asterisk @ Home 1.0 with TDM04B and TDM40B. I can receive and place calls with no issues, however, when I receive a call, the CID only shows "Analog Line" on the Grandstream 2000XP phone. Does anyone have any ideas even where to look to change this?? Is it a setting in the phone, Asterisk, or both?? Thanks, Marc

Hi, I've read through the Asterisk handbook and I'd just like clarification from someone that's implemented the above before. Lets imagine I want to use the CallingCard application and don't want to tell a client to buy a channelbank (the analog extensions are too many to connect to FXS cards), I figure I could set them up as below: Original Existing Setup

I've installed a TDM04B and a TDM40B. I haven't plugged any lines into them yet but I'm starting to see this in my logs... [root@webster asterisk]# grep alarm /var/log/messages Sep 20 09:13:22 webster kernel: Power alarm on module 1, resetting! Sep 22 11:07:07 webster kernel: Power alarm on module 1, resetting! Sep 22 16:10:55 webster kernel: Power alarm on module 1, resetting! Sep

Hi, I am building for a customer an * solution that will use 2 Digium cards. 1 x TE110P (T1 ISDN PRI) 1 x TDM40B (4 analog ports, 2 for faxes, 2 for extensions) The system will be connected to the PSTN through the T1 ISDN PRI interface. All customer extensions will be SIP phones except 2 fax machines that will use the analog FXS ports on the TDM40B card. I have been investigating on this

Hi We have static noise problem on our asterisk server. latest stable release. The card is a new TDM04B We have it installed on the following hardware Motherboard Intel SE7520BD2SCSI 2x POWER SUPPLY 730W INTEL I will not mention the other hardware because we have desactivated/changed all the other items The only 2 items that we have not changed is the mobo and the power supply. At first it

Hi, I recently got a TDM04B and after installing and getting asterisk up and running I connected a handset to one of the ports. Unfortunately I don't get a dial tone when I lift the handset. What could be the cause of this? Could someone point me in the direction of a proper config for a TDM04B? Thanks.

Hello everyone, I have Asterisk SVN-trunk-r7498 installed on a server (celeron 2.4 Ghz, 256MB) with a TDM40b a TDM04b and an avm fritz!card pci. I experience a problem with voicemail: my messages are good unless the incoming call comes from isdn, which means via the avm fritz!card. In this case (and in this case only) the message is disjointed and I can hear at most 1 second out of a 1 minute

Hi everyone, I have a question about faxing. I am running Asterisk SVN-trunk-r7498 on a ubuntu server and everything is going fine. I have a tdm40b, a tdm04b and an avm fritz!card pci plugged on it. Here is what I'd like to do: Receiving fax via the ISDN avm fritz!card, sending the fax via email (for the moment I know I can do that) but also routing the fax trough my old fax machine which

Hi All: Is there a script that I can download so I can make Asterisk send calls through a cellphone? Regards; Chawki Hammoud __________________________________ Yahoo! Mail - PC Magazine Editors' Choice 2005 http://mail.yahoo.com

Hello, I am having problems configuring a TDM400P 4 Port FXO card with groundstart signalling. The box has 2 X100P's, 1 TDM04B and 1 TDM40B. I can configure it for loopstart and it works, just not groundstart, which I need for this installation. What am I missing? Thanks! Mark /etc/zaptel.conf #two X100P FXO Cards # fxsls=1-2 # TDM400P 4 Port FXO (TDM04B) fxsgs=3-6 # TDM400P 4 Port

Hello I have an office with a T1 that provides 4 (out of 8) analog PSTN lines thru an adtran board. I want to add 4 more analog lines. Currently I have a Digium TDM40B. I'm wondering what the best upgrade path is, where I define 'best' as the solution that is most likely to work without problems (like interupt conflicts) and work with my current echo tuning . I see my purchase

I'm installing my first Asterisk server. I have a TDM04B card installed in my asterisk server (4x FXO ports). I have 5 Cisco IP phone 7960 working fine on asterisk using SIP. My configuration to receive call is working as expected meaning anyone calling on one of the 4 FXO ports is answer by asterisk and asked to enter the extension of the person to reach and then it is transfer on the

Hi Folks, Does anybody have experiences with plugging 3 TDM400P cards in one PC?? I think about a Asterisk box handling 8 incoming analogue lines and providing 4 lines to an old analogue PBX. I read a lot about trouble with the TDM400P cards so this idea seams to be not really god, or? Ciao Joerg -- _____________________ Don't PANIC

I went on a service call yesterday to find an asterisk system with a T100P card on a Qwest PRI and a TDM40B card connected to fax machines. The TDM40B LEDs were not lit, and the system did not respond to keyboard input. However, calls were being processed for the PRI and 7960 phones. I replaced the TDM40B card with a new one, and the system now seems to be ok. But I'm wondering, why