similar to: Quad PRI Problems

Hi list, Ive got a server with 6 ports on it (4+2 port card) we have a DS3 delivering all voice DS1's to us. Carrier has a trunkgroup for the first 8 span (we only have the first 6 plugged in right now). Everything works fine until we fail the primary D channel (D's are on 24,48) the secondary then picks up and outbound calls do not work, if we reboot Asterisk the D on 48 comes up and it

Hi all I have a server that has two TE412P (T1/E1+DSP) cards installed. One of them configured as an E1 PRI connected to PSTN and another one configured as a T1 E&M connected to Avaya PBX. Each card only uses two ports, so there are 2 E1 lines and 2 T1 lines connecting to this server. The purpose of this server is as a TDM trunk gateway that gets call from E1/T1 and then forward to an IP-PBX

Hello, I'm trying to set the 3rd span of a new digium quad card as a E&M T1 for Faxes to a Hylafax server. The 1st and 2nd spans are working as PRIs. When I start asterisk, the logs show a signaling error and chan_zap.c dies. I also get an error that it can't read the gains but they are the standard shown below. 2.6 kernel, Debian Stable, * 1.2 svn from feb 2007 my procedure: make

Good Day All, I am experiencing some weirdness using the E&M channel and hope you can offer a little assistance with the problem I am having. 1) call comes into channel 25 (Second Span first channel of a Digium Quad PRI from SBC-PRI) 2) Call is sent to channel 1 (First Span first channel on the Digium Quad PRI connecting an ADTRAN via E&M Feature Group D) 3) Between rings one and two

Hi all, I've got a fairly simple setup, a 4 port zaptel T1 card with 1 PRI and 2 flat e&m T1's coming into it, and its working perfectly except for one small thing. When people dial any of the numbers on either the PRI or the T1 from outside of the pbx, they dont get the "ringing" sound. It just directly connects the call. I know this isnt much, but its started to

I just had the same exact problem this morning. The only thing I've done in the last couple of days is update update zaptel. I rolled back my zaptel to 2/11/04 from 3/8/04. And kept my libpri from 3/8/04. I never had this error before updated. I had other issues, but not this one. -sb -----Original Message----- From: asterisk-users-admin@lists.digium.com

TE410P card down. I have three (3) TE410P in one machine running asterisk with SS7. My problems started last week when one of my cards started switching to E1 every time after reboot. I set the following in dahdi.conf and that solve the problem. /etc/modprobe.d/ options wct4xxp t1e1override=0x00 Now all 4 ports on that card is down with Red Alarm. I tried rebooting the machine and

Evening, My latest asterisk box is having a difficult problem. It is configured with one TE210P and TDM400P with four FXO modules. I'm running FC6. The TE210P only has a single PRI. When the system boots, it is completely random what order the zaptel modules will get loaded in. Sometimes zttool shows the FXO as the last span, sometimes as the first. When it does load as the first, which

List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to

We have install a DS3 with 28 DS1's we have an Adtran MUX breaking out the DS1's, we are trying to setup the system with 2 dchannels for each 4 DS1's. Everything looks fine when modprobe zaptel and wct4xxp and ztcfg -vvvvvv but when I asterisk asterisk it says: Aug 10 16:33:32 ERROR[8954]: chan_zap.c:6750 mkintf: Channel 24 is reserved for D-channel. Aug 10 16:33:32 ERROR[8954]:

I am having a problem with a new PRI turn-up on dahdi 2.5.0 and asterisk 1.8.5 that I have not seen before. The PRI is setup as B8ZS, ESF and the span shows up and ok. This PRI is merely a crossover T1 going into an old DC0 class 5 switch. I am getting the following errors over and over again [Aug 16 10:26:10] NOTICE[8002]: chan_dahdi.c:3043 my_handle_dchan_exception: PRI got event: HDLC Bad FCS

I have just finished installing a new asterisk box at my work. The box is quite hefty, dual Zeon 2.8s with SCSI drives and 2Gb of memory. I have a 4 port Digium T1 card for channel bank and PRI access. I activated a PRI from a local CLEC (DMS-500 based, National protocol). This PRI is on slot 2 of the card and is set as the primary timing source. It is ESF/B8ZS. All the software is latest

My PRI is being reset at least once a day with the following errors in the logs. zaptel, zapata, libpri, and asterisk are from CVS this morning.. This has been happening for weeks on all versions (including -stable). the T100P card appears to NOT be sharing an IRQ. xenon# cat /proc/interupts CPU0 0: 1203977 XT-PIC timer 1: 3 XT-PIC keyboard 2:

I am trying to receive both CID and DNIS from the telco through a non-pri T1. Currently I have the T1 setup and operational both outbound and inbound calls are completed as should be expected. The calls came in and were placed in the context specified in zapata.conf on exten => s,1. I have requested that the telco provide callerid (they call it ANI) along with 10 digit dnis for my 800

All, Having problems terminating to a Nuvox PRI, the tech at Nuvox is saying Asterisk is transmitting in CCITT (aka ITU?) when they're expecting (and will only accept) ANSI. The question is, is there a simple way to change this or am I stuck with rewriting code? I googled and checked the mailing list and found nothing, I could be barking up the wrong tree I guess. PRI is not my forte.

Im having a problem getting the 2 cards working together. I added the TDM with 3 FXO and 1 FXS board. The TE405p is working fine. THe TDM registers and identifies the FXO's and FXS but cant get them to go off hook. I hope someone can help. Asterisk seems to THINK its dialing it sends manager status as dialing, and it just sits there with no tones, on the phone dialing out. If I dial,

Asterisk 16 latest DAHDI 3.0.0 latest Excerpt from chan_dahdi.conf is shown below. I'm trying to enable fax detection on inbound calls so that I can take appropriate action in the dial plan. "dahdi show channel 1" shows "Fax Handled: no". Does that mean that I don't have it configured correctly? [channels] ; Span 1: WCTE2/0/1 "WCTE23X (PCI) Card 0 Span

I know this topic has been covered before - I just want to make sure I am understanding this correctly. | ------------------- | | | | T1 | Channel Bank | | ----------| | | | T1 Cross | | | | | | | | ------------------- -------------- | Asterisk | | | |

Hello. New to the list. We're in the process of deploying Asterisk. Actually, we're going live tomorrow, and I just found out that my Zaptel cards have been mis-configured. I'll preface this by saying that I have looked in the wiki, read through the samples, and attempted to call Digium (they're closed.) So I'm praying that someone on the list can help me out! I have two

Out of the blue i started receiving the following error on my PRI line which connects my asterisk server to a Norstar 0x32 key system. The asterisk zaptel.conf file was configure as follows and this config worked for 6 months until friday. Nothing was changed on either system prior to friday. here is teh zaptel.conf span=1,0,0,esf,b8zs bchan=1-23 dchan=24 span=2,0,0,esf,b8zs bchan=25-47 dchan=48