similar to: Maximum number of Digium Trunk Cards

Hi all, Which is the practical (from your experience) limit of the number of X100P cards installed in a single Asterisk box? Asterisk can work reliable with 6 X100P cards in the same box? Anyone know when the 4 ports FXO Digium card will be available on the market? Many thanks, Dan P.S. Please do not aswer with RTFG ...tried before without success...:-))

Is there any technical difference between a T1 cable and a cat5e patch cable as far as using them with Digium T1/E1 cards? Can PRI circuits terminating at a smart jack connect successfully to Digium cards using straight through CAT5e cables? If so, are they using all of the pins in the cable? Thanks in advance

This might be a newbie question but I'm just wondering how would it be possible to have 30 analog lines using asterisk for PBX by just using TDM40B and X100P (or are there any device>), if an ordinary PC support just 4 PCI slots? the maximum scale i guess would just be 2 x 8. Adding a new PC just for this purpose would be costly. I would appreciate your comments. Thanks.

> The documentation mentions that the Digium channels can be split into some > voice channels and the remainder of the channels used for routing IP > traffic. > > Does any one have this in use in conjunction with Asterisk? Does it work > well? Would you recommend it for a production server? > > Obviously, if this works, this makes for a cost effective platform where

Hi there, I'm quite new to asterisk and digium hardware. I needed to know which of the digium cards supports E&M signaling?. thnaks, Gonzalo --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.713 / Virus Database: 469 - Release Date: 30-Jun-04 -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello, I am looking to buy a large number of TE410P cards for a big international project. I have studied the documentation and zaptel.conf and as result I have the following questions: 1. How do you switch the card from ISDN PRI TE to NT? This means from being configured as User Equipment (the PABX) to be Network Equipment (the Exchange). 2. How do you configure the card for E1 or T1? 3. In

Hi it's possible to use a Digium TE110P Single T1 / E1 PCI Interface for supply a E1 link to a old PABX ? Thanks

I currently have Asterisk deployed in my office with a TE411P. On the first port of this card is a T1 from the telco setup for D4 AMI. Unfortunately, I'm not receiving caller ID on inbound calls from this line. The caller ID information is arriving in the form *ANI*DNIS*. In zapata.conf, I have signalling set to em_w. The DNIS always arrives correctly, but I'm never receiving the ANI

Hi all I have a server that has two TE412P (T1/E1+DSP) cards installed. One of them configured as an E1 PRI connected to PSTN and another one configured as a T1 E&M connected to Avaya PBX. Each card only uses two ports, so there are 2 E1 lines and 2 T1 lines connecting to this server. The purpose of this server is as a TDM trunk gateway that gets call from E1/T1 and then forward to an IP-PBX

Hi, I've found that neither Michael Manousos patch nor ztdummy driver do not fix musiconhold sound interruption problem up to acceptable quality level. Sound is choppy here anyway. It is my understanding (please correct me if I'm wrong) that if I have a Digium card in my asterisk machine, these problems should be gone 'cause those cards provide some reliable timing. So I have no

Just noticed this today: Digium TE220B Dual Span T1/E1 PCI Express Card with Octasic DSP-based Echo Cancellation Module<http://www.voipsupply.com/product_info.php?products_id=3352> It's about time Digium got on the ball and made PCI-e cards. What are people's experiences with this card? Anyone know if there are plans for a PCI-e analog card for FXO use? -------------- next part

I am experimenting with an asterisk setup in my office. The last bit I have to test is working with analog lines. I have TE411p digium card, with an ISDN line plugged into the first, a channel bank plugged into the second port, and the last two ports empty. I have the following setup in my zaptel.conf: span=1,1,0,esf,b8zs bchan=1-23 dchan=24 span=2,0,0,d4,ami fxsks=25 And in zapata.conf, I

Hi, I bought a Digium Quad E1 card model TE406P. Till now, I can't make it work... I mean, I have red alarm when I configure one E1. The provider is in France (France T?l?com) and I use the following zaptel config : span=1,1,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 I'm using Linux 2.6.15 and when I run ztcfg -vvvv, it seems that all channels are configured... So can someone

I'm wondering if anyone has had any good/bad/indifferent experiences with Supermicro P4SGE P4 FCPGA motherboards and Digium cards? I'm looking to use this MB in an E100P E1 card solution, and I haven't had the ability to test with that configuration before I ship a system overseas (since I don't have an E1 to plug into it, it's hard for me to test, and I don't have

Hi, For the project I've used the Eicon DIVA card. It has 8 BRI ports, and for about 25% of the time there are 7 or 8 in use. So we want to replace it with an E1 card. Only issue is, replace it with what? The idea we have been playing with was to get a Digium E1 card (we already have bought lot of Quad E1 cards :-) and then just put it back to back against Asterisk server. And instead of

Hi, I have successfully configured DIGIUM card and successfully communicated through it to the another E1 card running application. Can anybody tell me does TE120P support MFC/R2 protocol. Thanks and Regards sanchal singh

Hello, I've seen various suggestions thrown around for hardware when people ask, but can we all agree on some basic hardware recommendations for a few basic setups(and post them on a website) to make it easier for new people to avoid some of the hardware/software pitfalls when they are setting up their first systems. Something like this: (THIS IS JUST A PROPOSED LAYOUT SO PLEASE BE GENTLE)

Hi, For training sessions, I'm evaluating the possibility to use a single physical server to host 5 virtual servers, each with its own Dahdi PCIe card, instead of using 5 physical machines, hoping a single physical server would easier to transport, more quiet and cheaper to provision and maintain. As you can guess, each machine shouldn't be heavy loaded (a couple of calls, for each). If

Hi, I am looking to buy 2 used 1 or 4 ports E1 Cards. If you have one, would you please contact me? Thanks, Pete -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20081217/48afd68d/attachment.htm

I know, I know, check the archives but I can't find an answer since the new cards are well, NEW! I understand the whole issue of expandability and flexibility of using a T1 card and an Adtran 750. FXO or FXS, you mix and match. With the new card offerings from Digium I can easily put a 4CO by 8 Station system together. Barring the extra interrupts, extra CPU Cycles of extra interfaces, is