similar to: How to fix a Blue Alarm?? Line Noise?

Does anyone have any experience getting a Mitel SX-200 EL/ML PBX system to work with *? I'm not getting inbound or outbound calls to work. (Inbound caller gets line busy tone.) SETTINGS FROM MITEL: I built a Crossover cable and connected it like this: PSTN--T1--ASTRISK--T1--OLD MITEL -Crossover Cable Pin-out: 1 - 4 2 - 5

Hi, Ok, I put the new TE410 into our system last night - This is the second TE410P card. There is also TDM400P in Slot 5 with IRQ 9 which is shared with aic7xxx (SCSI) According to "cat /proc/interrupts", the new card is in the second slot using IRQ 11 (the first card is in slot 1 on IRQ 10 - but always has been). With only the original card install, there has been no issues with

We have integrated an Asterisk (TE110P) and a Mitel SX200. We usually get over 500 frame errors and over a 500 slip errors per hour. When the errors reach 1000 per hour the Mitel will take it's T1 card offline. At that point no calls can be routed from the Asterisk server to the Mitel and the TE110P reports a Yellow alarm. What can be causing all these Frame and Slip errors? We have been

I have a couple of live T1s sitting around and they are not ISDN(like most of the people that are using Asterisk seem to be using), they are regular old 24 channel, robbed-bit, E&M wink start, D4AMI T1 circuits. Can I get these T1s to work with a T100P Digium card and asterisk? Searching through the lists and the documentation I haven't seen any examples of how to configure this kind

I need to create a couple of tie lines between a legacy system and an Asterisk system. I was told that the tie lines are E4 Superframe E&M. I have done E&M wink but have no idea about E4 Superframe E&M and Google is not helping me here. Does anyone know about this type of signaling and if Asterisk can handle it? Thanks, Steve

Attempting to talk to an Eagle Telephonics switch at a disaster exercise. Didn't think a plain old E&M wink start T1 would be this much of an issue. We finally got the Eagle to accept a call from *, but whilst I can hear the person on the Eagle, they can't hear me. When they initiate a dial out I only get the first 2 digits from their switch... Does anyone have decent

I have a bit of a weird problem that I'm having great trouble debugging. I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID, which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS. Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls. My

Hello all. I just received a TE110P and am trying to hook it to my Mitel 200SX has anyone successfully done this? My configuration is as follows. Asterisk -> TE110P ->Kentrox (csu/dsu) -> Mitel T1 Card. All I get is a blinking yellow on my TE110P card and an alarm on my Mitel. T1 card. Any advice would be great. Zaptel.conf span=1,0,1,d4,ami e&m=1-23 dchan=24

Hello All, I've mostly solved my DID problem from a few days ago. Apparenly the lines weren't configured properly. Now heres the next question. 12 E&M wink lines from telco. I have them all plugging into an Adtran 750 with FXS cards. The Adtran ports are configured DPO. How do I signal this from Zaptel. I have them setup E&M in zaptel.conf and EM_W in zapata.conf. They

I have a problem which I need to resolve. We are trying to put an asterisk between a Mitel PBX and the world. We are adding Voip service via Asterisk. Here is are config files for the settings but our problem is the following. We are able to send calls to the Mitel pbx and it's the T1 connections is green saying it's ok. The support department from Mitel said that they use e&M and

Hi list, Sometimes I receive a Red Alarm in my E1 trunk (E&M immediate start signaling), and just few seconds after this, all alarms are cleared. This problem ocurrs many times/day, and if are calls in progress, these calls just hang-up. Could it be an asterisk bug? Or may I contact the PSTN provider? Thanks Eduardo

Hello, I am missing any description of zaptel/DAHDI alarms. The TE200 series user manual contains only a description of LEDs states. These alarms states are visible in zttool/dahditool or in astersick CLI (zap show status) and I wonder what is the real meaning of these alarms for E1 channel. Possible alarm states (based on zaptel.h 1.2): 1. No alarms 2. Recovering from alarm 3. In loopback

Howdy, New installation, trying to connect an RBS T1 with AMI/D4 framing and E&M Wink. Using a Sangoma A102d and asterisk 1.4.22-2 on Centos5 (Trixbox 2.6.2.1). Outbound calls work fine, but inbound calls fail to read the DID information, and with debug set to 10 I get the following: [Feb 2 19:40:23] DEBUG[25184] chan_zap.c: Monitor doohicky got event Wink/Flash on channel 3 [Feb 2

How would you categorize a Yellow Alarm sensed by the Asterisk side in a Legacy PBX integration? We have a Mitel SX200 connected to an Asterisk(1.2.4) with a TE110P. Twice today (first time in over a month) we received a Yellow Alarm on the TE110P. I have been able to clear it easily by restarting zaptel. Thanks in advance! -------------- next part -------------- An HTML attachment was

Asterisk is getting red alarms on my T1, sometimes once or twice a day, but today it happened 5 times. Even once is too many. Every call in progress is dropped. Please help! What do I need to do? What can I try? I've googled and searched this list and can't find anything. Here's an example from the logs: Feb 7 13:37:54 WARNING[32451] chan_zap.c: Detected alarm on channel 6: Red

Hi, all I have installed TDM400 with 1 FXS and 1 FXP ports. Now I am goig through documentation on how to configure it. It mentions 3 protocols: Loopstart, Groundstart and Koolstart. Which one do I use? Can someone send me sample zaptel.conf file for Australia? This will save me some time and will be used as a working example. Thanks, Rudolf

Can anyone help me with the term that SBC uses to refer to disconnect supervision? I have an Adit 600 channel bank which has helped improve the disconnect detection time down to about 8 seconds. This is still causing some issues in particular with call progress enabled in * we are having a few disconnects while calls are in session (about 2 reported in first 5 days of use). I have talked both to

Eric "ManxPower" Wieling wrote: >> >>> span=1,1,0,d4,ami >>> e&m=1-24 >>> > > Looks like you have told Asterisk to get it's timing from the Mitel. > I'll bet the Mitel is trying to get it's timing from Asterisk. > > Try span=1,0,0,d4,ami and run ztcfg -vvv > I just set this back. It was originally set to your

All, One of our customers is using a Telrad PBX, we are providing phone server through asterisk via a T1 using e&m directly connected to the Telrad system. We're using a T1 cross cable as normal, the T1 part works great. No alarms. When we try and dial out the Telrad using a direct trunk group, the call fails. When looking in the asterisk console I noticed only 1 or 2 digits are seen,

Hi List, I'm finding a solution to provide failover and load balancing features to my IVR system. Anyone suggest me what is the best solution please?. what the hardware I should use ?. I heard about RedFone, but someone on the mail list said that it is not good because TDMoE module in asterisk is not so stable and TDMoE is stale. And It seems that RedFone doesn't not support load