similar to: IAX2, can't receive calls

I'm afraid I'm quite confused by what I've found on the Wiki. I have the following dial plan that works: exten => 2201,1,Dial(sip/2201@gs1.uucp,20,) exten => 2201,2,Voicemail(u2201) exten => 2201,3,Hangup exten => 2201,102,voicemail(b2201) exten => 2201,104,hangup When the phone is in use it goes to voice mail as busy. When not picked up, as

My BT100 won't register with my Asterisk server, it always comes back with a 403. I've included my sip_additional (only one to to have the username 2201) and a portion of the sniffer trace (packets 27 & 28). This has me puzzled as I have my SPA-3K working (incoming and outgoing). On my BT100 I get no dial tone, I can't call it (asterisk says the extension is busy) but I can call

OK, this may seem to be an obvious question but where do I find the reference docs? I'm getting this error message: Timeout, but no rule 't' in context 'home' about this line: exten => 2201,1,Dial(${PHONES1},20,Ttm) I know the problem is with the 't' but I don't know what the parameters mean. I looking for a man page basically. -- Linux Home Automation

I'm seeing all sorts of problems and it's probably more of my lack of experience than anything else. I have a BT100 running 1.0.6.7 code. When I go to the status page it says it's not registered (hmm, that's not good). I also can't get dial tone but I can dial! I'm afraid I'm lost any good pointers? I've done a sip debug and all I'm seeing for the BT100 -

Just a note to those of us with the SPA-3000 that have had a hard time with the 'volume' of calls from the PSTN (we're on the line they're on the PSTN). Anyway I change the parameter: PSTN To SPA Gain to 6 and the volume is fine (it's under the PSTN Line tab). I don't remember seeing this on the list so I thought I'd add it here. Guess I should add it to the wiki (a

I recently lost my setup (bad drive) and I'm now trying to get my setup back. I have Asterisk setup to a BT100, a Cisco 7960 (7.2 SIP) and an SPA-3000. I can call the phone extension, I can call from the phone on the SPA to other extensions and I can call out to the PSTN. What I can't do is to call from the PSTN to through the SPA to Asterisk. It rings twice then I get fast busy. I

I had my setup working properly under 1.2 and after a disk crash I decided that I wanted to try Asterisk 1.4. So far I can transfer between phones and I can dial out. What I can't get working is to get an SPA-3102 to 'send the calls' to Asterisk. I have the device added to the sip.conf file and it shows up in users and peers (but not in registry). Where do I start with debugging? --

Does the ${BLACKLIST()} function allow for values other than 1 to be returned and if so how can I use that is the AEL? Can I use the function in a switch statement? -- Linux Home Automation Neil Cherry ncherry@linuxha.com http://www.linuxha.com/ Main site http://linuxha.blogspot.com/ My HA Blog Author of: Linux Smart Homes For Dummies

Hello, I am trying to setup my Asterisk box to accept calls from the FWD network. I've followed all the config advice / samples I've found on the web. Making calls to devices on the FWD network from my Asterisk box works flawlessly, but whenever I try to call my Asterisk box from a FWD client I get a busy signal, and a "Call Disconnected" 486 error. What's odd is that I

Hi Folks, Just wondering if anyone can give me some pointers, I'm configuring Asterisk to talk to FWD's new IAX service. The asterisk server is behind an iptables NAT Firewall, with port 5036 forwarded: $IPTABLES -t nat -A PREROUTING -p udp -d $EXTERNAL_IP --dport 5036 -j DNAT --to-destination 172.16.20.200:5036 I can make outgoing calls just fine, but when I receive an inbound call

Hi All I'm trying to get two Asterisk servers to talk to each other using IAX(2). I've read the WiKi and the docs and tried the examples..... I can't get it to work (I have 2 x 7960's registering on one server and 1 x 7960 registering on the other). I've set them up as follows... The two servers are set up as friends and have consecutive IP address's. The setup is

I'll admit it. I'm a asterisk newbie (but no stranger to telephony). The setup is simple: two Grandstream BudgeTel 100 phones (SIPPhone specials) on a private segment calling to a Linux box acting as the segment's firewall with a leg on our public network. The phones are setup as SIP/phone1 (x1000) and SIP/phone2 (x1001), respectively (thanks to the Asterisk HOWTO). Getting IAX

Hi, I had a FWD account set up with asterisk (using SIP) and it was working fine both ways. I switched to IAX2 and now I can't get incoming calls from FWD. People who call my FWD number get a "480 - user is not online" message without any traffic reaching my box. I can call FWD numbers fine over IAX2. It seems fwd isn't trying to place the call over IAX2 because it thinks

I'm attempting to get two Asterisk 0.4.0 PBXes to communicate with one another using IAX/IAX2 trunks. I've managed to get a semi-functional NAT Firewall working as a PBX (with Asterisk running directly on the firewall itself), but there are issues with bind()ing to various interfaces which is causing outbound SIP issues. To get around these issues, the idea is to do something like

G'day list, I am getting a lot[1] of traffic on my Internet link, ICMP messages from 69.73.19.178 telling me UDP port 5036 is unreachable (this IP address belongs to iaxtel.org). I see from the wiki that IAXtel supports only IAX2 from December 2003. Fine, however it looks like my * still wants to try and register using IAX1, and I can't find how to turn this off. This situation is

Hi :) I've had all this working before, but I'm revisiting it, and in short, I currently have huge problems receiving incoming calls. I've been trying with both FWD and voiptalk.org. I'm running CVS HEAD of asterisk, zaptel and libpri as of yesterday afternoon. Would someone mind helping? :) My machine is 10.0.0.1 on my LAN, but the ADSL router has 10.0.0.1 set as the 'DMZ

When starting *, I get the following when the chan_iax2.so loads: [chan_iax2.so] => (Inter Asterisk eXchange (Ver 2)) == Manager registered action IAXpeers == Parsing '/etc/asterisk/iax.conf': Found WARNING[16384]: File chan_iax2.c, Line 4980 (set_config): Ignoring port for now == Registered channel type 'IAX2' (Inter Asterisk eXchange Driver (Ver 2)) == Using TOS

Using DIAX softphone which seems to be working OK can get to VM/echotest etc in the demo context Am trying to setup FWD but get the following problems Can hear it ringing when dialing FWD no 612 for time. Connects but no sound from remote end. Does anyone have any suggestions. Softphone on 192.168.0.2 asterisk on 192.168.0.3 Netgear RP114 doing NAT to the internet port 5060 being forwarded to

Hi, I have some questions regarding IAX, IAX2 and encrypted authentication. How can I know if IAX or IAX2 is used between two * servers? There is any guide about how to configure encrypted authentication (not in clear text)between two * servers? I "hear" on this list a couple of days ago that port 5036 is the default one for IAX and something else (4XXX) for IAX2. Trying 'iax

Hi, I'm slowly getting to grips with *. My next quest is to get IAX2/FWD calls working. I've setup a fwd account and added IAX capability to it via the website. I got the email saying it had been done with some welcome text and sample phone numbers to try, such as 10001 for the answer phone. I followed the setup example on the fwd site for configuring * to work with fwd's IAX.