similar to: Problem with IAX trunking

I'm trying to make a call from an IAXPhone client - through the * PBX to an 888 number using the IAXTel link. I'm using the basic conf files for extensions and iax. I get successfully connected (at the "Attempting native bridge" line of the output) and am then able to talk both ways for 20 to 30 seconds and then the IAX phone appears off line. If I wait on the PSTN line for

G'Day, I have a bit of FireFly problem that hopefully someone has seen before. What happens is if I make to or receive a call from the FireFly network the call will connect successfully. However, around 10 seconds after I answer the call I am disconnected. The weird thing is same thing happens if I make a call. I've had a look at the * console and I can't see that my * PBX drops

Through my Asterisk server, I am trying to use IAXTel to dial 800-type numbers (yes, I know I can do the same thing with FWD and others via SIP, but I wanted to play with IAX a little). It appears I'm running into some sort of a codec mismatch or something because it's not working right. The SIP client is a SPA-3000. In iax.conf, I have something like the following: [General]

I am trying to work out IAX <--> IAX communications with my * box. I have a registration with iaxtel and I thought I would start there for my learning. I am able to call the number for Digium's support line (700-428-6000), but the sound is horribly chopping. Some reading revealed the jitterbuffer settings, so I enabled them in iax.conf. I have the following now: ; Inter-Asterisk

[ Sorry, I incorrectly copied some Reference headers into this post and tacked it onto the wrong thread. -Steve ] So far, I have been able to receive incoming iaxtel calls via my assigned 1-700-xxx-xxxx number, but only when using md5 authentication in iax.conf: [iaxtel] type=user ; Incoming calls only context=incoming auth=md5 secret=<mysecret> ; Required for

When I try to call iaxtel it goes to codec ADPCM even though I have define in iax.conf gsm Call accepted by 69.73.19.178 (format ADPCM) -- Format for call is ADPCM My settings: [general] port=4569 register => xxxx:xxxx@iaxtel.com bandwidth=high jitterbuffer=no tos=lowdelay [voipjet] type=peer host= xxx.xxx.xxx.xx secret= xxx auth=md5 notransfer=yes context=incoming disallow=all ;

Hi All, Sorry if this has been covered in the past; I've tried searching the archives, but haven't had any luck finding a similar problem. Basically I have problems when using IAX2 (which I now understand is just IAX). I have three IAX connections setup - VoicePulse, IAXtel, and an Asterisk IAX<->PSTN termination provider here in Sydney (ATP) If I try to use the CVS STABLE version

Hi, I have a problem with IAX accounts... I set up a few months ago an Asterisk server, with mysql support to load iax accounts. Settings seems fine because apparently the system works as expected. Yesterday I tried to add another iax account in the iax.conf directly. And I have a problem with this new account (named 444). I can authenticate from 444 to the server, and I can receive calls from

I had a working 1.0.9 asterisk installation and tried to get a Firefly IAX phone to register, but it was failing. I upgraded to asterisk 1.2.5 and the PBX is working fine, but the IAX phone still won't connect. Below is my iax.conf and the output from setting iax2 debug while the phone tries to connect. Could somebody please give me some pointers? This doesn't seem to be a normal

I created an account at IAXTEL.com to route 1-700-XXX-XXXX calls through. IAXTEL.com gave me a number (example) of 700-555-6226. I have made the following changes to my: /etc/asterisk/extensions.conf: [iaxtel700] exten => _81700XXXXXXX,1,Dial(IAX2/myusername:mypassword@iaxtel.com/${EXTEN:1}) exten => _81800NXXXXXX,1,Dial(IAX2/myusername:mypassword@iaxtel.com/${EXTEN:1})

I signed up for an IAXTEL account and have been trying, unsuccessfully, to get it working. In IAX.CONF I have: [iaxtel_out] type=peer host=iaxtel.com username=USERNAME secret=SECRET auth=rsa inkeys=iaxtel [iaxtel] type=friend context=incoming host=iaxtel.com auth=rsa inkeys=iaxtel However, when I start Asterisk, I get the following warning: [chan_iax2.so] => (Inter Asterisk eXchange

After battling for days trying to figure out what was wrong with my iax.conf it was determined that I do not have any inkeys set on the digium server. Now whether that is something new or just in a few cases I am not sure. Messing around and reading on IRC and the mailing list I could get certain things to work and then break other things. Now I can dial a IAXTEL number, 800 number and FWD

I need to debug a call quality issue with remote users on the other end of a satellite link. The symptoms are: we here on the Internet side can hear them just fine. On their end, things work sorta OK most times, but they often suffer from severe dropouts and digital warbling, both of which I attribute to them missing packets. Often times they can't make out a word we are saying while we can

I tried to connect my * to IAXtel, but i always get this errors. chan_iax2.c:5849 socket_read: Registration of 'mnetwork' rejected: Registration Refused On dial a iax number i get: chan_iax2.c:5526 socket_read: Call rejected by 69.73.19.178: No authority found chan_iax2.c:5528 socket_read: Immediately destroying 3, having received reject chan_iax2.c:2411 iax2_hangup: We're hanging

All, I have an issue with IAX that I can't comprehend. Approximately every eight minutes my servers go unreachable. They stay unreachable for exactly 10ms. I have two servers running IAX and it happens on both servers simultaneously. I have searched the archives and see similar issues, but not the exact same one. I am on the current CVS stable version of *. Also, during IAX calls,

Hi! I just wondered if anyone would mine posting their successful jitter buffer settings here for me if they get a moment ?? I've spent a few hours trying to set the jitter buffer up reasonably logically and can definitely tell it makes a difference and can introduce latency and echo if setup incorrectly but I can't see a good post anywhere describing properly what the three settings

I'm attempting to get two Asterisk 0.4.0 PBXes to communicate with one another using IAX/IAX2 trunks. I've managed to get a semi-functional NAT Firewall working as a PBX (with Asterisk running directly on the firewall itself), but there are issues with bind()ing to various interfaces which is causing outbound SIP issues. To get around these issues, the idea is to do something like

Hi, Acording with http://www.voip-info.org/wiki-Asterisk+iax+rsa+auth, both sides should have "auth=rsa" in their respective section at iax.conf. But i've found that if server includes this option, the client keeps saying "No way to send secret to peer". My links with FWD and Iaxtel are working fine, this is a test i m doing with 2 asterisks i configured. Also, if i use

All, I have spent the last couple of days looking through the mail archives and the documentation on the Wiki, but have not been able to find a solution to the problem. The version of code I am running is from CVS as of 6/30/04. What happens is that when I make an IAX call to another IAX client the caller receives a really bad echo. All of the documentation I found around using

<BLOCKQUOTE style="PADDING-LEFT: 8px; MARGIN-LEFT: 8px; BORDER-LEFT: blue 2px solid"> <DIV>Hello,</DIV> <DIV>&nbsp;can someone tell me what's wrong with this? I can't make toll free calls via iaxtel. Here's the definition in my extensions.conf</DIV> <DIV>&nbsp;</DIV><FONT size=2> <DIV>[iaxtel-trunks]</DIV>