similar to: Can the originator of a call transfer it?

Hi, I would like to make a call and then when I am connected to the destination to transfer the call to my coleague in the office. When we receive the call it is easy using "#". But when I am the originator the "#" doesn't work. Can you give me some suggestions? Best Regards, Miroslav Nachev COSMOS Software Enterprises, Ltd. Tel: (+359-2)

I am using Polycom 501s with asterisk 1.2.4. When transfering to call parking wih "#1" -> 700 the user is able to hear asterisk tell him what extension the call was parked on. However, when I press "transfer" -> blind -> 700 . The user is not able to hear what extension the call was parked on. It seems like the polycom is hanging up before asterisk is able to

Hi I am using Asterisk 1.2 and for the life of me, I am unable to transfer outbound calls (eg calls I initiate from sip extensions). When I press #, nothing happens. Inbound calls transfer fine, but only once per call. The problem happens: - With both software and hardware phones. - With calls going out through the ZAP channel and to internal SIP extensions. - After I have transferred an

I can't seem to retrieve a parked call. Here is what I do: Call from phoneA to phoneB Answer phoneB Press Flash/Callwait on phoneB Press 700 to park the call A voice says that the call is parked at 701 When I try to dial 701, I don't get connected to the parked call Below is the asterisk output when I tried to park

Trouble in Parking Paradise! Good Day all, I have a situation that I have tracked as far as I can take it and am looking for assistance into the matter. My setup.. Asterisk 1.0.1 with the AMP config environment. When I have auto attendant answer the phone and I dial my extension "2204" The call come through and If I park it it gets place into extension 701 (the first parking

Ok I have read every line in the wiki for call parking. HELP PLEASE I need to perform a simple call parking that upon timeout will ALWAYS rings back to the extension that actually parked the call. Am I just crazy or is this not possible. >It has been narrowed down to the CONTEXT the call was originally located in. >I need to figure a way within the parking application to set the

It has been narrowed down to the CONTEXT the call was originally located in. I need to figure a way within the parking application to set the extension I want the call to ring back to. Specifically I want to set it to always ring back to the phone that parked it. Example, below .. When the call rings only a specific phone http://pastebin.ca/2452 the context it originates from aa_1,2204,1

PLEASE CONFIGURE YOUR AUTORESPONSERS TO NOT SEND MESSAGES TO PEOPLE WHO POST IN MAILING LISTS YOU SUBSCRIBE TO. This is an extremely rude thing to allow, and is becoming increasingly common, especially with users of the Asterisk-Users list. Daryl _____ From: s.speckenheuer@posservice.de [mailto:s.speckenheuer@posservice.de] Sent: Friday, February 04, 2005 6:41 PM To: Daryl G.

I am using IAX to send a call to my cell phone. I want to be able to hit # and transfer it back into the office. I have added tTr to the dial command and hitting # prompts me for the transfer, but after I start dialing 103, it stops at 1 and tries to transfer it within nufone instead of my dialplan. This is the debug output: -- Called me@NuFone/1515480XXXX -- Call accepted by

Hello All. I am having some trouble with call transfers when asterisk is the 2nd party called and I hope to benefit from your experience. I want to use asterisk for call park/pickup and have configured openser to relay calls made to ruri 700-720 to asterisk running on localhost:5069 Call flow: phone A calls phone B (both phones are polycom) Phone B answers then phone b

Hi all, Does any can give me some example to setup call parking and call transfer of a call? In my understanding, call parking and call transfer should be like something below. Am I right? ango Call parking: caller A -> callee B callee B park her call callee B get back her call in another phone Call transfer: caller A -> callee B callee B transfer to C finally: A talks to C

Hi, Is there a way to do a blind transfer within an asterisk dialplan (like '##')? The reason I need this (I think) rather than a regular Goto() is that I'm trying to do one-touch parking. I can park a call using one-touch parking and then pick it up again, however if I try to re-park the call, it gets lost. I think that is because asterisk thinks I'm still on the park extension.

I have an issue with call parking and hope there is some undocumented feature for this. ;-) We are replacing our legacy PBX with asterisk, but to save money over time (handsets and network), I am trying to maintain the use of our legacy PBX. Asterisk extensions can not use the call parking features (not usable over trunk cards) of the old PBX, so I have to get the old PBX to use asterisk's.

Hi, I'm having problems with transfer from an analog line via a X100p and Cisco 7960's running SIP. With an attended transfer the a call comes in, I transfer it to another 7960, they answer I announce the call, press transfer again, the two parties talk for 1-2 seconds then the analog line drops, though the Cisco phone is not aware of this, i.e. nothing on the screen changes. The

Hi All I'm using the PickUp application from Bristuff to allow me to pick up channel groups across Zap and Sip. The only snag is that having picked up a call with it, you can't then transfer it on. Taking a dive into app_dial, it looks like when you specify the T option, it does: ast_set_flag(&(config.features_caller), AST_FEATURE_REDIRECT); Since there's nothing like that

I am having a hell of a time with transfers. First the Snom issues: The transfer button on the Snom 220 does not work. I have read about setting break key off in the advanced page of the web config but the Snom 220 has no such option. At the moment I am having to use the # transfer hack which makes this phone look really stupid to have buttons on it that cannot be used. Anyone know how to

Hi all, I enabled recording (mixmonitor) in queue and process started after queue member pick the call. But recording will stop after picking up by another extensions of call transfer/parking in the same call. Is it possible to continue to record the call for call parking/transfer, how? Rgds, ango

We are going to replace a BizFone with Asterisk and one of the features that I haven't been able to emulate is the PBX hold. We can put a call into hold with the * key and every 30 sec the phone gets a beep to remind us it is there and the caller on hold can hit # for other options. The closest I've come with Asterisk is call parking, and that doesn't quite do it. Using the

Hi, I've been working on migrating my asterisk from zap to sip (due to compatibility issues between my TDM400P and my Hauppauge PVR500). I've purchased a Linksys SPA-3102 and a Siemens Gigaset SL75 WLAN (wireless SIP phone). I managed to get it all working with my asterisk 1.4.0 installation, but I'm seeing some interesting things with the canreinvite option that I can't explain,

I am able to transfer a call to call parking using '#' without any problems since I have the 't' option in my Dial() line. However, if no one picks up the call after it has been parked and a timeout occurs (such that the call is returned back to the original extension), the call is no longer transferrable afterwards. Can anyone suggest how to fix this problem so that I can