similar to: TDM400 audio problems

Has anyone on this list succesfully managed to get two (or more) TDM04 (with four FXO each) working on a Dell PowerEdge server? If so, which model? Was it a hassle? I'm doing a seven-line installation and a callbank seems like overkill, I just don't want to get suck with a PowerEdge that gets into an IRQ mess. Thanks in Advance, Tom Hayden

I have tried installing many of the beta versions and most of the release versions of 1.8. I have 3 SIP phones which we use for all our calls. After installing 1.8 the first thing I try is calling out port one of my Digium TDM04 back into port 2. I can see that the call comes in and tries to call all three SIP phones but the phones never ring. Eventually the call goes to voice mail and these

I am getting the following warnings on the CLI when loading Asterisk 1.6.1-rc1: [Feb 12 12:32:34] NOTICE[22261]: timing.c:59 ast_install_timing_functions: Multiple timing modules are loaded. You should only load one. [Feb 12 12:32:34] ERROR[22261]: codec_dahdi.c:398 find_transcoders: Failed to open /dev/dahdi/transcode: No such file or directory [Feb 12 12:32:33] WARNING[22261]:

Hello everyone! I'm planning on setting up a new system shortly and can't pick the right card... We will have 2 or 3 lines coming in and 7 extensions (GXP2k's). Should I just get 2 or 3 X100P cards? Or do I need the Sangoma A20200 or even the A20200D (Echo cancelation)... I was thinking I'd use a Dell 2.0 GHz machine as the server... If anyone has suggestions as to

I currently have some Asterisk home servers on general pc hardware as well as a mission critical server asterisk pbx running on a Dell 2850 To reduce noise and power consumption i would like to migrate them all to an Intel Atom based solution, showstoppers so far were single NIC and single PCI slot motherboards. I found that Supermicro makes a Dual NIC board with one PCI slot and 2

Hello, After solving the other "low hanging fruit" audio issues in our Asterisk PBX, we are left with occasional cases of severe echo which we have not found a solution for yet. Our system: - Asterisk 1.2.0-beta1 - TE110P on a PRI - TDM04 and TDM40, but these are unrelated to current echo issues - Fedora core 3 - Echo canceller KB1 Most calls have minimal, acceptable echo levels. But

Hi, I have a FAX machine connected to a TDM400 card FXS port. When I receive a fax call through X100 and transfer it to that extension, the FAX machine display REC, but nothing happen (no fax received). There is something special to be done for this configuration? Thanks, Dan

Send Asterisk-Users mailing list submissions to asterisk-users@lists.digium.com To subscribe or unsubscribe via the World Wide Web, visit http://lists.digium.com/mailman/listinfo/asterisk-users or, via email, send a message with subject or body 'help' to asterisk-users-request@lists.digium.com You can reach the person managing the list at asterisk-users-owner@lists.digium.com

so i have been running v1-0 on all of my test boxes for about a month now testing iax/sip/res_xxx. I decided to put it into production so I updated a box that was running 0.9.? that had been working perfectly for months and low and behold the inbound line from telco now intermittantly doesn't clear and none of the other channels can dial out on that line. I have tested the line in this

-----Original Message----- My question concern outgoing calls. How can I configure my extensions.conf to get a PSTN line on my TDM04B card in the following order : first trying on the channel 4 then if 4 is busy then switch to 3 if 3 is busy then switch to 2 and if 2 is busy then say there's no more line available. I don't want to dial on the first channel as it's my main number

Hi, I have got my Asterisk server running with TDM400 card (2xFXO & 2xFXS). I originally had the system configured with a Panasonic fax machine on one of the extensions. Due to the high volume of fax spam, I figured it would be a much better idea to capture the faxes as TIF or PDF files to minimize wasted paper, etc. I have downloaded, compiled and installed spandsp and can see the rxfax

hello all- has anyone had any problems with the handsets on BT100's. Just picked one up for my lab and the speakerphone works great but I am only getting one way audio (incoming) from the handset. Since the speakerphone works fine, I can't think of any config. reasons why the handset wouldn't other than a faulty handset. Any thoughts or experiences? Jason Kawakami Technical

----- Original Message ----- > From: Greg Hill <gregh-asterisk@hillnet.us> > Subject: Re: [Asterisk-Users] New to * > To: Asterisk Users Mailing List - Non-Commercial Discussion > <asterisk-users@lists.digium.com> > Message-ID: <Pine.LNX.4.44.0409031231070.1975-100000@hillnet.us> > Content-Type: TEXT/PLAIN; charset=US-ASCII > > On Fri, 3 Sep 2004, Bill

----- Original Message ----- > Message: 3 > Date: Thu, 16 Sep 2004 07:57:15 -0400 (EDT) > From: David Troy <dave@popvox.com> > Subject: Re: [Asterisk-Users] No Caller Name sent from Asterisk over > National or DMS100 PRI to a Norstar MICS? > snip> > > I have a PRI link up and running between Asterisk and a Nortel Norstar MICS > > v4.1 . I'm having a

Back in the office post-astricon. 1.0.0 running in the lab. YIIIIIIIHAAAAAAAAAA! THIS GUY!!!! rocks. Thanks to Mark for *, Steve and Olle for the conference and to ALL community members. Everyone using * is contributing in one way or another. See y'all next year Jason Kawakami www.optellabs.com

----- Original Message ----- <snip> > I've downloaded the * software and the zaptel drivers. look in the zaptel source directory and you will see a file called README26 (i think, or something like that) i am not a linux expert but my linux 'experienced' partner told me something about the 2.6 kernel... > > And now, to be quite honest, I haven't got much of a clue

Hello all- Playing around with res_odbc (thanks bkw) and have successfully gotten sip.conf to run but am having difficulty with voicemail.conf and extensions.conf. I used the load_res_config.pl script for each one and all of the data seems to be in the DB but * doesn't seem to see anything after a reload even though it is acknowledging a load of x.conf (where x is extensions/voicemail)

So I have a route with [1-9][0-9][0-9][1-9][0-9]* as a base route that should match NXXNX. Right? I built another route 01144[0-9]* that I thought would match 01144X. and send the call to the UK but the script is matching 01144207108???? With the first route. Can someone smarter than me help with some samples? Please? If I can get one for 1NXXN. and 01144. I should be able to figure the rest

-----Original Message----- > -this is very true, however, the current version of the Axxess software > (9.0) supports SIP trunking natively on the IPRC. I just got my Axxess > upgraded and am salivating to get * connected to it. Hmm, so 9.0 is out and it supports SIP natively. How did you plan to integrate the 2? -The Axxess will see the * as it would see an IP service provider.

What are peoples experience with the reliability of the TDM400p. Specifically in the 2 FXO, 2 FXS configuration, which is the 022 (?) model. Is this board prone to random failures? joe a.