similar to: Wildcard X100P or TDM400P?

I've just moved into 3.3v PCI servers and found that my clone X100P cards were lying about the 3.3v supported notch. Can I use a Wildcard TDM400P without any modules as a timer for MeetMe in a 64 bit 3.3v server? Will I still need to plug the hard disk power cable into it? Is there a better cheaper 3.3v MeetMe timer? (Boss doesn't trust the kernel timer.) -HJC

Hi All, I'm attempting to use two X100P cards and one TDM400P card. What driver do I load for the TDM400P? Is their any documentation for this card yet? Also, I know this has come up before but I can't seem to find it in the archieve... how do I configure the second X100P card? Anyone have a working sample? Thanks in advance, Randy

Hi, I'm thinking of purchasing a TDM400P card and was wondering if anyone has experienced any echo issues with phones off these cards connecting to the PSTN via the X100P cards? I have had my fingers burnt with a Voip phone > X100P. Cheers, Taff. --------------------------------- ALL-NEW Yahoo! Messenger - sooooo many all-new ways to express yourself -------------- next part

With one IVR payment system, I noticed quite a difference in DTMF transmission between these two cards. The IVR missed nearly all digits from X100P, while receiving digits from TDM fine. Since neither card process or synthesize audio, what can the difference be? (This particular IVR has problem with some regular phone devices, too.) Yuan Liu

Hello. I've seen several posts talking about line quality using Digium cards that are sharing IRQs or on machines where X is running but after trying all of those fixes I am still having a problem with line static on outoing calls. BTW, calls that are from one extension to another extension have no static, however, they have occasional clicks and pops. At any rate, I was wondering if

Hello. All. I am a bit new to asterisk, started from half a month ago. I am setting up a home asterisk server with analog card. I am using asterisk 1.4.27. At the moment, I bought a X100P card and installed it on my computer. I used it to connect my home phone line. For the moment, it works fine when dial in. Soon I noticed when I dial out through it to my mobile, it can't hang up

Hi. Please excuse me asking this again. But it really puzzles me. We're installing asterisk at a branch office at NJ (HQ is at Petach-Tikva) It'll need to support 5 POTS lines, 11 analog extensions and four VOIP phones. I wanted to go with a T1 card from digium and a channel bank, but we have a dead line. It has to be up and running by January 1st. I don't have the time to start

Hello I setup Asterisk@Home with purely VoIP and it worked fine. I then added an X100P card so I could call out / take inbound calls via PSTN and that went fine. But I have just added a TDM400P card (specifically a TDM30B) and now problems. Here is some of the output. Any ideas on what I should be looking at next? When I run genzaptelconf -s -d I get lots of erors on screen - bit I can

Hi All, Sorry if this has been around a millions times.. I have been off this list for a few months now.. I have installed the latest asterisknow (upgraded asterisk to 1.6 as well) and I am having a hard time getting my X100P and TDM400P working.. Its all new to me with dahdi because my old server is still running Asterisk 1.0.2 so there have been lost of changes.. Can someone point me in

Is the Wildcard X100P still supported? I have one sitting around that I bought 3+ years ago and never used it. I need the functionality now. Before I run off and buy something new, I'm curious if this will "just work". I also have an old TDM400P with 2 FXS modules that I bought at the same time. Then, there was no FXO module for the 400P. Will a TDM400P this old support a

I've searched the Wiki and this forum with little success. I have a TDM400P in my server which functions fine. Except it will continue ringing about 3 times after hangup. I.e. it's failing to detect the hangup tone. I was previously running a Sipura 3000 and had the same issue. After researching and some timely assistance I was able to determine the hangup tones applicable to

Hello. Well I finally rx'd my dev kit (new batch of TDM's apparently. I'm on Mandrake 9.1 There were no hardware install instructions, it would have been nice to know whether the 4-way power connector was to be used or was for some other future or expansion purpose. It came with a floppy disc, no label and it wasn't even write protected. The only readme file was

I am sure that quite a lot of people would like to have Caller ID working with their X100P and TDM400P cards outside of USA. Judging from previous threads this is just a matter of implementing this support in the software driver! So, I was thinking, if we get together and put few $(USA DOLLARS) into a basket, we could then ask Digium to actually properly implement Caller ID for non USA

Hi, after finally getting my testsystem to work well I'm planning to buy some hardware. Now I was wondering what the advantages / disadvantages of using a Wildcard TDM400P solution over using real sip phones like the snoms is? The only thing I came up with is that the Snoms can use a LDAP adressbook on the server. What about calling a sip adress like person@server.com. Can this be done by

Now that the X100P is no longer being offered by Digium, what is the best solution? I seem to have run into a few posts where people talk about problems they've had with their X100P clone cards (dropping calls, echos, etc) other people seem to not have any problems. Of the three chipsets that will work: Intel 537EP, Ambient MD3200, and Motorola 62802 (as seen here

Hi, I had ordered a TDM40B and developers kit a few months ago. I have everything installed and working, with one exception - sound quality. When placing a call it sounds like a very bad cordless phone - lots of hiss / static in the background. This even happens with the dialtone, though it is much worse one the call is connected. This does not occur when the phone is directly connected to the

Yo all, I have a problem with a Dutch (KPN) PSTN-line, connected to an X100P. The call wil sound OK at first, but after 10-20 minutes, the audio will start to crackle. Soon after that, this crackle turns into a continuous noise and the parties won't be able to hear eachother anymore. It also sometimes happens that the party on the TDM400P hears a very loud, short-delay echo of themselves,

Hi I thought this might be of general interest. Recently I purchased an X100P from a Digium reseller in the UK. Very pleased with the card; works perfectly. My friend (known for his deep pockets and short arms) purchased an X100P card from Ebay. He's had no end of problems with line noise, dropped called etc so I thought I would compare the two cards. Plus mine was delivered within two

OK, I've spent way more time than I wanted to on getting an x100p clone to work in Australia. I'm happy to consider other (more functional) options. Does anyone have an opinion on both the Sipura 3000 and other Digium cards (like the TDM400P)? I need something that works with no much fuzz. I know the Sipura 3000 is cheaper the the TDM400P card. All I need is to channel my POTS line

Hi! I have just bought the X100P and TDM400P cards to install on my computer to implement the PBX. I also downloaded the newest softwares asterisk_ver0.5.0, libpri_ver0.4.0, and zaptel_ver0.7.0) to install on my computer (Red Hat Linux 8.0). All packages are compiled well. When I use "modprobe" to load drivers (modprobe zaptel, modprobe wcfxo, modprobe wcfxs), the first two (zaptel,