Displaying 20 results from an estimated 9000 matches similar to: "Call Waiting Audio Prompt"
2010 Jul 28
1
Why do Zaptel calls drop all of a sudden? Could busy detect be the problem?
Hi Guys,
I am getting a complain that call on analogue lines (Sangoam A400D) drops
all of a sudden. Here is what I see in logs:
[Jul 28 15:49:08] DEBUG[21438] dsp.c: ast_dsp_busydetect detected busy,
avgtone: 75, avgsilence 135
[Jul 28 15:49:08] VERBOSE[21438] logger.c: -- Executing
[h at macro-dialout-trunk:1] Macro("SIP/2111-b6a400b0", "hangupcall|") in new
stack
[Jul
2012 Oct 01
9
How to remove the call waiting tone without disabling callwaiting?
Hi,
The call waiting tone is very annoying (you hear nothing while it plays
the beep). I need callwaiting because of the queues (the phone has to
ring as soon as you hangup) but I want to remove the beep on my dahdi
channels, how can I do?
Thanks,
Niccol?
--
http://www.linuxsystems.it
2003 Nov 03
4
Call waiting on X100P
I have Asterisk setup in a SOHO environment.
I have 2 X100P cards at Zap/1 and Zap/2.
I have 1 TDM400P card with Zap/3 - Zap/5.
I have subscribed to callwaiting, callerid and calleridcallwaiting from
Qwest on the 2 PSTN lines - Zap/1 and Zap/2.
My problem is when I'm in an active call to the outside thru Zap/1 or
Zap/2, I can't pickup the incoming callwaiting call. I can see the
2008 Nov 11
1
What makes TDM400 FXS Connection to TELCO go into Off Hook State?
I've been having trouble with making outbound calls to my
TELCO from a TDM400 card (FXS KS signalling) after upgrading
from 1.6-beta9 to 1.6.0. The problem is completely intermittent.
When it fails, I get this message:
[Nov 9 19:12:26] WARNING[18916] app_dial.c: Unable to create channel of type 'DAHDI' (cause 0 - Unknown)
At some point, it starts working, but I don't know what
2004 Aug 11
1
CallerID Debug On Zap/POTS Channel
Hi all,
I've been trying to wrap my mind around this one for several days now.
How can I 'debug' the CallerID reception on a Zap/POTS channel? I have
a POTS line with CallerID and a Digium TDM11B card right now. I have my
signalling set to ks for both sides, can make and receive calls just
fine. But I never get CallerID on incoming calls. I get the following
messages:
Aug 11
2003 May 01
1
Youch! Painfully loud beep...
I just called 6610 from Zap/1
exten => 6610,1,Dial,Zap/1&Zap/2
(Don't try this with the handset pressed up against your ear) ...is this the
call waiting indicator? Is it a file, can it be turned down - and does it
get used anywhere else?
These are both fxs ports. In zapata.conf changinging to callwaiting=no stops
this. The text implies that this affects fxo ports.
John
This e-mail
2005 Jan 27
1
TDM-400P + CallerID
Hi,
I'm just starting out with Asterisk, in combination with a TDM400,
filled with 2 FXS on channels 1 and 2, and 1 FXO on 4. Having just
started, all I want right now is to be able to answer incoming calls on
a phone connected to channel 1. The trouble is the caller id. I have
caller id enabled on my line, my phone supports it, and when I connect
the phone directly to the line, it works.
2009 Jan 16
1
Voicemail message is dialtone
Hello all,
I have one Asterisk 1.4.21 system connected to a North American POTS
line. Normally hangup detection works fine, and Asterisk hangs up
properly if you are talking to a caller and they hang up; but
occasionally a call comes in (typically from a US telemarketer) where
the caller hangs up just as voicemail recording is starting, and you
get a voicemail recording of dialtone (then
2004 Sep 29
3
Calling Waiting on PSTN line
I have looked through tons of wiki etc and still have not found an working
answer for this. Does Asterisk support call waiting on a PSTN line(through
an X100P card). I hear the beep but I can't get it to flash to the other
line. Anyone with a wokring configuration, PLEASE, send it along.
Thanks
Martin
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
2004 Sep 28
1
Help with Call Waiting!
Help! I am having a problem getting wall waiting to work.
I have a X100p and a TDM400 card with and analog phone attached (as well as
a number of SIP phones) running on RedHat 9.0 box. The PSTN line has the
call waiting feature. If I am on the phone, I get a beep indicating a second
call is waiting. However, there is no way, no how, that I can get it to
switch to the second line! Flash button,
2010 Jul 14
2
beeping during call
Asterisk 1.4.32
dahdi-2.3.0.1
Centos 5.5
Digium TE420
CAC channel bank (2)
Cisco RVS4000 router
Cox 50 Mbps/ 5 Mbps cable modem
Flowroute provider
codac G-711
90 % CPU idle
callwaiting=no
When there are 10-15 or more calls up the farend hears a callwaiting
like beep every 3 to 6 sec. the duration of this "beep" is very short
and would be no problem if it didn?t happen every few
2004 Jan 08
1
Strange Call waiting problems - SNOM 200 & Grandstream Budgetone
Hi
I am setting up an Asterisk System in an office environment, Incoming and
Outgoing calls are working ok, but i am having a few strange problems
regarding call waiting.
With the SNOM 200 (firmware 2.02t) phones, if you are on a call and a 2nd call
comes in, the call waiting beep is played and the light flashes, but if you
hang up the 1st call, instead of the phone ringing, it connects the
2010 Mar 04
1
No Audio on pstn call
Hello,
I'm facing problem where as whenever there are incoming call from
pstn, there will be no audio coming in. User at the other end also
could not hear my voice. This happens few days back. Im using asterisk
1.6.1.2 with dahdi tool 2.2.0.
I thought it was time to upgrade, so upgraded to dahdi 2.2.1 and
asterisk 1.6.2.5. However, it does not help at all.
My current config as follows :-
2003 Aug 22
6
Caller ID problem
So I'm not getting caller ID via the X100P
card. I've confirmed the PSTN is sending
me caller id by plugging in a little third party
box.
Ideas, tips, greatly appreciated
2003 Dec 06
3
CallWaiting CallerID
Hi all,
In order to get the CallerID from PSTN (X100P) I have modified callerid.c
file like that:
callerid.c [line 256]
from:
case 3: /* Number (for Zebble) */
to
/*case 3: Number (for Zebble) */
Without this modification my own number was displayed as the inoming call
CallerID.
Now I want to go further.
I have activated CallWaiting support on the POTS line.
When someone calls and I am in
2003 Nov 12
1
X100P random hangups.
I have a couple of X100P's in my system and while on calls they just randomly hang up for no reason.
I have tried messing with the busydetect and callprogress setting them to yes and no same and still random hangups. Is there another setting I should be looking at?
My zap config looks like.
context = inbound-work
include => extensions
signalling
2004 Apr 05
3
Buzzing on TDM400P FXS?
I have an intermittent problem with the one FXS line that I have. On
most calls, the first ~5 seconds of the call has a loud buzzing noise
on the line. After 5 seconds or so, it fades off to nothing, and the
sound quality is great. Searching for "buzzing" on the list doesn't
give a whole lot to work with. The buzzing happens on calls that are
routed over both my FXO line and
2007 Nov 30
2
My AsteriskNo unable to registration
Dear The Expert,
I am very new with this, I have installed AsteriskNow, X-Lite as my
SoftPhone, I am using SPA-3102.
I have 3 extensions,
me at 250, 998 is my Linksys SPA-3102 and 999 for PSTN Line (see below)
My problem is, I am unable to call 998, I thought this is registration
problem, (because the Linksys screen info said Registration Failed)
Could any body please help?
Many thanks in
2011 Jan 24
2
Outgoing FXO calls have no audio with callprogress=no
My outgoing FXO calls are answered but have no audio in either direction
if I have callprogress=no in chan_dahdi.conf. If I change to
callprogress=yes then the audio returns. My chan_dahdi.conf file is
listed below. Can anyone point-out why callprogress=no isn't working?
#cat /tmp/a
[trunkgroups]
[channels]
language=en
context=incoming
toneduration=40
;usedistinctiveringdetection=yes
2004 Aug 28
5
Distinctive ring detection problem
I am trying to get distinctive ring to work on my PSTN with no luck.
I can get 2 different ring codes but it skips the context assigned...
here is my complete zapata.conf:
[channels]
signalling=fxs_ks
usecallerid=yes
rxgain=1.0
txgain=1.0
language=en
context=default
usedistinctiveringdetection=yes
dring1=134,0,0
dring2=137,0,0
dring1context=internal2
dring2context=default