similar to: T100P + Adtran TSU600 + FXO and caller id problems

Hello, Did anybody successfully tried upgrade Adtran TSU 600 to firmware which is working properly with T100P and asterisk ? B.

Hello, I have just received Adtran TSU 600 with 24 FXS ports. I have installed sucessfuly T100P card. Adtran is connected to t100p with crossover T1 cable. On T100P card I have a green light and on Adtran I do not get any errors or alarms. But I do not get dialtone on FXS ports. Adtran is configured: For Network Timing, fxs ports ore fxs_ls on Adtran. In zaptel.conf: span=1,1,0,esf,b8zs

I am sending a call down a E&M wink trunk to a adtran tsu600 channelbank. The extension is setup like so... exten=>799179,1,Dial(zap/g2,20,D(9179)) exten=>799179,2,Hangup() It should Dial the Adtran and send some DTMF signals to a telephone on an fxs module in the Adtran. Asterisk is seeing the call answered when the T-1 is picked up by the Adtran not when the ringing phone is answered.

I have just received a T100P and an Adtran TSU 600 in the mail. I seem to be having a problem with the T100P card. So far I have done the following: vi zaptel.conf fxoks=1-22 fxsks=23-24 ... vi zapata.conf ... signalling=fxo_ks ... channel => 1-22 ... signalling=fxs_ks ... channel => 23-24 I then run modprobe zaptel modprobe wct1xxp ztcfg -vv There are no errors to report. In

I have a T100P card connected to an Adtran and then a T1. I have added the following configurations to Asterisk...but, when I dial 9 and then a local phone number, it bounces between the dial tone and silence and the *error* light on the Adtran blinks. zaptel.conf span=1,0,0,esf,b8zs fxsks=1-8 loadzone=us defaultzone=us zapata.conf [channels] context=from-sip signalling=fxs_ks

Hello all, I've got a T100P connected to an Adtran TA750 with a T1 crossover... This connects to a patch panel with phone ports. The Adtran is fully populated with FXS cards. All I get on any phone port is a fast clicking noise... No dialtone. Asterisk 'sees' the card, (the channels show up in /proc/zaptel). Incoming calls are routed to the zap/x channel, but no ring. I'm

Can I configure an Adtran channel bank with a mixture of FXS and FXO cards and have them come into a single T100P T1 card? It seems like this would be a cheaper solution than trying to load a bunch of PCI cards into a PC. Also, when shopping for an Adtran (on ebay) - what do I need to watch out for as far as interfaces or capabilities to make sure that it works with a Digium card?

I've been working with an adtran ta 850 hooked to a t100p pretty much all day today, and I haven't gotten past configuring zaptel.conf and zapata.conf. For some reason, when I pick up analog phone hooked up to the first module of a quad fxs card in the second slot of the ta 850, asterisk thinks that all four of the fxs modules in that card are going off hook. If I pick up a phone hooked

Hello, So all the pieces are finally here, and I'm ready to play. I remember reading on this list that the connection Channel Bank <-> T100P requires a "reverse cable." Is this a regular Ethernet reverse cable (i.e., only a couple of pairs reversed?) Please help me before I blow something up! Saludos, Jose.

Jay, I have had a lot of trouble with the FXO ports on Adtran TA750. Unless the incoming POTS lines have a balance impedance, they will buzz very bad. Gregory P. Scasny Golden Technologies Inc. http://www.golden-tech.com 219-462-7200 -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Jay Milk Sent: Sunday, April

Hello Can somebody send me please config files of zaptel.conf and zapata.conf for adtran fxs ports. I cannot make it work. I do not get a dial tone on Adtran and when I am trying to call from sip i get: app_dial.c:674 dial_exec: Unable to create channel of type 'Zap' == Everyone is busy at this time There are no errors on T100P and adtran. Please help! B.

Skipped content of type multipart/alternative-------------- next part -------------- No virus found in this outgoing message. Checked by AVG Anti-Virus. Version: 7.0.298 / Virus Database: 265.6.4 - Release Date: 12/22/2004

I am having a problem using the Adtran 750 FXO quad card with a Groundstart trunk line. I am able to receive calls on the trunk line, however dialing out is not working. The Adtran does not seem to be doing the signaling. Has anyone used the 750 FXO card in Groundstart mode? Any special configuration issues that I should be aware of? Syed Akbar Alico Systems Inc www.alicosystems.com Tel:

My carrier tells me our Adtran is seeing error seconds and timing slips. Is there any way to check this on the T100P, maybe in /proc? Craig Bruenderman Network Advocates, Inc. 300 Envoy Circle Suite 300 Louisville, KY 40299 Main: 502-412-1050 DID: 502-992-5929 Fax: 502-412-1058 Mobile: 502-548-1100

Hi, Maybe someone has seen this before... I've installed a new T100P, but it doesn't seem to work. I've attached the T100P to an Adtran 750 using a crossover cable. The Adtran shows a red alarm on the T1 interface. The Adtran has been set to factory defaults with FXS cards in 1-3 and an FXO card in 5. The T100P shows no signs of life--the leds are not lit. Should I be seeing

Hello, I new to this, but with the help of mailing lists archives and IRC I am able to build my PBX. Thanks to all who had help me to reach till here. I am stuck at a point where I can't find the solution on mailing lists or even on IRC. I have individual 4 DID (Direct Inward Line) coming from Telco and terminating into TA 750 to FXS card. Many of them told that Phone instrument terminates

It is possible to connect ADTRAN TSU 600 VP24 FXO 24 Port Channel Bank to Asterisk ? Somebody offered me that hardware, but I do not know if thats good hardware for Asterisk. rgs, Bartosz -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20030820/4a9e4608/attachment.htm

Hello All, I could use a recommendation if anyone has a moment. I have the T100P but I have not gotten my service yet. I want to have at least 12 lines of digital voice with DID. Should I just seek out a PRI ISDN provider or is there something else I should look for? I want to keep cost as low as possible. Also, I want to own my own router for the phones since it is always a hassle to get

Here is some more stuff to add to the confusion about the "callprogress" option. I currently have my * system operating with a T100P talking to an ADTRAN TSU600 channel bank with 8 FXO ports connecting to the outside world and Grandstream SIP phones as handset extensions. At first I naively set "callprogress=yes" in zapata.conf. The results were typical of what many

Hello, I have a T100P card on a Red Hat 8 machine with Asterisk installed on it and I'm trying to get the data routing properly through it. I purchased an Integrated Data/Voice T1 Line with channels 1-6 voice and 13-24 data. The line is plugged directly into the Asterisk machine's T100P card. Previous to the asterisk set up we had an Adtran router that connected everything to what the