similar to: Sipura 3000 inbound FXO problem

The below is a asterisk message when I try to call from a callerid blocked phone into a SIP (Sipura 3000) FXO gateway - and I have not consciously put any restrictions on incoming calls... Dec 29 10:23:44 NOTICE[2745]: chan_sip.c:7486 handle_request: Failed to authenticate user WIRELESS CALLER <sip:A714XXXXXXX@1.0.24.5>;tag=1a6833c3913bcb6o1

I am trying to configure the FXO port on a Sipura-3000 for use with Asterisk. When I connect to the Sipura to dial out on the PSTN line connected to the Sipura's FXO port, it gives me the dialtone of the PSTN line and then I can hear the DTMF for the number I dialled beforehand. It does work but the customer perceives this delayed second DTMF feedback as "unprofessional" and the

Does anyone have a Sipura 3k running, and using the FXO? I've got things working right, but if I try to toss a *67 in the dialplan, it seems the sipura is throwing a 403 forbidden back. For example: exten => _91NXXNXXXXXX,3,Dial,SIP/sipura1pstn1/${EXTEN:1} works fine exten => _91NXXNXXXXXX,3,Dial,SIP/sipura1pstn1/*67${EXTEN:1} does not (even if I toss a couple Ws in) I can't

My apologies for the off-topic post ... No matter what settings I try, when I dial in to the SPA-3000 on the PSTN line, it picks up the call and immediately gives me a fast busy tone then hangs up. The info tab says under PSTN Line status: Last PSTN Disconnect Reason: PSTN Disconnect Tone which seems to indicate that the SPA thinks the caller has hung up. Since I am in Japan, it is possible

I am considering using Sipura-3000s as FXO devices for my * system. Has anyone tried them in that configuration? They interest me because they need no PCI slots and therefore no drivers. I would much prefer not to have any special kernel requirements for my system. /carmi

Anybody using a Sipura 3000 for FXO with Asterisk? Mine is working except for one small nit... When a call comes in from the PSTN, the Sipura answers it and then passes it on to Asterisk, which plays extension ring tone. I'd prefer for the POTS line to stay on-hook while the extension rings, and to only be answered by the Sipura when the extension answers. Has anybody made this work?

I am trying to get a SPA-3000 to work behind NAT - for the sake of the exercice. The SPA is on the local network at the address 192.168.0.125 behind a NATted linux router. The machine I am trying to work with is a friend's (let's call it lolo.dyndns.org) and I've installed Asterisk 1.0.3 on it. I can see the SPA register but when I try to make an outbound call I get the message:

All, I am looking at a little support on this, as I haven't found it on google yet. I have had this work on Callweaver, but am moving to Asterisk for a variety of reasons. My dial plans, and everything else transferred perfectly, though I am not sure they are 'correct' for Asterisk 1.6.1, with simple things like SIP users outlined in the sip.conf file, not in the users file,

I have a sipura 3000 that I am using just to send calls to my mac asterisk server. When you call the phone it rings, answers, and then goes right to a busy signal. Any ideas? Thanks for your help! Jane At the console in verbose mode I get: *CLI> DEBUG[8501248]: File chan_sip.c, Line 663 (create_addr): Setting NAT on RTP to 0 DEBUG[8501248]: File chan_sip.c, Line 554 (__sip_ack): Stopping

Is there any support in Asterisk for encryption of IAX and/or any other VOIP protocols? I haven't seen anything on this in the wiki or on the list. Just curious.

Hi, the topic says it all really. Does the Sipura 3000 detect and report UK clid correctly? thanks Mike

Hi all, Anyone able to remotely reboot their password protected Sipura SPA-3000 from command line. I am trying: Sipura SPA-3000 from command line: # wget http://admin:mypassword@192.168.1.55/admin/reboot The strange thing is it works fine when I go to http://admin:mypassword@192.168.1.55/admin/reboot with my web browser... Thanks....

Hi We are getting more and more email from Mac users asking how they can connect their MacOSX based Asterisk server to a PSTN phone line. This has led to two ideas ... 1) Mid term: set up a donation fund to sponsor the development of Zaptel drivers for MacOSX Note: if everyone who downloaded the Asterisk installation package for MacOSX during the last two months since its release would donate

Hi all, We have several sipura 3000's working well for outbound calls, however the issue we have is that when calls are sent to the Sipura with Dial(SIP/${EXTEN:0}@sipura1) the Sipura does a SIP answer immediately and then proceeds with the call "in band" therefore sending dialing sounds back to the caller. Other SIP gateways we have notably the Vegastream and others do not do a SIP

Folks! I discovered some serious problem with several Sipuras 3000 but I don't know if the problem is with them or Asterisk. Basically, if I call a Sipura PSTN line, when there is a call already in progress, generally I get a 503 Sevice Unavailable, but if I try hard enough, I am able to get through and connect to dialed number. The other call gets disconnected but the originator of the

Hi I wonder whether anyone got the Sipura ata 3000 to decode British Telecoms callerid and pass it to asterisk? The userguide seems to suggest that this is not possible, is that right? Conrad

Hello, I'm configured Sipura-3000 to forward IP calls to PSTN number on no answer (In User1 tab Cfwd No Ans Dest: 123456@gw0) IPPhone ---IP---> Sipura-3000 ---PSTN---> PSTN User Generally it works fine, but Sipura sends back SIP OK to IPPhone just prior to dialing to PSTN number. How to configure Sipura to detect that the remote side on PSTN picks up the phone and only then to

Hi List, I hope this setup must be done by our astersik users.. I am using Sipura 3000 to receive PSTN calls and forward those calls to asterisk for voice processing and after that, I am transferring call to extension through FXS port on SPA 3000. Currently, media of call is trombone through asterisk. i.e achieving blind transfers on asterisk with SPA 3000. Is it possible to stop trombone

I can not make a "call pickup" to work with Sipura-3000. I have one SIP phone and one is connected to ATA Sipura-3000 I've in all sip.conf context callgroup=1 pickupgroup=1 in features.conf I've tired: pickupexten = *88 pickupexten = *8 Nothing works. What am I missing? -- #Joseph

Hi, I'm looking for a full list of xml provisioning variables of the SPA-2100/3000. Currently the Sipura website has example XMLs only for the SPA-841 [1] and SPA-941 [2]. I'm mostly interested in the CallerID type selector variables and whatever variables control the PSTN<->VoIP settings. Sipura Configuration website form field names are numeral only. :( [1]