similar to: ISDN4Linux Incoming calls

Well, it has been a long time since I used my NetJet S cards with asterisk (moved to the quad PRI card) but I am trying to get this working again for home use. Basically, what I am using is this: Linux 2.6.8.1: config lines: # ISDN subsystem CONFIG_ISDN=y # Old ISDN4Linux CONFIG_ISDN_I4L=y # CONFIG_ISDN_PPP is not set CONFIG_ISDN_AUDIO=y # CONFIG_ISDN_TTY_FAX is not set CONFIG_ISDN_DRV_HISAX=y

The card is an ASUSCOM ISDNLink PCI (passive) and the circuit is from Qwest (in the US). I will be using this circuit only for voice (I'm doing this because of the poor quality of my POTS lines). I've compiled Hisax (as a module) into my 2.4.25 kernel, and with 'modprobe hisax type=35 protocol=4 id=hisax' I get the following: Apr 7 10:34:24 dev kernel: HiSax: Linux Driver for

Hi, Apologies in advance for the lengthy email. I'm new to asterisk and have trouble with isdn4linux. The setup is very basic like this: winxp ------- asterisk -------- winxp x-lite | x-lite | pstn The hardware involved is: Compaq EVO with RH9/kernel 2.4.20-30.9. Fritz!Card PCI v2 Asterisk CVS-04/17/04-21:36:18 Basically

I'm trying to get a basic Asterisk configuration together for ISDN incoming / outgoing calls. I have two Cisco 7905g phones working (at least talking to each other) and have purchased a NETjet-S PCI ISDN card for routing calls to / from ISDN. The state I've managed to get it to is:- -- Executing Ringing("SIP/PHONE2-d557", "") in new stack -- Executing

hi I have a passive isdn port configured in modem.conf in extention.conf i use this two channel (ttyI0 and ttyI1) with the string: exten => _NXXXXXXXXX,1,Dial,Modem/g1:${EXTEN}|60|r how can i hide my msn? is it possible to activate the clir with the @ before the ${EXTEN}? thanks Cristian

Hi, I am using Asterisk on a DSS1 ISDN-BRI with ISDN4Linux (and a Fritz Card PnP). The ISDN-BRI is in PTP-Mode (Point to Point "german: Anlagenanschluss") which is enabled within I4L with "hisaxctrl fcpcipnp0 7 1". Everything works fine except that I can not see the called number/MSN of incoming calls within Asterisk and because of this I can not route incoming calls

Hi all, I'm playing with Asterisk and I've already configured all needed .conf files. It works quite well, but now I need your help to tune the system: when I place a call from a softphone to the PSTN, I can't hear directly Telco's tones and I can't use its services, e.g. a mobile's answering machine. I don't know if I have to modify the dialplan or if it depends on my

Hello all, I currently have an Eicon Diva Client isdn card using i4l. Outbound dtmf doesn't work (and never has), but there has been an annoying problem with false dtmf detection in calls (that could be triggered easily by blowing into the receiver on the remote end). I looked through the list and found two patches that need to be applied - 1 to isdn_tty.c in the kernel, and another to

Hi all, this is a rather "newbie-oriented" question, so please bear with me... The system running Asterisk has been provided with an AVM FRITZ!Card PnP. SuSE Linux 9.0 recognizes it right after booting the system and it seems to be configured (MSN) correctly... The hwinfo looks like this: --- pbx:/etc/asterisk # hwinfo --isapnp 11: ISA(PnP) 01.0: 10300 ISDN Adapter [Created at

Hello! Im pretty new of asterisk world: my goal would be using iaxcomm to call ppl over POTN. Yesterday i configured asterisk to be able to hear a song (with Playback() command) with iaxcomm, and it was wonderful. Now, today i tried to configure asterisk to use my ISDN4Linux supported card (a plain HFC card) with asterisk. i configured modem.conf this way, after reading

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I'm having some problems using the asterisk modem driver with an ISDN4Linux card (AVM Fritz). (I realise that it's better to use CAPI, but unfortunately this card doesn't have any CAPI drivers). Every so often the ISDN just stops working (it neither dials out nor accepts incoming calls). Trying to dial out just logs: --

I posted a message a little while ago but got no response (that I can recall), I've also seen other people mention this issue. Basically, when you have music on hold, it doesn't play the music on hold, the debug info shows it is starting and then stops straight away.. # My extensions.conf ... exten => s,1,Answer exten => s,2,DigitTimeout,5 exten => s,3,ResponseTimeout,10 exten

Hello, I am trying to use 2 netjet cards under asterisk and isdn4linux. I am having a hard time trying to get them to work in terms of dial out. Does anyone have a working config I could look at for even one card (tried that, not much luck either). When i dial out: -- Accepting AUTHENTICATED call from 172.16.11.2, requested format = 2, actual format = 2 -- Executing

In this message I try to summarize what I have learned in these last two weeks. My primary sources of informations were the * list archives and linux ISDN docs. I ain't no * master, so don't trust too hard. Relevant messages from the * list for the current discussion are: 009177.html 009268.html 0498.html 0849.html My setup is an Eicon Diva (HiSax: Eicon.Diehl Diva driver Rev. 1.1.4.2)

Hello everybody, I have a strange comportment with oh323 and asterisk, I'start testing asterisk but with this I can't understant plesae help me ! Thanks Eltorio ---------------------------------------------------------- 1/PB: I can't dial from a H323 extensions (registered on a GNU GK) to a Modem[i4l] line ---------------------------------------------------------- Nothing happens

Hi *, This is my first message to this list, so I hope I am not breaking any rule with my post. My question is the following: can I establish a voice connection over an ISDN interface by using a bluetooth dongle to connect to the ISDN access point? Here follow the details: I have compiled and configured asterisk. Everything seems fine except that when I configure asterisk to use the ISDN

Hello all, This afternoon I had a BRI line installed by Telstra (our telco in Australia). I'm using an Eicon Diva 2.02 PCI ISDN card with the isdn4linux driver. Incoming and outgoing calls with Asterisk work fine (and with no echo - my main reason for getting ISDN). However, I can't seem to get outgoing DTMF working (incoming works fine). I made a call from my desk phone (Cisco 7940G)

Hello List! I finally got asterisk with capi working, and its already answering my call as well! :) Now i would like to call a number from my shoft phone (kphone). This is my extentions.conf: --- [general] static=yes writeprotect=no [globals] CONSOLE=Console/dsp ; Console interface for demo IAXINFO=guest ; IAXtel username/password

Hello All, I was just after a few pointers. I have just setup my Redhat 9 linux box with asterisk. Internal SIP call working fine. My Eicon ISDN card turned up today so - plugged it in and went through the modem.conf. It reports unable to open /dev/ttyI0 The problem is I have never used ISDN with Linux - let alone a telephony app - and I have no idea even where to start. Some pointers

We have setup an asterisk box to let everybody call into the university internal network, but I get unexpected hangups when doing an outbound call from SIP to the ISDN interface, and it happens from 20 seconds to some minutes into the call. ----------the dial and the problem----------- -- Executing Dial("SIP/57966-a19d", "Modem/g1:96121||rt|") in new stack --