Displaying 20 results from an estimated 200 matches similar to: "TE110P - problem with zone from zaptel.conf"
2004 Aug 16
2
randomize Dial() target
Hi,
is it possible to randomize extension which would be choosed by Dial()?
I would like to forward phone calls to one of sales rep in randomized
way (not to harm anyone;) ).
tia
mazek
--
http://www.marcinmazurek.com/ ::: nic-hdl: MM3380-RIPE
GnuPG 6687 E661 98B0 AEE6 DA8B 7F48 AEE4 776F 5688 DC89
2004 Aug 19
1
chan_phone - compilation problem
Hi,
I have a latest asterisk cvs sources on my box, the rest of enviroment
is:
gcc version 3.3.3 20040412 (Red Hat Linux 3.3.3-7)
linux 2.6.7
and after checkout I get:
In file included from chan_phone.c:36:
/usr/include/linux/ixjuser.h:353: error: syntax error before '*' token
make[1]: *** [chan_phone.o] Error 1
make[1]: Leaving directory
2004 Aug 26
1
Wil spandsp work with i4l driver?
Hi,
will spandsp work with i4l, or should I use capi?
tia
mazek
--
http://www.marcinmazurek.com/ ::: nic-hdl: MM3380-RIPE
GnuPG 6687 E661 98B0 AEE6 DA8B 7F48 AEE4 776F 5688 DC89
2004 Aug 27
0
h323 with Fedora 2 & GCC 3.3
Hi,
did anybody managed to compile h323 channel under Fedora 2? There's only
gcc 3.3 and 3.4. Does h323 from * or opencall work with FC2 and gcc 3.3?
Anybody had similiar problems?
tia
mazek
--
http://www.marcinmazurek.com/ ::: nic-hdl: MM3380-RIPE
GnuPG 6687 E661 98B0 AEE6 DA8B 7F48 AEE4 776F 5688 DC89
2004 Nov 30
1
wanic 520 with asterisk card
Hi,
has anyone been trying to use wanic520 card with asterisk? It's E1 card,
but I can't find any info about asterisk and wanic cooperation.
anyone?
tia
mazek
--
http://www.marcinmazurek.com/ ::: nic-hdl: MM3380-RIPE
GnuPG 6687 E661 98B0 AEE6 DA8B 7F48 AEE4 776F 5688 DC89
2004 Apr 18
4
Intel 536ep as a FXO?
Hi,
I've seen some reports about ruuning Intel modem with 537 or MD3200
chipset running with Zaptel drivers as a FXO port. Did anybody managed
to set up a PCI faxmodem based on Intel536ep chipset to work with * and
Zaptel drivers?
Modem seemd to work just fine with Linux, but the driver says no;)
some more info:
Linux 2.4.26
mazuchna:~# cat /proc/pci | grep 536
Communication
2004 Apr 26
8
Intel 537ep
Owias,
The 537 is, for the most part, a drop-in replacement for the Digium card. Please search the archive and the Wiki, as there have recently been several discussions about this exact subject.
To my knowledge that is about the only modem that works, but keep in mind it is _not_ supported. That being said, follow the instructions on Digium's site for installing the X100P and you should be
2004 Sep 03
2
Using AVM Fritz!PCI as zap interface
Hello!
Is there a way to use AVM Fritz!PCI as a ZAP interface and have it
configured for ZAP channels?
Thanx in advance!
Roland Zagler
mailto:r.zagler@fog.at
@fog smart partners
2004 Mar 04
1
ioctl(ZT_LOADZONE) failed: Inappropriate ioctl for device
Well, I think I discovered even further why there is no ringback tone
available. The following message, is displayed on the console in asterisk.
ioctl(ZT_LOADZONE) failed: Inappropriate ioctl for device
Failed to register zone 'United States / North America': No data available
Looking more into it, I found that it was related to loading tones for a
particular zone. The message is printed
2008 Dec 18
1
zaptel-Error
Hello, my English isn?t very good but I try to explain my problem. Hopefully
you can understand me. :-)
I have a Linux-Server with a Digium Wildcard TE110P. I install and configure
zaptel. But I have an error when I execute ztcfg ?vv:
31 channels configured.
ioctl(ZT_LOADZONE) failed: Invalid argument
Notice: Configuration file is /etc/zaptel.conf
line 288: Unable to register tone zone
2003 Apr 16
1
New TDM400P no dialtone
Hello,
Does anyone know what may be causing this? Asterisk was built from cvs
tonight. Ztcfg also says us is an invalid tone zone. Anyone got some
information on what this is, why is it happening, and possibly some
solutions?
[root@anistonetech zapata]# asterisk -f -d
DEBUG[1024]: File config.c, Line 653 (__ast_load): Parsing
/etc/asterisk/asterisk.conf
DEBUG[1024]: File config.c, Line 653
2005 Feb 09
1
problem with running ztcfg
Hi All,
I just installed Asterisk 1.0.5, and the
installation went fine (I ran modprobe zaptel and
modprobe wcfxo). However, when I ran ztcfg I get the
following:
ioctl(ZT_LOADZONE) failed: Invalid argument
Notice: Configuration file is /etc/zaptel.conf
line 135: Unable to register tone zone 'us'
After that I ran Asterisk and it seem to started ok,
except that it won't pick up
2003 Feb 28
34
Newbie question
I have an ATA-186 in a SIP configuration (following Shawn Djernes
how-to), but I get the following error at the asterisk console when I
try to call the phone connected to the ATA:
ioctl(ZT_LOADZONE) failed: Inappropriate ioctl for device
Failed to register zone 'United States / North America': No data
available
Everything works if I remove indications.conf from /etc/asterisk -
2007 Apr 15
0
Call tranfer drops 1st. digit
Hi list,
I experiencing a strange behaviour when transferring a call. The use case is
like this:
- Incoming call from Zap/1-1
- Routed to SIP phone SIP/1001
- The called user (SIP/1001) wants to redirect the call and presses "#"
- IVR (default setup) says "Transfer" and user gets dial tone
- User dials 1002
- IVR says "No such extension - please try again"
???
It
2004 Jul 09
1
pop3 usernames
Hello,
I would like to allow users to login as user at domain.tld instead of
providing their login name; I'm coming from the sendmail/qpopper land
and am trying to migrate to postfix/maildir/dovecot one step at a time
and I've been able to find a way to do most of what I want except for
the above requirement.
Do I have to use a SQL server or is there any way to easilly map an
email
2011 Jan 24
1
custom maildir location mapping
Greetings,
I'm migrating from a sendmail/dovecot setup with system users to a
postfix/dovecot maildir setup with virtual users. To simplify the mess we've
gotten into by having users that can't remember their username, we've
switched to email address being the username. In order to allow for a smooth
migration, I need to allow users to be able to login with their email
address as
2005 Feb 10
0
Asterisk 1.0.5 won't pick up incoming calls
Hi All,
I have just migrated from Asterisk 1.0.0 to Asterisk
1.0.5 and I have an X100P installed. The old asterisk
was working, but now the new version isn't picking up
any calls! However, I did notice that after
installation, I performed modprobe zaptel and modprobe
wcfxo and they worked fine, but when I executed ztcfg,
I get the following errors:
ioctl(ZT_LOADZONE) failed: Invalid
2005 Feb 23
3
Problem connecting a TE410P to an E1/IP equipment
Hi,
I'm trying to connect a PC with a TE410P to an E1/IP equipment.
Unfortunately I keep getting a yellow alarm from zaptel (in zttool)
and a Loss of Framing alarm on the remote equipment.
The E1/IP is connected on the other side to a PRI interface on a GSM
MSC.
I have configured the span as:
span=1,1,0,ccs,hdb3 (also tried span=1,0,0,ccs,hdb3)
and the channels as:
bchan=1-15,17-31
2007 Feb 17
2
HOW to enable traceroute with IPTABLES
Hi,
I am setting up a firewall on CENTOS 4.4.
I have done default block
iptables -P INPUT DROP
iptables -P FORWARD DROP
iptables -P OUTPUT DROP
I have enabled ICMP to www.google.com
iptables -A OUTPUT -p icmp -d 64.233.189.104 -j ACCEPT
iptables -A INPUT -p icmp -s 64.233.189.104 -j ACCEPT
Ping works fine as below
[root at firebox rc.d]# ping 64.233.189.104
PING 64.233.189.104 (
2007 Jan 30
2
Accessing an external USB disk
I was able to remove the NTFS partition and repartition the HD as a type
Linux (83). Next I created the ext3 file system.
If I reboot with the USB drive attached, the boot process hangs, however
if I turn off the drive, boot and then turn it on, all is fine.
# cat /etc/fstab
shows the drive, but I am not sure how to use it for a backup nor do I
know how to access it. Any help would be