similar to: Variable substitution - How can I do Dial(${DIALSTRING}) where ${DIALSTRING} is 'SIP/201, 15, tT'?

Does anyone know how to set the music on hold class with the Manager Interface in 1.8? Here is what I am using but I end up just getting no music when I put this in place, when I remove it the default is back. The classes I am setting work elsewhere just fine. I did not include the opening of the socket, logging in etc because that's all working fine along with other things I am doing within

I have a Asterisk server (PBX in a Flash) with Aastra 57i phones. When there is an incoming call the phone will display two buttons "answer" and "ignore". If you press "ignore" the call is dropped instead of sent to voice mail. The following is the log: -- Called 111 -- SIP/111-00001c14 is ringing -- Got SIP response 486 "Busy Here" back from

Hi everyone! I couldn't find anything expressive about gtalk dialstrings. It doesn't seem to work. I'm not sure why, so I'll start at the easiest point. The syntax I found was: gtalk/my_account_name/buddys_account_name at gmail.com Is this correct? And does any of you googletalkers know, if a simple google-mail account is enough to use the talking bit, or do I have to

Hello, I've got a bunch outgoing-only SIP trunks "connected" to an asterisk 11 setup. I've read the following doc [1] stating you can pass username/password in a dial string. My goal is to dial from asterisk through one SIP trunk or another without touching my sip.conf file. In other words, I'm planning to use: Dial(technology/user:password at

Hi All I have a problem with mixmonitor in 13.4.0 doing the following: 1. Caller phones in 2. Reception picks up 3. Talks to caller 4. Does attended transfer, talks to manager to screen the caller wanting to speak to him 5. Complete the transfer by putting down her handset so the caller can speak to the manager 6. Caller talks to the manager The problem is that mixmonitor only records

Regarding this I've read the specs linked to in detail, but I can find no mention anywhere of any change that implies or states that no ring time will be recorded anymore in Asterisk 13 and that all times in start and answer columns will now be equal for all calls. Can this be because I nowhere use the Answer() application in my dialplan when dialing out? -----Original Message----- From:

I am having a problem setting the caller ID that shows when I make an outbound call over my PRI line. If I make a call from a SIP phone registered with the Asterisk box the PRI is connected to the correct ID shows on my cell phone. If I make a call from an IAX trunk connected asterisk box calling the same number as call one and setting the caller ID to the same number as call one the caller ID

I would love to get some feedback and test a patch to rev. 4380. First, the money shot - check out this demo of a scriptaculous DataGrid: http://development.finetooth.com/?p=13 I''m using the <tr> as a sortable with the <th>''s as the sortable elements. The Patch file: http://www.commoner.com/~lsimon/scriptaculous/delay_and_ignorePosition_forSortables.diff The patch

In a sortable list, is there a way to say, pass a className whereby some of the elements in the sortable element would not become draggables/droppables? If not, it seems like it could be implemented similarly to the handle option.. Any interest? Also - I submitted a patch that adds the option "delay" so that draggables in a Sortable won''t truly become activated until after the

Hi, I'm am currently in the process of trying to integrate an * box with an NEC Electra Elite IPK. Currently, we have 7 POTS lines coming into our building. These lines are plugged into our NEC using the appropriate analog line interface card from NEC. The NEC effectively has NO configuration done to it, other than to make all the internal phones ring when a call comes in. We also

On 5/23/2015 11:22 PM, Luigi Rosa wrote: > Kirk Bocek wrote on 24/05/2015 04:37: >> So I've built my first CentOS 7 host and am learning all the new ways >> of doing >> things. I setup and enabled ntpd but after a reboot I get: > > In CentOS 7 is bettere to use chrony, here's an howto > > http://linoxide.com/linux-command/chrony-time-sync/ > So

Hi people, question one i see that asterisk is now in 1.x release. having tried it in the past i want to know if i can use a voice modem as an outgoing line. i know in the past that was not possible/supported so im just asking in case the option is now available. question two im planing to use asterisk as a pure voip solution with sip phones and h323 phones no need for digium/dialogic hardware

Hey yall, I wanted to share some code I''ve been working on as it seems up the alley of folks on this list. It''s not rails, per se, but one day... DataGrid: http://development.finetooth.com/?p=6 This also showcases the option.delay perameter I''ve submitted into scriptaculous - hold down your mouse for one second on any column other than Vendor and then drag away ;) The

I recently posted a message about an interesting dilemma which I could not figure out. After doing a whole lot more digging I think I have figured out part of what is going on. The parking app is implemented as an app, ie can be called from extensions.conf) but if you look really closely, it is also implemented in each channels driver (handler, whatever you want to call it) and those

I''m wondering if anyone''s come up with a way to somehow make a Sortable look at X or Y position relative to the droppables so that the mouse doesn''t have to be over the container for the droppable to fire. For instance, take functional Sortable test #1. Grab Item #3 and then slide the mouse over to the left, past the dot (essentially outside of the <ul>). Now

http://www.commoner.com/~lsimon/scriptaculous/test/functional/dragdrop7_test.html In IE, if you click on the "Reload cart droppable via ajax", and then try to move the draggable, it goes kablaam. Notice too that if you reload and try to click Remove Droppable that the # of droppables stays at 1 or whatever, instead of going back to 0. The DOM comparison in Droppables.remove

So I've built my first CentOS 7 host and am learning all the new ways of doing things. I setup and enabled ntpd but after a reboot I get: $ systemctl status ntpd ntpd.service - Network Time Service Loaded: loaded (/usr/lib/systemd/system/ntpd.service; enabled) Active: inactive (dead) After issuing: $ systemctl start ntpd Ntpd runs just fine. But why isn't it loading at boot

Is there a way to ring selective line on multi-line phone. For example if I'm on the phone talking internally on line 1 and the calls comes-in the line 2 will automatically ring. The phone P104 allow extension to be assign each line. Is there a way to call certain line (example line 3) on multi-line phone instead of line 1 when the phone is not busy? For example the Sip phone P104 has

Hi, now I've got caller id working on my BT line in the UK, I'd like to play a different message to those pesky sort who with hold their outgoing number. How can I do this in my extensions.conf for my [incoming-analog] context? I realise some people may call who are unable to change the way that their system withholds the outbound number, so I'll give them chance to leave a voice

Sorry if this is the wrong list... I need a toll-free number to be delivered to me on IAX. (This is NOT an existing number need to buy the whole service.) Anyone know of a service provider offering this? -Mark 707-735-1038