similar to: need some advice

OK, I have a Asterisk @ Home 1.0.7 server with two Digium TDM400 cards, one 4 port FXO and one 4 port FXS. When I plug an analog cordless phone into the TDM40B card and setup a ZAP extension, the phone rings in and you can answer just fine. The weird part is when you try to get dialtone from the cordless handset it rings all of the other extensions... One other thing to mention is that the

Ouch, part reset, quickly restoring reality (0) Power alarm on module 1, resetting! I have looked though a lot of email on this issue, and no one seems to have the answer. How many people are seeing this on a TDM400 card? Does anyone have a "REAL" answer to it. Yes, I do have the power connected to it! Regards Garry Taylor

Hello! Attached to the bottom of this e-mail is an edited version of an e-mail I originally wrote to Digium tech support regarding Ouch and Power alarm errors I have been receiving on my TDM400. It contains a great deal of detail regarding my setup. In the end, I have found that one of the 5 phones I'm trying to make work with Asterisk is contributing to the generation of these errors.

Hi, I'm running * 1.2.7.1 on Red Hay 9.0 w/ a TDM 400 2 x FXS, 1 x FXO. I'm using a VTech cordless that makes three short beeps when someone another extension is picked up, presumably this lets you know if someone is trying to listen in.. Everything works, except the VTech now makes the three beeps everytime you try to use it, even if another extension is in use. It seems as though the

> Is anybody on this list actually using iax2 for > anything mission-critical? Yes. 2K inbound / outbound calls a day to 30 remote locations, aggregated to 2 PRI's tied together with IAX2. All with IP address specified rather than hostname. All with Asterisk 1.0.9. All with 99.9% completion rate, and it would be 99.999% if we weren't using consumer grade DOCSIS cable modems in the

Folks, I have a TDM400 with an FXS module. I'm having some trouble ringing some phones attached to the device. I have a real el cheapo handset that cost me about 9UKP. It works fine, I plug it into the Wildcard and call the channel and it rings. I have tried plugging in my BT Diverse 3016 cordless phone but it will not ring, although I can call out from it. I have also tried my GPO 332L

Hello. I am going to be putting together my first * system using FXO/FXS interfaces. All the systems I have set up thus far have been pure VoIP setups. The system I need to set up should have 3 FXO interfaces and 1 FXS interface, as well as several SIP phones. I have noticed people complaining about Digium's TDM cards - are these isolated incidents or are these cards unreliable? I intend to

Has anyone had success with the TDM400 in production? I have multiple boxes where these cards lock up and the only thing that will fix them is to unload *, modprobe -r wctdm, modprobe wctdm, load asterisk. Does not matter if it is a FXS/FXO module. I know this topic has been discussed many times before, but my questions is not "is anyone else having this problem" since I know that

iH have a TDM400 w/ 1 FXS & 1FXO card. after about a day or so the FXO stops working. after a reboot i get the following error. to get the card working again i have to shutdown, physically unplug/replug the card (reboot only, power off/on does not work) any ideas what may be going wrong here? thanks - hcir Zaptel Configuration ====================== Channel map: Channel 01: FXO

I'm looking for a zaptel type device with one (or more) FXO and one (or more) FXS port. Basically this guy would sit in-line of your phone line (PCI card). Any suggestions? TDM400 would be overkill. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050515/d66e6335/attachment.htm

Hi All - I pulled from a working system a TDM400 with one s110 fxs and three x100 fxos. I put it into a new box and the fxs no longer works. The fxos work just fine. I thought it was odd, but I chalked it up to a random chance failure and ordered another s110. The replacement doesn't work either, and now I'm confused. dahdi_scan recognizes the s110, but it says it fails. Output

I recently swapped 2 FXO modules on to what had previously been a 4 FXS version of the TDM400 board. The FXS ports are recognized - the FXO ports don't appear to be recognized (ie modprobe wcfxo and ztcfg both say channel 1 isn't there). Has anyone experienced this problem? All software is current as of this AM. If the old FXS modules are re-installed all works just dandy (other than

I've got this low-ping 100%-up dsl connection between two asterisk 1.2.7.1 servers. And oftentimes one of them would declare its opposite UNREACHABLE. Why can this happen? The host stanzas in iax.conf have raw IP's, so no DNS monkey business here.. An inquiring mind wants to know.

Hi I am setting up a phone system for a small office. The office will have 5-8 phones and a fax line. There are 4 hunt lines coming into the office. We have made no hardware purchase yet. Being an asterisk newbie, before I suscribed to this list I just assumed that I would buy voip phones and connect all the phones to a private ethernet network. However, I see many people inquiring about FXS

I have a TDM400 with an FXS and FXO interface. I have adjusted the TX and RX gain for both the FXS and FXO channels so that everything is balanced. I hear myself very loudly with no lag. I also get alot of background noise when the bridge is formed between the FXS and FXO channels. I have read the following articles: http://www.voip-info.org/wiki/view/Asterisk+echo+cancellation

I easily get confused when try to undertstand FXO & FXS ports. Is it possible to use an ATA to connect to a TDM400 card. If so, would I use FXO modules or FXS modules ? My goal is to connect my asterisk server to Vonage (via the ATA they send me) so I can use thier standard plan and do with out the Softphone account feature that only allows a few hundred minutes talk time. Thank you, Steve

I have a system that has a TDM400 with 3 FXO modules. Recently, the system started not seeing the ports. No answer, no lines available for oubound dial, and only a reboot of the machine will bring it back. Any ideas to try? Thanks, Tim --

Perhaps someone with more experience can help me solve this puzzle: Asterisk 1.4.18 on a Dell PowerEdge SC440, CentOS 5, 2.6.18-53.1.14.el5, Digium TDM400 with 3FXO(1-3) and 1FXS(4) Phone service is provided by XO Communications via their XOptionsFlex service (5 analog lines, 3 of which are used by Asterisk). For simplicity I refer to them as xx43, xx44, and xx45 - based on their phone numbers.

Hi. I have been searching through old threads and various forums, but can't seem to find out what the consensus view is here on the best type of FXO hardware to use for a home asterisk implementation. Specifically, should I buy a FXO ATA like the Sipura 3000, or a PCI form factor port like the Digium TDM400 series. I have read horrible things about problems with the X100P, so I have ruled

Hi, I'd like to build a personal PBX connecting 4 or 5 analogic phones with a ADSL line and I'd like to know what is the right card I need I visited digium site and I think TDM400 could be the right choice but I cannot understand how it works...I think it has 4 slots where 4 modules (FXS or FXO) can be inserted. How many cards do I need to connect my ADSL line to 5 phones? I think I