similar to: Generic X100P setup issues

Hello everyone. I hope that this isn't a sore topic, but I've spent a week now reading through everything I could dig up from the archives on this topic, and I'm not yet satisfied with any conclusions presented there. I've also spent a few days hacking on the Asterisk code, trying to understand how things work better, and I'm still not ready to give up. I well-realize

I can either get the TE100P working or the 3 X100P clones working, but never both. I have the TE100P connected to a channel bank, and X100P clones to lines from the phone company. This is my zaptel.conf span=1,1,0,d4,ami fxsks=1-24 loadzone=us fxols=25-27 loadzone=us I then do [root@asterix root]# modprobe zaptel [root@asterix root]# modprobe wcte11xp ZT_CHANCONFIG failed on channel

X101P with Ambient md3200 chip on it, with the zaptel wcfxo driver.... Just an indication of how many people have got this to work would be useful. Cheers Mark.

Hello, I have asterisk running on Fedora Core 3 with a x100p (oem). After some time I got asterisk with some soft extensions working (u gotta love open source), but I'm stuck with outbound dialing. This is the diagnose: - detect 1 wcfxo channel. - when trying to make an outside call I get unable to create channel of type Zap. Everyone is busy/congested at this time - When I plug the x100p

Hi, I'm trying to figure out why my Sweex CA000022 is not detected by wcfxo on my SuSE Pro 9.3 running on a VIA EPIA SP motherboard. The card should work as its an Intel 82537EP based card. When Booting the IRQ assignments for the board indicate: Bus Dev Func Vendor Dev Class 0 20 0 8086 1080 0703 lspci shows: 0000:00:14.0 Modem: Intel Corporation: Unknown device 1080

Hi, I've seen some reports about ruuning Intel modem with 537 or MD3200 chipset running with Zaptel drivers as a FXO port. Did anybody managed to set up a PCI faxmodem based on Intel536ep chipset to work with * and Zaptel drivers? Modem seemd to work just fine with Linux, but the driver says no;) some more info: Linux 2.4.26 mazuchna:~# cat /proc/pci | grep 536 Communication

Hi All, I hope I'm posting this to the appriopriate list, and that cross posting to two lists is OK. (If not, I'm sure I'll hear about it quickly :)) I'm running Asterisk on my (new) VIA EPIA-V motherboard. This seems to be the ideal platform for a home version of asterisk - its small, quiet, low power, and should have plenty of computing horsepower if only it would work!

Hi, I using asterisk 1.2.4 on a CentOS with Linux 2.6.9-22.0.2.ELsmp kernel. I've two x100p cards connected, only one card is reconigzed by asterisk. 02:01.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface 02:02.0 Ethernet controller: Davicom Semiconductor, Inc. 21x4x DEC-Tulip compatible 10/100 Ethernet (rev 31) 02:03.0 Communication controller: Tiger Jet

Hi All I've bought a TDM400P and need some help with configuration. Can you tell me what to do ? I've tried to install and the message below has appeared: [root@voip asterisk]# modprobe zaptel [root@voip asterisk]# modprobe wcfxo /lib/modules/2.4.22-1.2115.nptl/misc/wcfxo.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid

So I took a chance with an X100P knock-off on eBay. I'm running Asterisk + FreePBX on a PowerMac G3 (beige desktop) using Slackintosh 10.2 and kernel 2.6.16.16. Everything has been fine up until now. I compile the 1.2.5 Zaptel drivers without a problem, get the udev configuration in, modprobe zaptel, and finally modprobe wcfxo. At this point, I get the message: ZT_CHANCONFIG failed on channel

Hi all! I'm new with telephony cards and DAHDI drivers. I have installed Asterisk NOW 3.0.0 and update to Asterisk 11.7.0, modules are update too. I'm following the installation guide of Atcom [1] for AX1600P analogic card, modules are loaded [root at pbx ~]# lsmod | grep -E "hisax|netjet|dahdi" netjet 14618 0 isdnhdlc 4523 1 netjet mISDNipac

I have a TDM400 card with 3x FXO and 1x FXS ports on it. At the moment I'd prefer (till I can get it working more reliable with iaxmodem), for a faxmodem to answer one of the lines instead of the linecard. I've tried changing the context of that line so that the exten => s does nothing, but that stops the line from being able to receive calls (get a recorded This number is not

It seems that the Apollo MD3200 winmodem sold my newegg no longer uses the MD3200 chipset. At least the $13 version I ordered arrived with a different chipset. I made them aware of the issue and hopefully they will be changing their description soon. Anyway, I'm looking for a new source now, anyone know where to get these cards cheap? I know there is ebay, but I'm thus far getting sellers

We are looking at building a storage platform based on Dell HW + ZFS (likely Nexenta). Going Dell because they can provide solid HW support globally. Are any of you using the MD1200 JBOD with head units *without* an MD3200 in front? We are being told that the MD1200''s won''t "daisy chain" unless the MD3200 is involved. We would be looking to use some sort of

Does asterisk support the intel 537/md3200 chipset? I don't want to start any flames here, I know all about using generic crap in asterisk,[*] which I really don't approve of other than for testing, but I have a customer demanding a generic chipset for his one backup analog line. He will not spend the money for a Digium card and says he will find another company if I can not provide a

Do normal modems work with asterisk?

Now that the X100P is no longer being offered by Digium, what is the best solution? I seem to have run into a few posts where people talk about problems they've had with their X100P clone cards (dropping calls, echos, etc) other people seem to not have any problems. Of the three chipsets that will work: Intel 537EP, Ambient MD3200, and Motorola 62802 (as seen here

Owias, The 537 is, for the most part, a drop-in replacement for the Digium card. Please search the archive and the Wiki, as there have recently been several discussions about this exact subject. To my knowledge that is about the only modem that works, but keep in mind it is _not_ supported. That being said, follow the instructions on Digium's site for installing the X100P and you should be

PC: HP Vetra VL400 Mainbood: Intel815 BIOS: Phonix 4.0 release 6.0 OS: REDHAT 9.0 I installed the X100P in PCI slot 2 and disable the USB port, serial-port and parallel-port in BIOS. I can't found the X100P card in " cat interrupts" But I can found the card in the "cat ioports" use "lspci" I found the X100Pcard use the interrupts 11 too. Who can help me to solve

I'm new to asterisk and fror a cupple of days I heave been googleing the net for digium "clones", because it's very hard for me to get a digium card (X100P). Does anyone Know another substitute for X100P (I know that intel based modem with chip 537/MD3200 is working but I did not find any of those) ? I made it work with an Intel 536 (with a costumised driver that I found on