similar to: X100P Kernel Panic

How do I do this? Ive looked on lunix pages but ive seen that I have to change the config of the kernel build, is that right? Or do I need a different kernel altogether? Also the sites say the 8K is about as large as you should take the stack :oS Also someone posted that I need to sort out the IRQs, is this part of linux? As you can guess I'm kinda new to linux, although ive used it for 2yrs

Hey all, ? I'm trying to get an E400P and 2 X100Ps working together in the one box and don't seem to be having much luck. ? I can get the two different types of boards working separately, but not together.? I've made calls on both the X100P and have seen sync and correct signalling on the E400P.? But when I try to enable to configs together I get the following: ? modprobe wcfxo

Greetings all, I've just put two X100P cards to my box and despite trying everything I can find on the web, I can't get the second one to work. I've edited /etc/modules.conf so that ztcfg doesn't run automatically. To start, I run: /sbin/modprobe zaptel /sbin/modprobe wcfxo /sbin/ztcfg /sbin/modprobe ixj and ztcfg says: ZT_CHANCONFIG failed on channel 2: No such device or

Thanks for the reply Bill. I am aware of the interrupts problem. To solve it I have already disabled my serial ports freeing up interrupts 3 and 4 and these are allocated to the two cards. This was done 2 months ago and has not solved the problem. Is there any way that something can wake up every now and then and generate these two interrupts? My current /proc/interrupts is as follows:

List members, Is it possible to record outbound analog calls using an X100P? I was asked if I knew how to record all calls for a shop with 4 analog phones transparently to the end users. I thought Asterisk was a good fit for this and I envisioned using either Digium TDM400Ps or Sangoma A200s with 4 FXO and 4 FXS modules. The FXO modules would be connected to the existing PBX and the FXS

Hi, I recently purchased two X100Ps and a TMD40B. I have set everything up according to the instructions however I can't get asterisk to pick up an incoming call (It just keeps ringing). Also, when I pick up an internal extension I get dead air. I searched the mailing list for 3+ hours -- What am I missing? Thanks in advance for your help. Here are the installion steps that I used:

This must be a question asked before but can't find it so here I go: I have a Asterisk box connected, thou a x100p, to a PSTN PBX. When we get a incomming call on that PBX the phones in the office wil ring and there will also be a ring signal on the x100p. At my current configuration the call wil be answered by the Asterisk box. Is it possible to configure Asterisk to not answer the line

Hi can you help ? I have been trying to compile the zaptel modules all day for installation with out success, see messages below.... Setup as follows X100P card Intel Celeron (686) 1.7ghz processor Redhat Fedora Core 2 (Linux-2.6.5-1.358) When I do the make I get the following errors Any comments would be great ====> make make -C /usr/src/linux-2.6.5-1.358 SUBDIRS=/asterisk/zaptel-0.9.1

I can either get the TE100P working or the 3 X100P clones working, but never both. I have the TE100P connected to a channel bank, and X100P clones to lines from the phone company. This is my zaptel.conf span=1,1,0,d4,ami fxsks=1-24 loadzone=us fxols=25-27 loadzone=us I then do [root@asterix root]# modprobe zaptel [root@asterix root]# modprobe wcte11xp ZT_CHANCONFIG failed on channel

Hello folks, I'm very interested in the Digium/Asterisk combination but need some clarification. I would like to setup a SOHO for business and home use. Scenario One: I have one analog line, 4 analog telephones. Do I need a TDM400P + 4 FXS modules (Green) + X100P? Scenario Two: 2 analog lines, 1 selective ring number for fax, 8 analog phones. Is this what I need? 2 TDM400Ps and 8 FXS

I am interested in running asterisks and gno phone. However, i have yet to purchase the x100p cards. Is there a way for me to test asterisks in like a simulated mode or something? (to get used to it and the configs and stuff, prior to purchasing the x100ps?) Thanks all, A.J.

Hello I setup Asterisk@Home with purely VoIP and it worked fine. I then added an X100P card so I could call out / take inbound calls via PSTN and that went fine. But I have just added a TDM400P card (specifically a TDM30B) and now problems. Here is some of the output. Any ideas on what I should be looking at next? When I run genzaptelconf -s -d I get lots of erors on screen - bit I can

I am getting quite frustrated today, so please bear with me. I just installed Fedora Core 4 (was running RedHat 9 with a working Asterisk) now my Fedora does not appear to be recognizing my X100P (clone) at all. Hardware browser just shows them as unknown device. driver: hisax So, of course, my zaptel drivers do not work and therefore my asterisk does not work. any help would be greatly

Hello. Well I finally rx'd my dev kit (new batch of TDM's apparently. I'm on Mandrake 9.1 There were no hardware install instructions, it would have been nice to know whether the 4-way power connector was to be used or was for some other future or expansion purpose. It came with a floppy disc, no label and it wasn't even write protected. The only readme file was

Hello List, Im just dipping my feet into the asterisk world, and im having major fxo problems Im running Asterisk (from svn) + libpri (from svn) + asterisk-addons (from svn) + asterisk gui (svn 1.4 branch) + zaptel (svn 1.4) on a Debian Etch box, with 1gb ram, running all of the services for my home server (web / db / music server etc), and i would like to run my PSTN line from Kingston Comms,

PROBLEM: My x100p only does bad things. When I plug the line from the wall into the card, other phones in my house go nuts, no dialtone, crazy clicking, random tones, etc. Following the steps below, the line is screwed up any time I test after step 2. Just plugging the line from the wall into the x100p takes my other phones off line. External calls to my line hear busy. Obviously, can't

Hi Most of the threads in the list archive relating to X100P and hangups are about not detecting hangups. We have got the opposite problem. We have experienced an increased number of false hangups when connecting an X100P to an analog port of an ISDN terminal adapter. It happens more frequently on incoming calls than it does on outgoing calls. Often hangups occur after about 3-4 minutes into the

Hi, I'm still strugling with getting an easy to use conference system implemented. I did have app_conference running, but today I upgraded asterisk to 1.0.9 and it stopped working. I've tried following the instructions for compiling app_conference on 1.0.7 but it didn't work. So I went back to ztdummy (I've not had any luck getting this to compile on FC2). Anyhoo, I've

I have just purchased a 2nd hand X100P, if I do a ztcfg -vv I get: "Zaptel Version: 1.4.0 Echo Canceller: MG2 Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels configured." My understanding of the above is that the zaptel driver has detected the card. What do I now need to do, in order to get an incoming call to work with

All, I'm having trouble getting the X100P working. Lsmod shows : zaptel 179808 0 I did a . # modprobe zaptel and here is my zaptel.conf (comments omitted) __SNIP__ fxsks=1 loadzone = us defaultzone=us __SNIP__ Here is zapata.conf __SNIP__ [trunkgroups] [channels] context=default switchtype=national signalling=fxo_ls rxwink=300 usecallerid=yes hidecallerid=no