similar to: zaptel red alarms with e&m wink

I'm getting random Red Alarms with my T100P. I am using cvs zaptel from July 13, & have tried using remove clock source & local clock source. There doesn't seem to be any warning: every couple of days the line goes down, & then around 5 seconds later, it comes back up. If anyone as seen this behavior, or has any ideas about where to look, please let me know. Thanks, Glen

Hi, Did anyone manage to connect either Digium or Sangoma T1 card to any other PBX/gateway using T1 E&M Wink/Wink signaling? I'm trying to connect Avaya Definity to an Asterisk box with T100P and so far no luck. (I know I can do so with ISDN PRI, but need an additional ISDN processor card for Definity.) I tried to connect Definity to Cisco 3640 CCME (call manager express) to test the link

I am setting up a box with a T100P. Everything is going well. The company I am working with has their one phone switch gear. They provisioned me a E&M Wink T1. Cannot do PRI unfortunately. We chose E&M so we could pass an unlimited number of DIDs to the trunk as apposed to FXS loopstart signaling. I can make outbound calls no problem, but I am having problems with the dial plan for inbound

I could only get *ANI*DNIS* working one way and that was setting my signalling type on the Asterisk side to 'featd' The Definity won't send *ANI*DNIS* information back to the asterisk as far as I can tell. Other than that, I've been running it with wink/wink E&M for a while now. TN464 circuit pack on the definity side, te110p on the asterisk side. Just a crossover cable

Has anyone noticed a delay in sending DTMF to zaptel devices? I have a T100P connecting to an NACT telecom switch. All calls are sent just fine, but there are 4 seconds of delay between when the channel goes off-hook & the digits are collected by the NACT switch. I also have some cisco 5300 boxes connected, but there is no delay. Any ideas? -g

I have a couple of live T1s sitting around and they are not ISDN(like most of the people that are using Asterisk seem to be using), they are regular old 24 channel, robbed-bit, E&M wink start, D4AMI T1 circuits. Can I get these T1s to work with a T100P Digium card and asterisk? Searching through the lists and the documentation I haven't seen any examples of how to configure this kind

Attempting to talk to an Eagle Telephonics switch at a disaster exercise. Didn't think a plain old E&M wink start T1 would be this much of an issue. We finally got the Eagle to accept a call from *, but whilst I can hear the person on the Eagle, they can't hear me. When they initiate a dial out I only get the first 2 digits from their switch... Does anyone have decent

Asterisk is getting red alarms on my T1, sometimes once or twice a day, but today it happened 5 times. Even once is too many. Every call in progress is dropped. Please help! What do I need to do? What can I try? I've googled and searched this list and can't find anything. Here's an example from the logs: Feb 7 13:37:54 WARNING[32451] chan_zap.c: Detected alarm on channel 6: Red

We're having some difficulty connecting a T1 fax board card to asterisk, with E&M Wink. We've successfully connected it to other E&M Wink T1s, but have been unable to get asterisk to hear it's dialing. Asterisk can dial down to it with no problem, and it hears all the digits, but whenever it sends digits down to asterisk, * always only "gets" the first one. This is

Hello, About every 2 or 3 days I notice in the messages log file: Dec 17 08:39:27 WARNING[1220]: Detected alarm on channel 2: Red Alarm Dec 17 08:39:27 WARNING[1220]: Detected alarm on channel 3: Red Alarm Dec 17 08:39:27 WARNING[1220]: Detected alarm on channel 4: Red Alarm Dec 17 08:39:27 WARNING[1220]: Detected alarm on channel 5: Red Alarm Dec 17 08:39:27 WARNING[1220]: Detected alarm on

I am preparing to connect an asterisk box with a redfone fonebridge to a T1 service provider. I am doing this by testing first with another asterisk and a Sangoma card playing the role of telco. I formerly had this test configuration operating flawlessly as a PRI connection. But I discovered that I will need to use E&M, thus I've chosen the parameters as described in the subject

Hi List, I have some T1 750s; hookup via a T1 to a TE420P card. We have them all set as E&M wink trunks. We get a dial tone and can call numbers, but when i call another number the ringing I hear on my phone is very weird, its not the standard ring tone. What will cause this? Is this a * setting or something in the Adtran I am fixing, I just want good ole ringing to be heard! Any help would

List: I already have asterisks up and running on a PRI, but where we are moving we cannot get a PRI so we are going to get T1. My question is: We are going to us E&M Wink for signaling with DTMF and caller id. The channels are going to be setup like this, 12 channels for 2-way and 12 channels for incoming only with DIDs. How would I configure the zaptel.conf? I realize that I will have two

Are there any debugging tools for the digium zaptel cards that would report the activity on the line, such as DTMF and/or connection protocol? I'm looking to debug the connection with a T100P, & I don't have $2000 for a T1 test set. Thanks, Glen

Hey folks, I'm pulling my hair out on this situation and would welcome some advice: I'm using the AMI Manager to Originate calls onto 2 E&M wink T1 circuits via a T4XXP card from Digium. Everything works fine for about 600(+/- 50) calls then the Manager is suddenly unable to launch calls. Using ZapBarge to listen to the channels themselves you can hear the dtmf digits being dialed,

I am trying to make an in/out trunk group comprised of 4 DS0's using E&M Wink signalling. The first four channels of a DS1 on a T100P are being used for the group. Outbound calls work fine, but inbound calls fail. The other 20 DS0 channels are used for a PRI. Does the configuration shown below look okay? I've tried setting 'immediate => yes' without success, but it

I'm trying to get a patch tested for inclusion in CVS. Anyone that is running E&M on a T1 and had to fool around with emdigitwait could you please try this. This patch removes the need for the emdigitwait parameter and speeds up dialing. This situation is mostly interfacing a legacy PBX/Key system with Asterisk. I've been running a couple of systems with this patch for

Hello, I've got very annoying behaviour from our asterisk PBX. We have 12 channels T1 e&m wink start for TDM and using iax softphones internally (iaxcomm, but tried firefly-thirdparty and discarded for bad sound quality). Slackware 9.1 w/ kernel 2.4.26+ digium TE110P card. In some cases when call is placed from softphone to TDM, system does not detect call answered on Zap channel and

I am an Asterisk newby, and I cannot seem to get Caller ID information from our T1 line. When calls appear at the phones, they say the call came from "asterisk" and unknown number. I know how Caller ID information is passed on an analog phone line (between the rings) but with a T1 line, I don't know technically how it is done. I don't see the caller's number in the

Check with your telco. We had the same problem on 1 of our PRI's, every day at 5:00 sharp, red alarm, with all calls cut off for 30 seconds exactly. Turns out the equipment at the CO was going into a test loop at that time because of a forgotten setting by a tech. Man, what a finger pointing exercise that was. -----Original Message----- From: Matthew Boehm [mailto:mboehm@cytelcom.com] Sent: