similar to: 2 E100P cards on one asterisk

Hi, I'm installing E100P for isdn pri line. My configuration are like this. zaptel.conf ======================================= span=1,0,0,ccs,hdb3,crc4 loadzone = us defaultzone=us bchan=1-15 dchan=16 bchan=17-31 zapata.conf ================================================= [channels] context=default switchtype=euroisdn context=default signalling=pri_net usecallerid=yes

Hi, I am running * with E100P board. At least every our I got an Error 500 message and ISDN-PRI restarts: Jan 10 12:53:02 WARNING[98311]: File chan_zap.c, Line 5758 (zt_pri_error): PRI: Read on 27 failed: Unknown error 500 Jan 10 12:54:27 WARNING[98311]: File chan_zap.c, Line 5758 (zt_pri_error): PRI: Read on 27 failed: Unknown error 500 Jan 10 13:33:01 WARNING[98311]: File chan_zap.c, Line

hi guys, I have a little problem maybe you can help ... I have an asterisk setup, with an E100P, and an ISDN-PRI 30 channel line from the telco going into it .. the E1 line is OK, because plugged into a Lucent Portmaster 4 it works OK .. plugged into the asterisk box I just get an engaged tone, and asterisk posts this message on screen : WARNING[1167272000]: File chan_zap.c, Line 5275

Hi ! I am trying to configure two E100P cards, but I am a bit confused with zapta.conf in what I am trying to achieve. The * will be connected to a pstn switch with two E1 PRI lines. The E1 lines will be used for incoming calls as well as outgoing calls. My problem now is what to put in zapta.conf, I would like to group all channels from both cards together (if that's possible). Does this

Hi.... Apologies for the length of this, but any help would be greatly appreciated ;-)... I have installed and configured a Digium E100P on my Asterisk PBX and I have connected this to an 8 port E1 VoIP gateway on a Cisco 6509. There is also an external E1 link from our Telco plugged into one of the other ports on this gateway and this gateway is in turn registered with a Cisco CallManager

Dear All, I'm having a problem with my Asterisk + E100P Installation in UK (BT PRI). The system functions as expected, and my dial plan works as expected. 30 minutes (or so) after starting the asterisk service I lose the PRI line, and only get this back after a service asterisk restart or reboot. During the failure there is no alarm on zttool, ztcfg show all 31 lines and there are no

Just cross pairs 1-2 and 4-5 1 <--> 4 2 <--> 5 Never done an E1, but I think it's the same for a T1 4 wire cable. Tim Thompson Commercial Sales Engineer http://www.amatechtel.com (806) 722-2227 -----Original Message----- From: bam [mailto:bam@cqm.co.uk] Sent: Monday, December 29, 2003 9:12 AM To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] E100P pinouts

Hello, Thanks to members of the list things changed on my installation (asterisk + digium E100P with of course an E1 line). Here is my zaptel.conf : - span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=fr defaultzone=fr - Output of zttool: - Alarms Span YEL/RED Digium Wildcard E100P E1/PRA Card 0 - [root@asterisk root]# head /proc/zaptel/1 Span 1: WCT1/0 "Digium

Hello ml, i need some help on my zaptel configuration. My E100P only shows some YELLOW / RED alarm when I load the wct1xxp module and do a cat /proc/zaptel/1 Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3/CCS YELLOW RED ... .. . My /etc/zaptel.conf is: span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=nl defaultzone=nl I tried zaptel-1.0RC2 and the latest CVS

Hi all, I am trying to setup an E100P for use on Swisscom E1-PRI here in Switzerland. Swisscom seems to use Siemens hardware. Here are my configs (cvs from a few hours ago) : zaptel.conf loadzone=fr ; tried "de" but got warning at modprobe defaultzone=fr span=1,1,0,cas,hdb3,crc4,yellow ; Seems to be right, as the Siemens SDSL-G703 modem switches its LEDs off ... not sure

Hi, all I am trying to install E100P card, the 'modprobe zaptel' is ok, but when I did 'modprobe wct1xxp', I got such error, so can not load the driver for the card. /lib/modules/2.4.20-8/misc/wct1xxp.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog

Hi. I still hace problems getting my line to work. When I start asterisk, I can see: == Parsing '/etc/asterisk/zapata.conf': Found -- Registered channel 1, PRI Signalling signalling ... -- Registered channel 31, PRI Signalling signalling == Starting D-Channel on span 1 == Registered channel type 'Zap' (Zapata Telephony

Hello I have installed my new E100P card in the same machin with two TDM04B cards. I have followthe instructions on http://www.digium.com/index.php?menu=configuration#T_E100P_PRI This is my zapata.conf span=1,0,0,cas,ami fxsls=1-15,17-31 dchan=16 fxsks=32-39 loadzone = us defaultzone=us I do *modprobe zaptel wct1xxp wcfxs ans seems to work ok. * But when i do ztcfg -vvv i got Zaptel

Hi, I've got an important question: I use an E100P directly connected to PSTN, but it does not *really* work as it should be: exten => 1000,1,Dial(Zap/1/1234) BUT: It does NOT dial "1234" but it says in debug mode: -- Called 1/72976451 Apr 26 00:53:00 WARNING[10251]: chan_zap.c:5979 zt_pri_error: PRI: !! Facility message shorter than 14 bytes -- Channel 1, span 1 got

Greetings. Today I've installed a fresh new E100P on a EuroISDN PRI. It seems to work well, accepting calls, but, when I start *, I have the screen flooded with this message: PRI got event: 8 (or 6) If i look into /var/log/asterisk/messages i've this Error: File chan_zap.c, Line 5341 (zt_pri_error): PRI: Read on 35 failed: Unknown error 500 Repeated indefinitely. Also, i've a

Hi all: I have problems to setup my zaptel E100P hardware. When I start * after receive the "Asterisk Ready" I see this: *CLI> Jun 22 20:37:55 NOTICE[1133718080]: chan_zap.c:4881 handle_init_event: Alarm cleared on channel 1 Jun 22 20:37:55 NOTICE[1133718080]: chan_zap.c:4881 handle_init_event: Alarm cleared on channel 2 Up to channel 31. anfter this: Jun 22 20:37:55

<P>hi Everyone,</P> <P>We are configuring an ISDN PRI E1 with an E100P card, when you load the drivers, and starts the asterisk, cards also starts fine, givin following output,</P> <P>*CLI> <BR>&nbsp; == D-Channel on span 1 up<BR>&nbsp;&nbsp;&nbsp; -- B-channel 1 successfully restarted on span 1<BR>&nbsp;&nbsp;&nbsp; --

Hi all, I replaced a TE410P Rev C 1st Generation Firmware with a TE411P without any cfg changes (zaptel/zapata). As a result Asterisk crashes on outbound from PRI4 going to PRI1 calls: Aug 23 18:22:00 WARNING[4693]: chan_zap.c:7545 zt_pri_error: PRI: !! Got a UA, but i'm in state 1 Aug 23 18:22:00 WARNING[4693]: chan_zap.c:7545 zt_pri_error: PRI: !! Got a UA, but i'm in state 1

Hi, I have two E100P boards connected to my PC. I wish to setup two E1-ISDN-PRI lines, the first SPAN with 15 channels and the second one with 30 channels. When I try to load zaptel modules, I get an error message: "Loading zaptel framework: Loading zaptel hardware modules: wct1xxp wcusb Running ztcfg: ZT_CHANCONFIG failed on channel 63: No such device" Follows my zaptel.conf: