similar to: Sipura-SPA2000 background noise

All, If you currently own a Sipura SPA2000, avoid going to the sipura website and upgrading the firmware. I upgraded my SPA2k a couple of days ago from 1.0.9 (what it came with) to 1.0.18 off the site, and I am having issues with my SPA rebooting itself every 3-10 minutes for no apparent reason. I have been in touch with the *excellent* sipura support folks, and they are working with me to

Hello We have setup a doorbell which has an inbuilt analog phone which is connected to our Asterisk via a SPA2000 ATA. The problem we are getting is that when a caller presses the buzzer it is taking two or more minutes to finally call the reception phone. In the SPA2000 I have set dtmfmode to be inband. I notice that with the asterisk you dial a number and then it waits for a timeout

Hi, I've one Sipura SPA2000 at home behind a linuxbox with two network adapters (eth0 for WAN and eth1 for LAN) doing NAT/DHCP: ___________ HOME _______________ ____OFFICE ____ SPA2000 <---> Linux Box <--> Asterisk Box 192.168.0.253 192.168.0.1 eth1 200.93.xxx.a 200.93.xxx.b eth0 My problem is when I try to call to any trunk or extention

Hi I have just got Asterisk going with an spa-2000. however when I look through the userpdf every function on the sipura and asterisk seems to require on-hook or flash button , all of the phones i have do net seem to have either, is there a way round this ? does anyone know. Or do i ahve to go out and buy more phones? Anyhelp appreciated Simon

Been having a problem with my two Sipura 2000's dropping calls from the SPA-2000 side. Seems the calls are dropped right before the "Next Registration" time. Calls drop about ever 60 minutes or so. I have dialed from one port to the other and let it sit. After about 60 minutes or so the calls get dropped. System details are below Asterisk ver. CVS-HEAD-11/27/04-23:42:45 RHEL 3

was breezing over http://voxilla.com/ Looks like a new ATA from the founder of Komodo Technology (aka the Cisco 186) Sipura SPA 2000 http://www.sipura.com/products/spa2000.htm to join the others Cisco ATA 186/188 http://www.cisco.com/warp/public/cc/pd/as/180/186/ 8x8 DTA-310 http://www.8x8.com/products/home_office/dta-310/index.asp.html Grandstream HandyTone 286

I have a Sipura SPA2000 2 line SIP FXS box with line 1 on port 5060 and line 2 on 5061. The SPA2000 is on IP address 192.168.17.6, and the asterisk box is on 102.168.17.2. Both SPA2000 ports(5060 and 5061) share the same IP address. Every minute I repeatedly get the following output: SIP Debugging Enabled 10 headers, 0 lines Reliably Transmitting: OPTIONS sip:192.168.17.6 SIP/2.0 Via:

Hi there, I have setup Asterisk with a couple of Sipura SPA-841's and Grandstream ATA's. The problem is that with both of these devices the Unattended call transfer process seems to be just like Attended but instead you hang up as soon as you have dialled the number of the party your are transferring to. The call transfer all works fine BUT as you complete your side of the transfer

In trying to get my services up and running, I've encountered the usual spate of first-time issues. I was wondering if there was a good FAQ or Howto on troubleshooting NAT issues. The equipment that I'm using is typically a Sipura ATA or hardphone (SPA-942) sitting behind either a Linux box as firewall (using IPtables and Arno's firewall) or else a Cisco IOS device running 12.4T

Hi All, I'm on of those brave souls who bought into the preproduction beta of the Sipura SPA-3000 FXS/FXO adapter. I've had the unit a few days and am exploring it's workings. I really want it mostly as a straightforward FXO adapter, to replace an X101p. Let me be clear, I'd love to support Digium in every way possibe, and will likely buy a TDM40 card shortly. But, the X101p has

I've just made an interesting observation that I'd like to share with you all: the popular Sipura SPA-2100 just doesn't seem to be as great as I'd hoped. I've been trying to get inbound AND outbound faxing working via Asterisk and at least one of my termination services: Voicepulse or Sixtel. In general, inbound has been working flawlessly but outbound has been pretty

Hi My head hurts... Can anyone help out here, my remote IAX can see my local IAX and visa versa, conversation starts, I can dial my remote (POTS) landline number, remote end answers, trys to route to local iax2, I see it start the conversation here, the extension (SIP) rings once and then it dies... Both ends are defined with accept IPADDRESS to keep it in the family and simple.. Debug info

Hi all, We have several sipura 3000's working well for outbound calls, however the issue we have is that when calls are sent to the Sipura with Dial(SIP/${EXTEN:0}@sipura1) the Sipura does a SIP answer immediately and then proceeds with the call "in band" therefore sending dialing sounds back to the caller. Other SIP gateways we have notably the Vegastream and others do not do a SIP

I've been having problems getting MusicOnHold to work, so I've dumbed down my setup to as simple of a setup as I can. Asterisk 1.0.9. SIP ATA's (Sipura SPA-2002's) <SIP ATA 1> <---> <Asterisk> <---> <SIP ATA 2> Both ATA's have public IP's. No NAT'ing going on here. Reinvites are allowed so the media stream bypases Asterisk once a call

Hello, I've been experimenting with Asterisk 1.0.6 and a Sipura SPA-3000, and I've run into a couple of questions I haven't yet found clear answers to: It appears that the SPA-3000 has no call progress on it's FXO interface? Asterisk considers a dial() as answered when the SPA-3000 has dialed the number on the PSTN line, not when someone has answered a phone on the

Hi, I'm using the SPA-2000 with firmware 1.06 on the Asterisk PBX, which works great for taking and placing calls, but for for some reason I can't seem to clear the stutter dialtone by either calling the extension I'm on, or the voicemail system on the Asterisk PBX. If I call my voicemail access extension directly, It tells me I have no messages waiting, yet when I hang up, then

Hi, I'm looking for a full list of xml provisioning variables of the SPA-2100/3000. Currently the Sipura website has example XMLs only for the SPA-841 [1] and SPA-941 [2]. I'm mostly interested in the CallerID type selector variables and whatever variables control the PSTN<->VoIP settings. Sipura Configuration website form field names are numeral only. :( [1]

I had a problem in the past with a SPA-3000 acting funny that Sipura helped me with by telling me how to factory reset it. They responded in less than a day to my email request and the unit has worked fine since. I've had similar turn around on requests related to a batch of SPA-841 phones. They were all handled by real people who appeared very knowledgeable on the products. This appears

All, I am looking at a little support on this, as I haven't found it on google yet. I have had this work on Callweaver, but am moving to Asterisk for a variety of reasons. My dial plans, and everything else transferred perfectly, though I am not sure they are 'correct' for Asterisk 1.6.1, with simple things like SIP users outlined in the sip.conf file, not in the users file,

If I understand correctly the Sipura people are the same guys that made the Cisco ATA (Komodo phone) or what ever. I'm going to get one of the Sipura SPA-2000 to use and abuse with *.... I have seen the web interface.. John over at Chagres was nice enough to let me login to one and look around a few weeks back... I'm impressed .. if you guys care to buy one