similar to: Crc4 issues

We are located in Belgium and just ordered a PRA line, the telco asked the following questions : - 120 or 75 ohm ? - Support for CRC4 yes/no ? - B channels in 2 way ? We will buy a digium card but which one should we buy ? could anybody help me with this ? Thank you Michael Sorry for the previous html mail DISCLAIMER: The content of this e-mail message does not constitute a commitment

Hi all, Can somebody help me out, to get the call going through to my provider? I connected my A104D Sangoma card to E1/isdn and each I tried to make call I get the errors below. My protocol analyzer can see only setup info and release complete. WIRELESS2*CLI> set debug 9 Core debug was 0 and is now 9 WIRELESS2*CLI> pri intense debug span 1 Enabled EXTENSIVE debugging on span 1 T203

Dear Telcotype Braniacs, I have tried doing a google search to find out what this switch looks like, what the physical interface is, but havn't been successful. I am quite new to the ISDN world so I'm not sure what to expect when I see this switch. Does anyone have any experience connecting to this switch? The following is basically all I have been given for info: 1) Ericsson, AXT121,

I have a system setup with two T1 circuits, the customer complains of call quality issues. I've checked logs and don't see anything too strange, but when I run "dahdi show status" I see: Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO T2XXP (PCI) Card 0 Span 1 OK 0 0 19 ESF B8ZS YEL 0 db

Hi, We have a Ericsson BP250 Phone system setup witht he following configuration Telco <-> Asterisk E405P <-> BP250 The system seem to work perfectly on 1.0.9 for a very long time but there is some functionality we wanted to take advantage of in the 1.2 version branch so we upgraded. Currently running Asterisk 1.2.4 Zaptel 1.2.3 (noticed 1.2.4 is out will upgrade next

We connected an * box with an e100p to an E1/PRI from a telco here in Italy. After we had it working perfectly the telco told us that, despite the circuit appeared to work fine, and we could place calls on it, they had an "E-bit2 alarm indication constantly on that caused the circuit to be flagged as "faulty" every time. (The E-bit indication, is an alarm sent back from us to

------ Original Message ------ From: "Tony Kasule" <timotsmith at gmail.com> To: "Asterisk Users Mailing List - Non-Commercial Discussion" <asterisk-users at lists.digium.com> Sent: 30/06/2015 8:34:47 p.m. Subject: Re: [asterisk-users] Help With Physical Layer >Hello, > >Anyone to help me with this issue? It has never worked :( Hi Tony I'm not

Hi, I am new with asterisk. I am setting a Wildcard TE405P. E1s in Italy come in on a pair of RG-59 coax cables with BNC connectors. So I need an adapter/balun http://www.allcomtlc.com/al_g703n3.htm . I have It but I am not sure that It works. I have configured my asterisk in this way: zaptel.conf span=1,1,0,ccs,hdb3,crc4 dchan=16 bchan=1-15,17-31 loadzone=it defaultzone=it zapata.conf

Hola! I've a Digium E1 card, zaptel recognizes it as (loading the module with debug=1) Setting up DMA (write/read = 321b2000/321b2200) Controller version: 43 Framer: DS21554, Revision: 5 (E1) Found a Wildcard: Digium Wildcard E100P E1/PRA Using CCS/HDB3 coding/framing with CRC4 120 Ohms Calling startup (flags is 4099) Started DMA Got interrupt: 0x0005 /etc/zaptel.conf:

Hi whatever I set the span line to in zaptel.conf ie span=1,0,0,ccs,hdb3,crc4 span=1,1,0,ccs,hdb3,crc4 span=1,2,0,ccs,hdb3,crc4 zttool always shows Sync Source: Internally clocked surely this cannot be correct.

I have my peers registered to SER.asterisk seems to be sending mwi for the peers seen in the sip show peers CLI command. i have my ser server registered with asterisk as a type=friend and all clients register to ser.how do i get mwi to work for these clients registered to SER. Thank you, -AA

Hi, I have a digium card (igium, Inc. Wildcard TE405P quad-span T1/E1/J1 card 5.0V (rev 02)) 4 ports I want to make a loop test between digium card E1 to test the configuration of dahdi What I want to do scenario is I connect port 1 and port4 in the digium card with E1 cable SIPcall-->E1 Digium port 1--->(Loop)E1 port 2---->sip extension local. kindly can any can help me to

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello List, since some days i run into the problem that one span on a TE407P is not comming up correctly. With intense debug on that span i get: < [ 02 01 7f ] < Unnumbered frame: < SAPI: 00 C/R: 1 EA: 0 < TEI: 000 EA: 1 < M3: 3 P/F: 1 M2: 3 11: 3 [ SABME (set asynchronous balanced mode extended) ] < 0 bytes of data

I have 7965 and am trying to convert the firmware to SIP (SIP45.8-3-4SR1S). Does anyone have a valid XMLDefault.cnf.xml they could share? I have tried the version at voip-info<info.org/wiki/view/Asterisk+phone+cisco+79x1+xml+configuration+files+for+SIP&view_comment_id=14768#Troubleshooting>for the 7941/7961 but unfortunately /var/log/messages shows in.tftp stops sending after

Hello. I have a TE212 configured in E1 mode. This is shown in a cat /proc/zaptel/2 and 3 (where the card is configured): cat /proc/zaptel/2 Span 2: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" HDB3/CCS/CRC4 RED NOTOPEN 25 TE2/0/1/1 Clear 26 TE2/0/1/2 Clear 27 TE2/0/1/3 Clear 28 TE2/0/1/4 Clear 29 TE2/0/1/5 Clear 30 TE2/0/1/6 Clear

Dear, I always had one E1 card with one span, so I've never had any problem in set it up through /etc/dahdi/sustem.conf and /etc/asterisk/chan_dahdi.conf because I put span=1. But now I have a PBX with two E1 cards with 4 span (8 span in total). How do I have to define both card in system.conf and chan_dahdi.conf, and how do I have to refer each span to the corresponding card ??? Thanks a

Hi all, Our asterisk PBX, randomly restarts all the channels of the E1 connection. It sends this message "There is no D-Channel, using channel 16 anyway".Then the asteisk recive (or it thinks it recives) yellow alarms at all the B-channels, after that it restart all the channels. When restarting the B-channels it cut all the conversations that is handling at that moment. Does anyone

We have a te410p, with the following connections: span 1 connected to a 32 Channel EuroISDN span 2 connected to a card in a legacy pbx (Meridian) span 3 connected to a 10 Channel EuroISDN span 4 connected to a card in a legacy pbx (Meridian) We have no need for the meridian now, and decided to turn it off. I did not change the zaptel.conf settings, nor the zapata.conf settings. When the

Hi all, We have been fighting with telco for a entire week. Today they came here with a LITE3000 to analyze what is going on. When I configure zaptel with no external clock, E1 gets aligned/synchronized with bit rate in 2048000 bps, both me and telco. span=4,0,0,ccs,hdb3,crc4 But when I configure span4 to get clock source from telco they become unsynchronized. TElco bit rate stays in

I have a 'CONGESTION' Status with R2 protocol. While testing this scenario sip GW--?Asterisk ?Digium E1 R2 Protocol?Cisco E1 R2 protocol?sip Gw Find below my error and configuration ,where are the errors in my configuration ? ========================================================================= Connected to Asterisk SVN-branch-1.6.2-r235775 currently running on