similar to: Still Adtran and T100p

Hello, I have just received Adtran TSU 600 with 24 FXS ports. I have installed sucessfuly T100P card. Adtran is connected to t100p with crossover T1 cable. On T100P card I have a green light and on Adtran I do not get any errors or alarms. But I do not get dialtone on FXS ports. Adtran is configured: For Network Timing, fxs ports ore fxs_ls on Adtran. In zaptel.conf: span=1,1,0,esf,b8zs

Hello, Did anybody successfully tried upgrade Adtran TSU 600 to firmware which is working properly with T100P and asterisk ? B.

I have following setup Asterisk - T100P -> Adtran TSU600 P + FXOcard -> PSTN line When PSTN line is plugged directly in to analog X100P caller id is received by Asterisk but when I plug it into adtran I'm not getting caller id. Any ideas what kind of setup Adtran TSU600 requires to pass caller id to T100P ??? regards m.

I have a T100P card connected to an Adtran and then a T1. I have added the following configurations to Asterisk...but, when I dial 9 and then a local phone number, it bounces between the dial tone and silence and the *error* light on the Adtran blinks. zaptel.conf span=1,0,0,esf,b8zs fxsks=1-8 loadzone=us defaultzone=us zapata.conf [channels] context=from-sip signalling=fxs_ks

Hello, I new to this, but with the help of mailing lists archives and IRC I am able to build my PBX. Thanks to all who had help me to reach till here. I am stuck at a point where I can't find the solution on mailing lists or even on IRC. I have individual 4 DID (Direct Inward Line) coming from Telco and terminating into TA 750 to FXS card. Many of them told that Phone instrument terminates

Hello all, I've got a T100P connected to an Adtran TA750 with a T1 crossover... This connects to a patch panel with phone ports. The Adtran is fully populated with FXS cards. All I get on any phone port is a fast clicking noise... No dialtone. Asterisk 'sees' the card, (the channels show up in /proc/zaptel). Incoming calls are routed to the zap/x channel, but no ring. I'm

Hello, So all the pieces are finally here, and I'm ready to play. I remember reading on this list that the connection Channel Bank <-> T100P requires a "reverse cable." Is this a regular Ethernet reverse cable (i.e., only a couple of pairs reversed?) Please help me before I blow something up! Saludos, Jose.

It is possible to connect ADTRAN TSU 600 VP24 FXO 24 Port Channel Bank to Asterisk ? Somebody offered me that hardware, but I do not know if thats good hardware for Asterisk. rgs, Bartosz -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20030820/4a9e4608/attachment.htm

Jay, I have had a lot of trouble with the FXO ports on Adtran TA750. Unless the incoming POTS lines have a balance impedance, they will buzz very bad. Gregory P. Scasny Golden Technologies Inc. http://www.golden-tech.com 219-462-7200 -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Jay Milk Sent: Sunday, April

I've been working with an adtran ta 850 hooked to a t100p pretty much all day today, and I haven't gotten past configuring zaptel.conf and zapata.conf. For some reason, when I pick up analog phone hooked up to the first module of a quad fxs card in the second slot of the ta 850, asterisk thinks that all four of the fxs modules in that card are going off hook. If I pick up a phone hooked

Hello, I have a T100P card on a Red Hat 8 machine with Asterisk installed on it and I'm trying to get the data routing properly through it. I purchased an Integrated Data/Voice T1 Line with channels 1-6 voice and 13-24 data. The line is plugged directly into the Asterisk machine's T100P card. Previous to the asterisk set up we had an Adtran router that connected everything to what the

Can I configure an Adtran channel bank with a mixture of FXS and FXO cards and have them come into a single T100P T1 card? It seems like this would be a cheaper solution than trying to load a bunch of PCI cards into a PC. Also, when shopping for an Adtran (on ebay) - what do I need to watch out for as far as interfaces or capabilities to make sure that it works with a Digium card?

I am having some difficulty getting a T100P card to work with my PRI. When I attempt to make an outbound call via: exten => 1004,1,Dial(Zap/g1/NPANXXXXXX) I see the following on the asterisk console: -- Executing Dial("SIP/sbruton-b8ce", "Zap/g1/NPANXXXXXX") in new stack Apr 21 08:18:48 NOTICE[16401]: app_dial.c:554 dial_exec: Unable to create channel of type

(to mods: sorry for any extra work I've put you through. Posting from my work account, as proper) Hello all, I'm back. I've got that lucky feeling that this will all work out very soon, and I hope that that is true. The issue: In my * server I have a t100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm

Skipped content of type multipart/alternative-------------- next part -------------- No virus found in this outgoing message. Checked by AVG Anti-Virus. Version: 7.0.298 / Virus Database: 265.6.4 - Release Date: 12/22/2004

Hello, I have ISA card LineJack. I could not find any information if this card can work as fxo with Asterisk. If it can work, can somebody point me how to install it on my Asterisk box. Or maybe there is some documentation about it how to install LineJack. I will be very thankful for any help. Regards Bartosz Jozwiak ------------------------------------------------- This mail sent through IMP:

>>TURN OFF HTML!!!!!!!!!!! >>Why the hell do you feel I need to read your text in a lightish blue >>color???????? Do you know how shitty that looks compared to everyone >>elses black on white. Blue doesn't offer the contrast my eyes prefer. So >>why the hell do you feel important enough to override my defaults? You >>sir are the annoying guest who comes in

My carrier tells me our Adtran is seeing error seconds and timing slips. Is there any way to check this on the T100P, maybe in /proc? Craig Bruenderman Network Advocates, Inc. 300 Envoy Circle Suite 300 Louisville, KY 40299 Main: 502-412-1050 DID: 502-992-5929 Fax: 502-412-1058 Mobile: 502-548-1100

I have just received a T100P and an Adtran TSU 600 in the mail. I seem to be having a problem with the T100P card. So far I have done the following: vi zaptel.conf fxoks=1-22 fxsks=23-24 ... vi zapata.conf ... signalling=fxo_ks ... channel => 1-22 ... signalling=fxs_ks ... channel => 23-24 I then run modprobe zaptel modprobe wct1xxp ztcfg -vv There are no errors to report. In

Hello, We keep having a really bad static problem on phone calls completed using a Adtran TA750 and T100P card. The phones are Polycom IP 500 phones and, it occurs across all phones. Not just one. Everything appears to be on it's own interrupt. I noticed the last time we did this, we rewired everything to make sure it wasn't an electrical issue. Well about a month and a half later