similar to: ZAPTEL not loading on FC2

I've got a fresh FC2 install and I'm trying to get the symlinks right according to the /usr/src/zaptel/README.Linux26 instructions. I've created two symlinks: /usr/src/linux-2.6 -> /usr/src/linux-2.6.5-1.358 /lib/modules/linux-2.6 -> /lib/modules/2.6.7-1.494.2.2 When I do a "make linux26", I get a million warnings and errors with the result being: make[2]: ***

Followed the "instructions" on voip-info.org regardinging fedora FC2, making Zaptel seems to work fine, however when I modprobe I get this. It looks like a version mismatch somehow. Ideas? If this ooc, sorry first post here :-) modprobe tor2 WARNING: Error inserting zaptel (/lib/modules/2.6.5-1.358smp/misc/zaptel.ko): Invalid module format WARNING: Error inserting zaptel

When I try to start up zaptel, whilst running ztcfg, I get the following error: Jan 1 10:48:18 bu ztcfg: ZT_CHANCONFIG failed on channel 2: No such device or address (6) My /etc/zaptel.conf is: fxsks=1 fxoks=2 loadzone = au defaultzone=au Channel 1 is a X101P card connected to the PSTN and channel 2 is a S100U box driving an analogue phone. The zaptel kernel module gets loaded OK as does the

Thanks for replying. It's there, /usr/src/zaptel and it's valid. The script checks for its existence before compiling. The only thing that's unusual about this zaptel is that it is patched to support KB2 echo can. Gavin: Thanks, already cc'd Sangoma support. Hope they are working today! -----Original Message----- From: Eric "ManxPower" Wieling

Sangoma support did something and the driver is there. Rebooting now with the new card. Hold me, I'm scared. -----Original Message----- From: Colin Anderson [mailto:ColinA@landmarkmasterbuilder.com] Sent: Friday, December 22, 2006 10:09 AM To: 'Asterisk Users Mailing List - Non-Commercial Discussion' Subject: RE: [asterisk-users] Sangoma Wanpipe 2.3.4-3 compilation fails un der FC2

Dear Sirs, I'm running an Asterisk 0.9.1 in a Fedora Core 2 box. I installed a X100P card on my box and when i try to load modules i am rejected. When i type modprobe zaptel my Fedora respond : "FATAL: Module zaptel not found." . The same uccurs when i type "modprobe wcfxo" May you help me. Thank you in advance Juanjo

I wouldn't normally post this to the asterisk mailing list but I'm really stuck... I've been trying to get meetme working on and off for a few months now but I always hit a brick wall when trying to compile. I keep seeing this... make linux26 cc -I. -O4 -g -Wall -DBUILDING_TONEZONE -DSTANDALONE_ZAPATA -DZAPTEL_CONFIG=\"/etc/zaptel.conf\" -c -o gendigits.o

LD [M] /root/wanpipe/patches/kdrivers/wanec/wanec.o Building modules, stage 2. MODPOST *** Warning: "register_wanec_iface" [/root/wanpipe/patches/kdrivers/wanec/wanec.ko] undefined! *** Warning: "unregister_wanec_iface" [/root/wanpipe/patches/kdrivers/wanec/wanec.ko] undefined! CC /root/wanpipe/patches/kdrivers/wanec/wanec.mod.o LD [M]

I have just upgraded from Asterisk 0.7.2 to 1.0.2 and seem to be having an issue with the zaptel init script.. If I run.. #modprobe zaptel #modprobe wcfxo #modprobe wcfxs .. from a command line it load and appears to be working fine.. If I try and use the init script I get errors about ZT_CHANCONFIG and the modules don't see to laod up.. Anyone got any pointers? I am running Fedora Core

Hello, my first post to the list. I have started to install and play with Asterisk. I was following some basic instructions to 'jump-start' my system. I have a TDM400P with one port and a X100P. I am running the latest CVS versions (from today). Following the steps I found for basic jump-start I did the following: Modprobe zaptel Modprobe wcfxo Modprobe wcfxs Edited

I have installed FC3 using the notes from lesnet http://www.voip-info.org/tiki-index.php?page=Asterisk+Fedora+Core+3 It worked very well, worked first time. My configuration consists of: (1) TDM400P w/ 2 FXS daughterboards and w/1 FXO daughterboard I use yum update to update my installation. After the update and reboot, I attempted to recompile zaptel, Zapata, libpri, asterisk. No errors,

Hi all, i've installed AMP and Asterisk following the INSTALL file and i have a problem with the TDM04B with 4 FXO: [root@srvoip ~]# ztcfg -vv Zaptel Configuration ====================== Channel map: Channel 01: FXO Kewlstart (Default) (Slaves: 01) Channel 02: FXO Kewlstart (Default) (Slaves: 02) Channel 03: FXO Kewlstart (Default) (Slaves: 03) Channel 04: FXO Kewlstart (Default)

Hi, I've been trying to get my zaptel x100p cards working for the past week now. this is what I've done: installed asterisk: make clean make linux 26 (for fedora core 2) make install installed zaptel: make clean make make install did a modprobe zaptel, and wcfxo got this in /var/log/messages: PCI: found IRQ 11 for device 0000:00:0f.0 wcfxo: daa mode is 'FCC' found a

Hello, I have found a "bug", I think in the way TDM400P cards handle FXO interface disconnect/re-connect problems. Normally I do keep all the wires connected from my CO / PABX quite securely, but I had a need to re-route the cable from one side of the desk to another, and I simply disconnected the RJ-45 connector and plugged it back in. THIS PROMPTLY RESULTED IN VERY VERY SCRATCHY AUDIO

Hi, We installed the latest 1.4.24 on a test machine and can't get zaptel nor dahdi compile. It's a Linux Debian Etch. Errors we have: keewi:/usr/src/dahdi-linux-2.1.0.4# make make -C /lib/modules/2.6.18-custom.2/build ARCH=i386 SUBDIRS=/usr/src/dahdi-linux-2.1.0.4/drivers/dahdi DAHDI_INCLUDE=/usr/src/dahdi-linux-2.1.0.4/include DAHDI_MODULES_EXTRA=" " HOTPLUG_FIRMWARE=yes

Hi, Sorry, in my last mail I wrote "wcfxs" instead of what I actually used, "wcfxo." I just got two digium x100p clones and installed asterisk on fedora core 2 which took some tweaking. After getting asterisk up I installed the zaptel stuff - then modprobed zaptel, wcfxo, which worked fine. ztcfg is showing two channels configured, but when I start asterisk and

Of course I am not a kernel expert, so .. please be patient. I am investigating on my zaptel/zapata problem. As the main error message asterisk quits on mentions <'/dev/zap/channel': No such file or directory> I went peeking over there. [Asterisk Verbose Error Mar 13 20:43:35 WARNING[5779]: chan_zap.c:763 zt_open: Unable to open '/ dev/zap/channel': No such file or

i am using RH8.0,when i try to load the zaptel driver using "modprobe zaptel" it give an error "cant locate module zaptel" also when i do "modprobe wcfxo" it gives "can't locate module wcfxo" when i try compilling zaptel i get "make ***[zaptel.0] Error 1 what am i doing wrong someone please help! -- Augustine GDES 18b oshin road,kongi

Hi list! I have been experiencing a lot of mystical hangs on my box. At first I suspected bad memory or motherboard but I found out that the mystical hangs disappear when I do not load the drivers for my x100p. The box will only hang under high load (copy operations with 30Mb/sec to a raid array in the box for example). With little or no load the box will stay up forever. (The imposed load

Hi, I'm wondering why zttest shows Best: 99.976 -- Worst: 99.967 -- Average: 99.971469, Difference: 99.971469 Shouldn't it be 100% as timing is hardware and comes from PRI? Am I missing some kernel config? Regards, Atis My /etc/zaptel.conf is span=1,4,0,esf,b8zs span=2,3,0,esf,b8zs span=3,2,0,esf,b8zs span=4,1,0,esf,b8zs #lspci 07:03.0 Communication controller: Digium, Inc. Wildcard