similar to: Help on legacy hardware.

Has anyone found an inexpensive E&M trunk card that will play with *? Looking for an interface to a legacy electromechanical PBX that's able to pass answer supervision. Docs on the X100P card would be helpful, we could probably pull E&M out of that. Any ideas?

(refers to posting "Samba 3.0 + ADS, winbind problem" from August, 28th) Setup: client: SuSE8.2 professional (kernel 2.4.20-4GB) with openldap2 2.1.12 and heimdal kerberos 0.4e from the SuSE CDs and Samba 3.0.0RC3 compiled from source with flags "--with-ads --with-pam --with-acl-support". server: Windows 2003 Server as Active Directory Controller (configured as pure

Just wanted to thank everyone for helping me get my new machine up and running. I thought I had bought a boat anchor. Not sure what's up with my DVD drive on my 5.7 machine but I will be phasing/retiring it out over the next few days. Again thanks for your help and most of all your patience. Eddie

thanks for the head up. what os are you running on the blades?? Phillip James System Administrator The Garden City Group, Inc. 105 Maxess Road Melville, NY 11747-3836 Phone: (631) 470-5044 Fax: (631) 940-6561 E-mail: Phillip.James at GardenCityGroup.com ==================================================== This communication (including any attachments) is intended for the use of the intended

Greetings all; I pulled a Belkin F6C100-4 into the shop this afternoon, deader than a door nail. Out of service for about a year because (I'm assuming here) that the cooling fan stopped and cooked what little remaining life there may have been out of the batteries, which had swelled so badly I had to split its frame to get them out. They are also in the under 1 volt per 12 volt pack

I have installed samba for the first time and I try to start it in a windows 95 environement. I started nmbd and smbd with the config file listed at the end of this mail (I remove all comment for clarity) I expect to use samba with the SHARE protocol of Windows 95 (No WINS) The new server (sdmpcsv02) is recognised by the other pc's but the can list the exported files The smbclient -L

Maybe one of you can help me with this: We have T1's that come from both MCI and Global Crossing as uses channelized (24 Ports per T) with inband (DTMF) ANI and DNIS delivery (format = *DNIS*ANI*). My old equipment was set for D4, AMI, SF and Wink Start and so is Asterisk Server. I've moved these T's to Asterisk TE410P and inbound calls are arriving to external voice mail

Maybe of you guys know the answer to this: We have T1's that come from both MCI and Global Crossing as channelized (24 Ports per T) with inband (DTMF) delivery of ANI and DNIS (format = *DNIS*ANI*). My old equipment was set for D4, AMI, SF and Wink Start and so is Asterisk. I've moved these T's to Asterisk TE410P and inbound calls are arriving to external voice mail system

Maybe of you guys know the answer to this: We have T1's that come from both MCI and Global Crossing as channelized (24 Ports per T) with inband (DTMF) delivery of ANI and DNIS (format = *DNIS*ANI*). My old equipment was set for D4, AMI, SF and Wink Start and so is Asterisk. I've moved these T's to Asterisk TE410P and inbound calls are arriving to external voice mail system correctly

I could only get *ANI*DNIS* working one way and that was setting my signalling type on the Asterisk side to 'featd' The Definity won't send *ANI*DNIS* information back to the asterisk as far as I can tell. Other than that, I've been running it with wink/wink E&M for a while now. TN464 circuit pack on the definity side, te110p on the asterisk side. Just a crossover cable

When I send a call from my TE410P using E&M, the legacy PBX answers the call but doesn't route it. Any idea what this could be? I assume the digits aren't being delivered properly to the legacy pbx. Any suggestions on what config settings to muck with? Asterisk SVN-branch-1.2-r40901 built by root @ pbx04 on a i686 running Linux on 2007-01-14 14:05:02 UTC zaptel.conf

I am trying to make an in/out trunk group comprised of 4 DS0's using E&M Wink signalling. The first four channels of a DS1 on a T100P are being used for the group. Outbound calls work fine, but inbound calls fail. The other 20 DS0 channels are used for a PRI. Does the configuration shown below look okay? I've tried setting 'immediate => yes' without success, but it

We're having some difficulty connecting a T1 fax board card to asterisk, with E&M Wink. We've successfully connected it to other E&M Wink T1s, but have been unable to get asterisk to hear it's dialing. Asterisk can dial down to it with no problem, and it hears all the digits, but whenever it sends digits down to asterisk, * always only "gets" the first one. This is

I need to create a couple of tie lines between a legacy system and an Asterisk system. I was told that the tie lines are E4 Superframe E&M. I have done E&M wink but have no idea about E4 Superframe E&M and Google is not helping me here. Does anyone know about this type of signaling and if Asterisk can handle it? Thanks, Steve

I'm a bit confused about how to handle this. I have Asterisk sitting in the middle between a Qwest Long Distance T1 (Voice T1, D4, SF, AMI) and an external voice mail PC using a Dialogic D/240SC-T1 card. The Qwest T1 originally was connected to the Dialogic card directly. The signaling was set to E&M Wink Start because Dialogic used this as its default settings, so it just worked

All, One of our customers is using a Telrad PBX, we are providing phone server through asterisk via a T1 using e&m directly connected to the Telrad system. We're using a T1 cross cable as normal, the T1 part works great. No alarms. When we try and dial out the Telrad using a direct trunk group, the call fails. When looking in the asterisk console I noticed only 1 or 2 digits are seen,

Hi all I have a server that has two TE412P (T1/E1+DSP) cards installed. One of them configured as an E1 PRI connected to PSTN and another one configured as a T1 E&M connected to Avaya PBX. Each card only uses two ports, so there are 2 E1 lines and 2 T1 lines connecting to this server. The purpose of this server is as a TDM trunk gateway that gets call from E1/T1 and then forward to an IP-PBX

I have a problem which I need to resolve. We are trying to put an asterisk between a Mitel PBX and the world. We are adding Voip service via Asterisk. Here is are config files for the settings but our problem is the following. We are able to send calls to the Mitel pbx and it's the T1 connections is green saying it's ok. The support department from Mitel said that they use e&M and

Hi all, I've got a fairly simple setup, a 4 port zaptel T1 card with 1 PRI and 2 flat e&m T1's coming into it, and its working perfectly except for one small thing. When people dial any of the numbers on either the PRI or the T1 from outside of the pbx, they dont get the "ringing" sound. It just directly connects the call. I know this isnt much, but its started to

I've been through Samba 3 HOWTO and the RedHat Knowledge Base, and can't quite get everything going with winbind and Samba. Redhat is RHEL Version 3, update 2 (Version 3.0.9-1.3E.5, per RPM); Domain controller is running in "Mixed" mode. First, the setup: >From smb.conf: workgroup = JJS-SDM netbios name = geneva server string = geneva security = domain encrypt passwords =