similar to: Configuring Digium TE405P for use in Germany

Hello all, the scenario: Carrier ----S2M------ * -----S2M------Siemens | | SIP Clients and many other features With much help from the list, the PRI links are without alarms and inbound calls are working fine (from both: Carrier and Siemens). But I am not able to dial wether outbound nor to the Siemens PBX. I allways get the message: == Everyone is busy

Is there anyone successfully using the TE410P with a German "PMX-Anschluss"? Please just drop me a note mentioning the carrier you use. We are having problems making the card work, although configuration is correct (Posted this before). Our carrier blames the card for this. We would just need some evidence that it really works. Thanks, Henrik -------------- next part

Hallo all, I am trying to get * with chan_capi and a ptp-ISDN with 4 lines on a AVM C4 card to work. But weather inbound nor outbound is working :( My capi.conf: ; ; CAPI config ; ; [general] nationalprefix=0 internationalprefix=00 rxgain=0.8 txgain=0.8 [interfaces] mode=immediate isdnmode=ptp msn=8993 incomingmsn=* mode=immediate controller=1,2,3,4 softdtmf=1 ;accountcode= context=demo

Hello, we have a PRI (E1) to a carrier and a second one to a legacy PBX: DTAG ---pri---- * ------ Hicmo (PSTN) | | Sip and more Many normal inbound calls are direcly routed to the hicom. Outbound calls from the Hicom go through LCR and then to PSTN. Inbound faxes are working, but outbound faxes from hicom to pstn are

Hi all, * was running ... I have a WT405P and an AVM C4 with chan_capi 0.3.4a Today chan_capi stopped working, without any changings at the system. It seems, that not * is the reason, because isdn-log also shows no calls. If I try to call * from outside via capi, I only get a busy. That is the try from inside to outside: stern01*CLI> -- data = @89930:0107901723168212 -- capi

Hello all, I am trying to connect asterisk to a Siemens Hipath 3750 PBX system. I have a physical connection issue. I know that I should use a crossover RJ48 cable to link the two systems. The problem however is that the physical interface of the Siemens system is very unfamiliar. From my digging around, I think that this is an S2M interface. http://www.mail-archive.com/asterisk-users at

Hello, we had a running configruation where asterisk passed the phone number and the ddi to the pstn (i.e. 595-431) Now only the rootnumber arrives: 5950 I do not know, what to do. I tried to use callingpres (now i am just hiding every number, because 595-0 is no valid extension..) but that did not worked. > Protocol Discriminator: Q.931 (8) len=44 > Call Ref: len= 2 (reference

Hi there, today I made the German language prompts available for download: http://www.karl.aegee.org/asterisk.nsf/HT/sound-de Be aware: Asterisk doesn't yet fully support languages other than English, there are still (smaller) issues with voicemail and date/time announcements that require a patch. Cheers, Philipp

Hello, I am using chan_capi 0.3.5 and Asterisk CVS-v1-0-12/29/04-15:32:48 on a SuSE Linux 9.0 with Kernel 2.4.21-99-default In the system is a AVM C4 with one port connected to PSTN at PTP BRI and another one to an ISDN PBX with an PMP BRI. The system is running fine, but I have regualary this error, and then chan_capi is not working anymore. Jan 18 15:29:46 WARNING[2919]: Avoided initial

Hi all, Does somebody know how I have to setup my TE405P ? Is it correct my configuration below ? Otherwise, can somebody help me ? Thanks, Angel. zaptel.conf span=1,1,0,ccs,hdb3 span=2,0,1,ccs,hdb3 span=3,0,1,ccs,hdb3 span=4,0,1,ccs,hdb3 bchan=1-15 dchan=16 bchan=17-31 bchan=1-15 dchan=16 bchan=17-31 bchan=1-15 dchan=16 bchan=17-31

Hi there, our old pbx contract will expire soon and we have now 2 pbx companies trying hard to sell us a new VoIP one. I am usually a friend of open source software and read about the Asterisk poject, but I can not assess if Asterisk fulfills all our requirements. It would be great to receive some input from experienced users to be able to convince our management. My question is if the

Hi, I am looking to integrate Asterisk with a Siemens HiCom 150e via BRI and wondered if anyone is able to offer any advice. In simplistic terms, my goal is to pass calls from the HiCom to the Asterisk box. e.g: HiCom user dials access code and can call Asterisk extension or establish SIP call over Internet. Likewise, I'd like Asterisk to be able to present a call to the Hicom, either

Hi all, A new version of DIAX (0.9.8a) is ready to be downloaded from the following locations: http://www.laser.com/dante or http://www.geocities.com/tdanro What's new in 0.9.8a: - unconditional autoanswer or based on CallerID (user configurable); - use any Ericsson/SonyEricsson GSM/PCS to control DIAX (feedback on the phone display) through Bluetooth (or serial cable). You do not even

Hi * :-) I found in the online WiKi docs some information on how to integrate Asterisk with "old PBX"... http://www.voip-info.org/wiki-Asterisk+legacy+integration ...but I couldn't find anything on integration with a Siemens HiCom 150E. Later on we'll migrate to a HiPath 3750 so information covering this model would be nice too... Do you know if any of the PBX listed

Hi, I installed Asterisk with CAPI support. Everything works fine while starting Asterisk, but when a call comes in Asterisk hangsup the call after two times of ringing. The output is like: Jun 24 22:19:49 NOTICE[1082178480]: chan_capi.c:1931 capi_handle_msg: CONNECT_IND ID=002 #0x011d LEN=0048 Controller/PLCI/NCCI = 0x101 CIPValue = 0x10

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi! I am having problems with the PlayTones application and VoIP softphones. I have the following in my extensions.conf: exten => 123,1,Answer exten => 123,2,PlayTones(Busy) exten => 123,3,Hangup But when I connect with gnophone(IAX) or kphone(SIP) and dial 123 the call just hangs up immediately. I get the following on the console: --

hi, i'm having problems getting asterisk spliced between an E1 PRI (german Telco Arcor) and an Ericsson Business Phone 250 digital PBX. The Asterisk Server has a TE405P with it's port 1 connected to the E1 PRI provided by our telecommunications provider Arcor and port 2 connected to the E1 PRI of our Ericsson BP250. the setup before: Arcor TelCo PRI(E1)

Hi, Is is possible to implement this: Hicom150 --- BRI (QSIG) ---- Asterisk I've been reading Siemens documentation and they say: "Digital nailed connections Corporate communication networks can be implemented over digital S0 or S2M nailed connections between several Hicom systems using the CorNet N protocol and between Hicom and non-Siemens systems using the QSig protocol. The

We originally purchased a TE405P so we could connect our Asterisk server directly to the T1 PRI from our provider, however due to all the problems reported with T1 PRI's interacting directly with Asterisk, we scrapped that idea and decided to stick with our Cisco router making the conversion to SIP. Anyways, we found a new potential use for it. We have an old location with an existing PBX,

Im having a problem getting the 2 cards working together. I added the TDM with 3 FXO and 1 FXS board. The TE405p is working fine. THe TDM registers and identifies the FXO's and FXS but cant get them to go off hook. I hope someone can help. Asterisk seems to THINK its dialing it sends manager status as dialing, and it just sits there with no tones, on the phone dialing out. If I dial,