similar to: UK ISDN PRI Problems

Chris you might know the answer to my HUUUUUUGE problem A few weeks ago you posted this message: "I have an ISDN PRI supplied by NTL (ex Diamond Cable, Nottingham) which is currently working happily with an SDX Index phone system. I have to replace this phone system shortly and I've been trying to get a * system working for some weeks now. I have configured the dial plan (which works)

hi eveybody, after many test with your help and the irc channels help, i get the led on TE110P green with this config: span=1,1,0,ccs,ami =====> alarms OK Green Led but the provider say that i have to set my span to this span=1,1,0,ccs,hdb3,crc4 =====> alarms: YEL/RED i can't make call's yet to test because they have to sync the Modulator in the other side so any remark? is my

<P>hi Everyone,</P> <P>We are configuring an ISDN PRI E1 with an E100P card, when you load the drivers, and starts the asterisk, cards also starts fine, givin following output,</P> <P>*CLI> <BR>&nbsp; == D-Channel on span 1 up<BR>&nbsp;&nbsp;&nbsp; -- B-channel 1 successfully restarted on span 1<BR>&nbsp;&nbsp;&nbsp; --

Hi, Can someone send me a sample on how to get an E400P working with ISDN PRI signaling? What conf. files must I edit? thanks in advance Eduardo

Hi Just received my spanky new TE405P today to replace my Cisco gateway... After much fiddling (I forgot to switch it to E1) I got it to work and everything "seems" to work perfectly on our ISDN PRI. If I dial-in from the PSTN to a SIP phone, the call goes through and if I hangup either the SIP phone or the remote end, the call gets disconnected and destroyed However, if I dial-in

Hi All, This is our 2nd E1 client that we try to use crc4 either with the e100p or with the e405p without luck. After some trials, we ask the telco to switch off crc4 on their side and everything works flawlessly. Is there anything in the crc4 calculation that may be broken? We took a look at wct1xxx.c and wct4xx.c but there doesn't seem to be much there to be fixed (apparently the crc4

Hello ml, i need some help on my zaptel configuration. My E100P only shows some YELLOW / RED alarm when I load the wct1xxp module and do a cat /proc/zaptel/1 Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3/CCS YELLOW RED ... .. . My /etc/zaptel.conf is: span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=nl defaultzone=nl I tried zaptel-1.0RC2 and the latest CVS

Hi, I'm installing E100P for isdn pri line. My configuration are like this. zaptel.conf ======================================= span=1,0,0,ccs,hdb3,crc4 loadzone = us defaultzone=us bchan=1-15 dchan=16 bchan=17-31 zapata.conf ================================================= [channels] context=default switchtype=euroisdn context=default signalling=pri_net usecallerid=yes

Well I'm slowly learning my way around asterisk although as yet I haven't had the chance to actually hook the system up to an ISDN line. I am going to migrate from an Argent Office setup. My only problem is keeping costs down on the phones. The Argent system is running about 30 POTS phones. Can someone suggest the cheapest option? Should I get some kind of large scale FXS box or would

hi, I'm trying to configure my newly acquired TE410P card to work as 4 E1 spans. This is supposed to be a drop-in replacement to the earlier E100P card. However, on loading the zaptel module it gets configured as T1 spans basically doing a 'cat' on /proc/zaptel/1 thru 4, it shows 24 channels per span. After this ztcfg fails saying 'ZT_CHANCONFIG failed for channel 97'.

I am trying to use TE110p card for Euro ISDN with Ericsson AMS switch. I consistently get one of the following errors: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 or PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 My zaptel.conf file: -------------------------------- span=1,0,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 loadzone=us defaultzone=us

Hi whatever I set the span line to in zaptel.conf ie span=1,0,0,ccs,hdb3,crc4 span=1,1,0,ccs,hdb3,crc4 span=1,2,0,ccs,hdb3,crc4 zttool always shows Sync Source: Internally clocked surely this cannot be correct.

Hi list, I'm trying to setup an asterisk 1.8.0 with MFC/R2, but I'm having these error messages loading chan_dahdi: > module load chan_dahdi.so ERROR[9241]: chan_dahdi.c:11848 mkintf: Signalling requested on channel 1 is MFC/R2 but line is in ISDN PRI signalling ERROR[9241]: chan_dahdi.c:16180 build_channels: Unable to register channel '1-15' I got the config in

I have my peers registered to SER.asterisk seems to be sending mwi for the peers seen in the sip show peers CLI command. i have my ser server registered with asterisk as a type=friend and all clients register to ser.how do i get mwi to work for these clients registered to SER. Thank you, -AA

Hi, I have a digium card (igium, Inc. Wildcard TE405P quad-span T1/E1/J1 card 5.0V (rev 02)) 4 ports I want to make a loop test between digium card E1 to test the configuration of dahdi What I want to do scenario is I connect port 1 and port4 in the digium card with E1 cable SIPcall-->E1 Digium port 1--->(Loop)E1 port 2---->sip extension local. kindly can any can help me to

Ok Guys, I've done a tonne of hunting around on this problem, but can't find much help. I'm running: asterisk 1.4.19.1 libpri 1.4.3 and zaptel 1.4.9.2 which I believe has been modified by RedFone to add the ztd-ethmf module. My interface is a RedFone foneBridge2 4 Span; and I'm connecting to a BT E1 PRI / ISDN30e with 15 lines on span 1, and a legacy Panasonic PBX on span 4. Upon

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello List, since some days i run into the problem that one span on a TE407P is not comming up correctly. With intense debug on that span i get: < [ 02 01 7f ] < Unnumbered frame: < SAPI: 00 C/R: 1 EA: 0 < TEI: 000 EA: 1 < M3: 3 P/F: 1 M2: 3 11: 3 [ SABME (set asynchronous balanced mode extended) ] < 0 bytes of data

I have 7965 and am trying to convert the firmware to SIP (SIP45.8-3-4SR1S). Does anyone have a valid XMLDefault.cnf.xml they could share? I have tried the version at voip-info<info.org/wiki/view/Asterisk+phone+cisco+79x1+xml+configuration+files+for+SIP&view_comment_id=14768#Troubleshooting>for the 7941/7961 but unfortunately /var/log/messages shows in.tftp stops sending after

Hi, I try to connect my asterisk box with a classic pbx (Siemens). I have a T100P E1 card. modprobe zaptel and wct1xxp ok ztcfg -vv ok I can run asterisk and show the channels but the led still flash red My zaptel.conf : span=1,1,0,ccs,hdb3,crc4 bchan=1-15 bchan=17-31 dchan=16 My zapata.conf : ;; E1 switchtype = euroisdn signalling = pri_net group = 1 context=e1 channel => 1-15,17-31

Hi To troubleshoot FreeBSD panics triggered by ISDN load on an asterisk system, we are looking to buy an ISDN call generator/simulator device. The minimum requirements include: - Not too expensive - PRI support (BRI support is a plus) - CCS+CRC4 farming + HDB3 coding - EuroISDN (DSS1) support. - A minimum of 4 ports (120 channels/concurrent calls) - Compatibility with Digium cards. - DUT in TE