similar to: Polycom registration

Does anyone keep a known telemarketer caller id database? If not has anyone proposed an Asterisk community project to share this information? Sort of a nation wide blacklist so Asterisk'ers can cut down on the garbage calls... -------------- next part -------------- An HTML attachment was scrubbed... URL:

i have error in install module of tor2. but it compile good. what happen ? ivr2:/usr/src/zaptel # make clean; make install rm -f torisatool makefw tor2fw.h rm -f zttool rm -f *.o ztcfg tzdriver sethdlc rm -f zonedata.lo tonezone.lo libtonezone.so.1.0 *.lo rm -f gendigits tones.h rm -f libtonezone* rm -f tor2ee rm -f core cc -I. -O4 -g -Wall -DBUILDING_TONEZONE -DSTANDALONE_ZAPATA -c -o

I feel I'm on the verge of setting up a pbx for handling internal calls only... The last problem - I think - I've run into is w/ the phone registration running asterisk -vvvc I get a bunch of messages looking like so Apr 6 14:46:05 NOTICE[1116957488]: chan_sip.c:5623 handle_request: Registration from 'sip:2001@192.168.22.254' failed for '192.168.22.1' Apr 6

Hi, I have two WCT100P cards installed on a suse 9.0 box. Installation for Zaptel complains of some unresolved dependencies. The zaptel and wct1xxp modules load without any errors. ztcfg give no problems. The problem is when I start asterisk I get the following error and asterisk shuts down

I just received my dev kit and installed the hardware. I followed the directions Digium sends out to the letter and when I ran modprobe tor2 I got the following error: /lib/modules/2.4.18-19.7.x/misc/tor2.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the

Anyone out there have the AudioCodes MP-108 working with Asterisk? I am able to get the channels to registers with Asterisk, but anytime I try and send a call I receive these error messages: Jul 6 15:12:10 DEBUG[1133742896]: chan_sip.c:771 __sip_ack: Stopping retransmission on '117801284512845hUxv-9991110061--17708185305@63.201.117.76' of Response 20587: Found Jul 6 15:12:10

Hi guys, Thanks for your answers on my two questions yesterday. That's exactly what I was looking for, sorry for not noticing it myself, but I'm still getting acclimated to Asterisk and even Linux--from what I see so far, I love it. I've got another one now. Since my Asterisk install and configuration is fairly stable at this point, I'm interested it ensuring that during

Hi! I have just bought the X100P and TDM400P cards to install on my computer to implement the PBX. I also downloaded the newest softwares asterisk_ver0.5.0, libpri_ver0.4.0, and zaptel_ver0.7.0) to install on my computer (Red Hat Linux 8.0). All packages are compiled well. When I use "modprobe" to load drivers (modprobe zaptel, modprobe wcfxo, modprobe wcfxs), the first two (zaptel,

Hi, all I am trying to install E100P card, the 'modprobe zaptel' is ok, but when I did 'modprobe wct1xxp', I got such error, so can not load the driver for the card. /lib/modules/2.4.20-8/misc/wct1xxp.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog

Just cross pairs 1-2 and 4-5 1 <--> 4 2 <--> 5 Never done an E1, but I think it's the same for a T1 4 wire cable. Tim Thompson Commercial Sales Engineer http://www.amatechtel.com (806) 722-2227 -----Original Message----- From: bam [mailto:bam@cqm.co.uk] Sent: Monday, December 29, 2003 9:12 AM To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] E100P pinouts

Hi All, I wish to connect * to a Cisco using a E100P board. When I load the driver I got this error message: -bash-2.05b# modprobe wct1xxp ZT_CHANCONFIG failed on channel 1: Function not implemented (38) /lib/modules/2.4.21-SAX/misc/wct1xxp.o: post-install wct1xxp failed /lib/modules/2.4.21-SAX/misc/wct1xxp.o: insmod wct1xxp failed Follows Cisco configuration: isdn switch-type primary-qsig

Hi, I am trying to set up * and ISDN-PRI (channels 1 - 15) using E100 boards. I installed zaptel and libpri. When I execute modprobe -r wct1xxp I get an error message: ZT_CHANCONFIG failed on channel 1: Function not implemented (38) /lib/modules/2.4.21-SAX/misc/wct1xxp.o: post-install wct1xxp failed /lib/modules/2.4.21-SAX/misc/wct1xxp.o: insmod wct1xxp failed Follows my /etc/zaptel.conf:

In my * server I have a T100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm on the card starts blinking red. Running zttool confirmed that yes, it is a red alarm. I've read a few previous posts on this type of setup and I'm not too much closer. What should I be checking next? A different cable? The

Hello ml, i need some help on my zaptel configuration. My E100P only shows some YELLOW / RED alarm when I load the wct1xxp module and do a cat /proc/zaptel/1 Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3/CCS YELLOW RED ... .. . My /etc/zaptel.conf is: span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=nl defaultzone=nl I tried zaptel-1.0RC2 and the latest CVS

Hi, i just received an E100P, this is the first one I have ever seen, and notice that the board reads T100P. Is this right ? The antistatic bag had a small label that has E100P written on it, and the card is a bit different than the T100P I already have, Does Digium use the same boards for both cards ? I don't have an E1 link here, can I test the card just by loading the driver and run

We connected an * box with an e100p to an E1/PRI from a telco here in Italy. After we had it working perfectly the telco told us that, despite the circuit appeared to work fine, and we could place calls on it, they had an "E-bit2 alarm indication constantly on that caused the circuit to be flagged as "faulty" every time. (The E-bit indication, is an alarm sent back from us to

Hi, I have a 1 port T1 card in an asus p4p800-vm board with a 2.0g Celeron, and 512m of 266mhz ram (256 on each channel). This board has video, Ethernet, and serial ata all on-board, I got it because of that, there wouldn't be anything else on the pci bus that would mess with the zaptel card(s). So, here's my problem. I'm running redhat 9 with kernel 2.4.20-20.9. I can load the

I have just received a T100P and an Adtran TSU 600 in the mail. I seem to be having a problem with the T100P card. So far I have done the following: vi zaptel.conf fxoks=1-22 fxsks=23-24 ... vi zapata.conf ... signalling=fxo_ks ... channel => 1-22 ... signalling=fxs_ks ... channel => 23-24 I then run modprobe zaptel modprobe wct1xxp ztcfg -vv There are no errors to report. In

hi all i have a te110p installed in my system with a lot of Echo.. i decide to install the oslec echo supressor but when y try to add the module i have this problem. [root at asterisk zaptel-1.4.7.1]# insmod wct1xxp.ko insmod: error inserting 'wct1xxp.ko': -1 Unknown symbol in module [root at asterisk zaptel-1.4.7.1]# some advice? thanks. -- .-

hi, i got he following error while trying to install digium cards in red hat linux 7.3. please help. [root@localhost root]# modprobe zaptel lib/modules/2.4.18-3bigmem/misc/zaptel.o: unresolved symbol cpu_raise_softirq_Rd01f3ee8 lib/modules/2.4.18-3bigmem/misc/zaptel.o: unresolved symbol ppp_output_wakeup_Rcb5deb89 lib/modules/2.4.18-3bigmem/misc/zaptel.o: unresolved symbol