similar to: AW: IP Phones that support G.723 on H.323

Hello, I think I have the same problem as Martin Bene mentioned in http://lists.digium.com/pipermail/asterisk-users/2004-January/034521.html Since I found no further information about this I'd like to ask wether you know what the reason for this problem is and how one can get around this. * is registered to the innovaphone gatekeeper. Trunk connection is done with an AVM-B1 and chan_capi.

Hi Siggi/Jan, >If so, there's still a load version conflict (although I've >never seen a >7960 or 7940 care about the version communicated through SCCP): > >On the phone, press "Settings", then 4 for load information. >watch out for the "App-Load-ID". On my 7940, this is >"P00305000300". Yours >is most likely a smaller number... >

Hi, I'm trying to get h323 communication working between asterisk (0.7.1) and Innovaphone Gatekeeper + innovaphone phones. chan_323 installed OK with currently recommended pwlib_1.5.2 and openh323_1.12.2. Registration asterisk with the gatekeeper works OK, externsion for my test(sip) phone gets registered with gatekeeper. when establishing a call between a h323 phone and asterisk I run into

We're using a couple of h323 IP Phones (innovaphone ip200) w/ asterisk. Basic call setup works, but we can't get call transfers to work: On pressing the "transfer" button on the phone (getting a new dialtone) the 2nd endpoint is disconnected. Any idea if we can get this to work? Same reaction using the innovaphone ip400 gatekeeper and using gnugk. Asterisk version is 0.7.2

Hi, we intend to use innovaphone's IP200 full standard compliant H.323 hardware phones (great!) with asterisk. Everything works perfect (calls, signalling, talking) until we want to perform a call transfer (H.450). Upon pressing the R-key the first connection is hung up immediately. As gatekeeper we use a IP400-box OR GnuGK, same result with both... So, who has experience or uses

Hello everybody, I?ve been trying to solve a problem for several weeks now but it really beats me. There are several hard phones connected to an Innovaphone 3000 VoIP gateway. On the other side I have a SIP softphone connected to Asterisk. The problem I have is that on incoming calls (hardphones to softphone) I only have outgoing audio (from soft to hardphone); everything is OK when I call the

Dear all, Can someone from Netherlands who has SPA3000 send me the Regional & Line1 settings. I'm not sure what is wrong but I can call from asterisk to phone attached to spa300 FXO, but not the other way. I tested three phones: siemens gigaset, tiptel 160 and hpoj k80(fax). Only tiptel 160 can call to the asterisk, other two just dial but nothing happens. I guess this has something with

Is anybody familiar with these IP phones AT-723 or AT-323 I think it is made by this company: http://www.atcom.com.cn/at723E.html -- #Joseph

Hi, > I've never run against a commercial PBX that didn't need > maintenance. Acknowledged. > VM hard > drives fail, > ... > Asterisk is > every bit as stable > as the old-gen KSUs and PBXs. There are big differences. As I know of no other PBX that uses 'consumer' hardware, asterisk is also struggling with problems in the underlying Hardware. And

Hi, I'm using a Cisco ATA186 and iConnect to complete PSTN calls to the US. I've noticed that when I set the Cisco ATA to use LBRCodec to 0 (g.723 instead of g.729), AudioMode 0x00150015 and RxCodec, LxCodec to 0, (use g.723) Asterisk will connect to iConnect, successfully natively bridge the call and then about two seconds later not just drop the call, but terminate unexpectedly.

I have asterisk connected to E1 interface with Digium TE110P. I have Cisco ATA 186 and fax pass thru well. I have tried to establish modem connection (from computer connected to ATA => SIP => * => E1 => Telco => pstn => another modem) and I do connect (at 14,400) but connection end after a minute. How to establish successfully modem connection? Has anybody tried innovaphone IP21

Hello everybody, I?ve been pulling my hair for a week now over a problem, and I really don?t know where to look anymore. Here?s my setup: There is an Innovaphone IP3000 VoIP gateway on the LAN (10.253.30.254). I can use it to send and receive calls from physical phones attached to it. I have setup Asterisk 1.0.3, with H323 and openH323, and on the same server I also setup GnuGK (10.253.30.1). I

Hi, I have 1 phone it is a 7910 that when I try to make calls it seems to be trying to use g.723. The error I get is cannot find a path from GSM to G723. Am I missing something? Is there a way to set the codec in the phone or in the skinny.conf? I'm stumped -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello, when using BLF with Asterisk 1.6, I notice that the Caller-ID information is not displayed on the monitoring key of my Innovaphone IP200A. If the IP-phone of my colleague rings, I should see on my partner key the number of the caller. This is information that is being send in the xml-body of the NOTIFY-message. I do not see this information in the xml-body of a NOTICE-message from

I hope this doesn't show up twice (posted from wrong mail adr.) Hi Eric, You can actually get boards like this already from companies like Mapletree. Its a hardware pci carrier card where you add the number of DSP modules that you need. This hardware may be a bit 'high end' for most users on this list but several people seems to address this issue pretty often. One card may be

Hi FOlks, I am using for research purposes Kvin's codecs available at http://kvin.lv/pub/Linux/Asterisk/ G729 is working very well but g723 has a very poor audio quality. I recompiled everything with gcc4 and the distro used is Slackware 11. Anyone with some experience on that? Thanks in advance for any help. Isamar Maia +55-71-9146-8575

Stephan, Ok, I'll re-state the problem... I have two devices that I want to talk to each other: 1. an Asterisk PBX 2. a Damm Cellular TETRAFLEX digital radio system (www.damm.dk) both devices are effectively "gateways" because they have many subscribers behind them. The Damm Cellular system controller is based on Windows-XP Embedded and its sub-systems used the OpenH323

Hi Siggi, > > 7960 and then "Call Ended" on the Display (curious about that !!!). > > That seems to be normal for the 7920. I've sniffed the registration > procedure with Cisco's newest 3.3(3) CallManager (+patches), and it's > doing the same thing. Maybe that's some odd way of testing if the > CallManager ("CCM") really works... >

Hi, Want to do some experiments with the G.723 codecs - where can I download the 723 source code for Asterisk? I know there are some ongoing discussion regarding patents and license fees for the g.723 but I have some hardware on which I only have the 723 and need to test it privately. Thanks! Dan _________________________________________________________________ Use MSN Messenger to send

Hi, I just got some interesting information from Kirk Telecom (www.kirktelecom.com). This company has been in the business of providing DECT solutions (IP gateway, base stations, repeaters and handsets) either to be used with Cisco CallManager (SCCP protocol) or with the Innovaphone IP PBX system (H.323). Two important elements: 1. It seems they foresee a SIP version of their product in Q1