similar to: Wildcard TDM400P

I have a TDM400P with one FXO module and two FXS modules in it. I also have a Wildcard X101P. After trying hard to get things working on various Intel computers, but having echo problems that made it not really usable, I decided to try it on some older PowerPC (Macintosh) hardware running Yellow Dog Linux. Things started off smoothly. Both zaptel and asterisk seemed to compile okay, and both

I thought I'd share my Asterisk experience, which hasn't exactly been as pleasant as I would like but now seems usable in most ways and more then I expected in other ways. I wanted a home PBX system, that would let me treat different callers different ways depending on CID. I initially bought the Digium developer's kit to try things out. That's a single port TDM400 and a X101P.

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel

HI, I just installed an additional module to a TDM400P card. Everything worked fine for a while, but after rebooting the server the new channel fails to be recognized by asterisk. Here is the output == Parsing '/etc/asterisk/zapata.conf': Found -- Registered channel 1, FXS Kewlstart signalling -- Registered channel 2, FXO Kewlstart signalling -- Registered channel 3, FXO

An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20031223/62cf404e/attachment.htm -------------- next part -------------- Hello When I tried loading TDM400P module using insmod command, I get following error messages. Is there some problem with my asterisk installation. Please advise. Thanks Tony $insmod wcfxs Using

Hi, I bought the Digium Asterisk Developers kit a few weeks ago, got the x101p and a tdm400p cards, both seemed to be working fine up until today, now the tdm400p seems to have gone to the great PBX in the sky ...... If I left the reciever on the analog phone I don't get a dial tone and nothing appears on the asterisk console, If I use my cellphone and dial in I see Asterisk Ready.

Greetings all, I'm new to asterisk... Finally got two IP phones and two TDM400P's (one with four FXO modules and one with four FXS modules)... Began experimenting a couple days ago and have ran into a very aggrevating problem. My system consists of the following hardware: Abit BL7-RAID motherboard Pentium 4 1.6GHz processor 512MB SDRAM 2 TDM400P cards 2 3Com 3c905

When I try to start up zaptel, whilst running ztcfg, I get the following error: Jan 1 10:48:18 bu ztcfg: ZT_CHANCONFIG failed on channel 2: No such device or address (6) My /etc/zaptel.conf is: fxsks=1 fxoks=2 loadzone = au defaultzone=au Channel 1 is a X101P card connected to the PSTN and channel 2 is a S100U box driving an analogue phone. The zaptel kernel module gets loaded OK as does the

Hi, I have received a new card TDM400P revision E, from digium. When I tried to modprobe wcfxs it gave me the following errors: Freshmaker version: 63 Freshmaker passed register test ProSLIC on module 0 insane (1) 255 should be 2 Module 0: Not installed ProSLIC on module 1 insane (1) 255 should be 2 Module 1: Not installed ProSLIC on module 2 insane (1) 255 should be 2 Module 2: Not installed

The REV I card shows up in the PCI table as: 02:05.0 Network controller: Tiger Jet Network Inc. Intel 537 (or 02:05.0 Class 0280: e159:0001) Subsystem: Unknown device b119:0001 But the REV E/F shows up as: 02:0d.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface (or 02:0d.0 Class 0780: e159:0001) Subsystem: Unknown device b100:0003 One

Hello Everyone, I just got my Dev Kit TDM today... :D I installed the X100P ok (wcfxo); however, when I tried to 'modprobe wcfxs' for the TDM400P(TDM10B), I got this error message: /lib/modules/2.4.19/misc/wcfxs.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters /lib/modules/2.4.19/misc/wcfxs.o:

Hi! I have just bought the X100P and TDM400P cards to install on my computer to implement the PBX. I also downloaded the newest softwares asterisk_ver0.5.0, libpri_ver0.4.0, and zaptel_ver0.7.0) to install on my computer (Red Hat Linux 8.0). All packages are compiled well. When I use "modprobe" to load drivers (modprobe zaptel, modprobe wcfxo, modprobe wcfxs), the first two (zaptel,

Hello I setup Asterisk@Home with purely VoIP and it worked fine. I then added an X100P card so I could call out / take inbound calls via PSTN and that went fine. But I have just added a TDM400P card (specifically a TDM30B) and now problems. Here is some of the output. Any ideas on what I should be looking at next? When I run genzaptelconf -s -d I get lots of erors on screen - bit I can

Let me start by saying no, this is not the normal stupid echo question :) I currently have a SIP device and an X101P, and have had the usual echo issues and have played around with the various solutions, none of which are quite perfect (understandably).. however, my girlfriend is a little more picky than I am when she uses the phone, so I'm considering a Digium TDMXXB card for the house. My

(I'm producing a writeup on all the things one run into building an * box. Which after a couple of boxes is showing up aplenty.) So this uses the working h/w and config's from another box. All I do is build in a new computer. Loading the modules I got: __________________________________________________ Zaptel Configuration ====================== Channel map: Channel 01: FXS

Hi All, Sorry if this has been around a millions times.. I have been off this list for a few months now.. I have installed the latest asterisknow (upgraded asterisk to 1.6 as well) and I am having a hard time getting my X100P and TDM400P working.. Its all new to me with dahdi because my old server is still running Asterisk 1.0.2 so there have been lost of changes.. Can someone point me in

I've just replaced a X101P card with a brand new TDM400P card (specifically TDM421B). I do have the molex plug attached. kudzu removed the config for the X101P OK, but didn't find the TDM400P lspci does not show the card ?? Bung card ?? How susceptible are these cards to XRays, as it has been thru AU customs and might have been thru the scanner. -- Howard. LANNet Computing

A bit about my experience with the TDM-04 FXO. Only saw a few post on this subject, thought I would contribute a little about my experience to save others the hassle. a. As an earlier poster noted, the driver for the FXO is in the wcfxs module. Perhaps it should be renamed to something less confusing. b. You need the zaptel,zapata libraries from the cvs, the ones with Asterisk 0.7.2 won't

Hi; I'm trying to connect a TDM400P with an FXS module to a Valcom V-9940 Paging adaptor. This port on the TDM400P was connected to a 2500 Set and was working I just re-connected it to the Valcom (which is known to work on a Telco POTS line) and its not picking up. The Valcom docs say it need a minimum of 75 Volts at 20-30 Hz to recognize a call... So the question is what ring voltage

Hi all, I have just purchased the DevKit from Digium and received a X100P and a TDM400P (it has one FXS module). The problem is that I can't get the kernel module (wcfxs) to load and run. I have searched the archives and can't find anything about this. Do the messages below ring any bells with anyone ? There is no interrupt clash (see pci list below). I am running on a AMD 1.2G