similar to: Asterisk as office PBX

Hi I've bought the Wildcard TE110 some days ago but I'm unable to get it to work with Siemens HiCom 300. I've tried this so far: 1. I've used standard cat5 cable cut off on one edge and twisted wires 1 to 4 and 2 to 3 which is according to cisco a short circuit for E1 lines. Wildcard takes a few seconds and sets the link to green (OK). 2. I've tried to connect our running

Hi all, I am trying to setup an E100P for use on Swisscom E1-PRI here in Switzerland. Swisscom seems to use Siemens hardware. Here are my configs (cvs from a few hours ago) : zaptel.conf loadzone=fr ; tried "de" but got warning at modprobe defaultzone=fr span=1,1,0,cas,hdb3,crc4,yellow ; Seems to be right, as the Siemens SDSL-G703 modem switches its LEDs off ... not sure

Hi, I try to connect my asterisk box with a classic pbx (Siemens). I have a T100P E1 card. modprobe zaptel and wct1xxp ok ztcfg -vv ok I can run asterisk and show the channels but the led still flash red My zaptel.conf : span=1,1,0,ccs,hdb3,crc4 bchan=1-15 bchan=17-31 dchan=16 My zapata.conf : ;; E1 switchtype = euroisdn signalling = pri_net group = 1 context=e1 channel => 1-15,17-31

I'm considering switching my incoming phones lines from standard analog to a T-1 service from XO communications. They propose to bring in an "IAD" which has 12 lines of voice and 768k of internet bandwidth as part of a package deal. Since I want to keep the voice traffic in the digital domain the equipment they're proposing is a "Lucent Digital Vina Integrator" IAD

Has anyone implemented an outcall notification when there is a voice message waiting? I would like to have the system notify me of awaiting voice messages by a telephone call rather than an email notification. I would imagine that a call could be dumped into the asterisk spool directory, but I'm not sure how I would monitor for messages waiting. Has anyone implemented such a feature for

Has anyone tried a Vina T-1 Integrator as a channel bank with Asterisk? They appear to be plentiful, but I want to make sure I'm not buying a brick. THX/BDH

Hey all, Here''s my situation: I have a pair of controllers with associated models (called Services and Testimonials) that are quite similar. Because their CRUD behavior is executed via AJAX, the "templates" for the actions are all short .rjs files. Now, because of the similarity of the models, most of the templates are exactly the same, with only the object names changed. That

Hi list... I have already installed a small PBX ( 1 FXO (E100P) and 4 FXS (TDM400P) ) but now i want to know how to build a bigger one... maybe 8 FXO and 24 FXS something like that o bigger. But i dont know witch hardware i need. And also any of you have installed Asterisk only for VoIP and connect this with a Normal PBX (Nortell), so that the actual telephone system can dial to the

Dear I have a data.frame, and want to fit a constrained non-linear model: data: x y -0.08 20.815 -0.065 19.8128 -0.05 19.1824 -0.03 18.7346 -0.015 18.3129 0.015 18.0269 0.03 18.4715 0.05 18.9517 0.065 19.4184 0.08 20.146 0 18.2947 model: y~exp(a)*(x-m)^4+exp(b)*(x-m)^2+const I try to use nls() and set start=list(a=1,b=1,c=1,m=1), but which always give me a error message that

Hello ml, i need some help on my zaptel configuration. My E100P only shows some YELLOW / RED alarm when I load the wct1xxp module and do a cat /proc/zaptel/1 Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3/CCS YELLOW RED ... .. . My /etc/zaptel.conf is: span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=nl defaultzone=nl I tried zaptel-1.0RC2 and the latest CVS

<P>hi Everyone,</P> <P>We are configuring an ISDN PRI E1 with an E100P card, when you load the drivers, and starts the asterisk, cards also starts fine, givin following output,</P> <P>*CLI> <BR>&nbsp; == D-Channel on span 1 up<BR>&nbsp;&nbsp;&nbsp; -- B-channel 1 successfully restarted on span 1<BR>&nbsp;&nbsp;&nbsp; --

Hi, i just received an E100P, this is the first one I have ever seen, and notice that the board reads T100P. Is this right ? The antistatic bag had a small label that has E100P written on it, and the card is a bit different than the T100P I already have, Does Digium use the same boards for both cards ? I don't have an E1 link here, can I test the card just by loading the driver and run

Looks like I am going to be doing my first serious commercial install of FreePBX. I DO mean serious. They are willing to put up with a few glitches initially which is why I have decided they will be a good first client. I have turned down several over the past couple years because I just did not feel comfortable with the state of software/hardware. It seems to work much better now. I was

Hi- Perhaps someone with an E100P in hand can answer this: I just received an E100P from Digium (I normally buy quad boards) I noticed that the circuit board says "T100P" on it, and I assume that the T100P and E100P both use the same circuit board. Can someone please confirm that their E100P says "T100P" on the artwork? Thanks Scott Scott M. Stingel Emerging Voice

I need to know how to setup the data side of the T1 on my Linux Box. I have found information about configuring a PRI and HDLC but nothing about the Frame-Relay type setup for data. The following is information from our T1 provider. Network T1: Framing = ESF Line code = B8ZS Build out = 0-133ft(DSX)/0dB(CSU) Clock = network Pulse-density-enforce = off alarm-option = on alarm-delay = 15

hi see below's conversation. it seems the e100p card doesn't work with BT. Any idea how this'll work against Telenor (norway)? roy <RoyK> does anyone know if I can trust the E100P to do full PRI stuff in .no? <cypromis> dunno about no <cypromis> I cannot use it in UK <cypromis> cause the framer has problems with system-x switches at bt

Hey all! I had an experience trying to set up an E1 in Brazil which could help somebody. In Brazil is very common telcos to have just R2 digital as their primary signaling. As I were trying to set up an E100P, which does not support R2 yet, I had to test an other signaling which works perfectly with Asterisk. They call this signaling as RDSI, using ccs as framing and PA (primary access) as

Hi ! I am trying to configure two E100P cards, but I am a bit confused with zapta.conf in what I am trying to achieve. The * will be connected to a pstn switch with two E1 PRI lines. The E1 lines will be used for incoming calls as well as outgoing calls. My problem now is what to put in zapta.conf, I would like to group all channels from both cards together (if that's possible). Does this

Just cross pairs 1-2 and 4-5 1 <--> 4 2 <--> 5 Never done an E1, but I think it's the same for a T1 4 wire cable. Tim Thompson Commercial Sales Engineer http://www.amatechtel.com (806) 722-2227 -----Original Message----- From: bam [mailto:bam@cqm.co.uk] Sent: Monday, December 29, 2003 9:12 AM To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] E100P pinouts

As a follow-up to my previous post where I stated the IAD would be a Vina model, after some more prodding to XO, they have told me it will either be an Adtran TA-600 or a CAC Adit 600. These products are covered pretty well on the web and I have manuals on both. So, if those knowledgeable folks had to use one of these to attach to an Asterisk box, what interface would be best or at least