Displaying 20 results from an estimated 700 matches similar to: "error on IAX1.conf and warning on chan_iax2.c"
2004 Jan 30
1
Help!!!: test Asterisk error: error on IAX1.conf and warning on chan_iax2.c
Hi, all
Please help me.
My platform is RedHat Linux 9.0. I have a wildcard
x100p. I just installed asterisk by following step:
# cd ../zaptel
# make clean ; make install
# cd ../libpri
# make clean ; make install
# cd ../asterisk
# make clean ; make install
# make samples
When I test Asterisk typing
# asterisk –vvvvc
I get one error and one warning:
[chan_iax.so] => (Inter Asterisk
2004 Apr 02
1
error with asterisk -vvvvc
Hi
I?m a new user and I do test with my hardware
.
I have a x100p and telephone vozip.
And when I run this command asterisk ?vvvvc for to test it
.
My computer show it ?warning?
[chan_iax.so] => (Inter Asterisk eXchange)
== Manager registered action IAX1peers
== Parsing '/etc/asterisk/iax1.conf': Not found (No such file or
directory)
Apr 2 07:45:12 ERROR[16384]:
2005 Oct 10
0
Asterisk behaving wierd!!
hello,
I have been using asterisk now for about 2 years now on a RH8.0 it is our
main call gateway.
I have on the box 3 T1 TDM cards connected to 2 Rhino channel
banks (FXS) and 1 CAC Access bank I (FXO) with so many softphones and ATA
186s.
It has been working good till today some few hours ago. i just
discovered that there were no dialtone on the phones.
Asterisk did not spit out any error, it
2004 Jan 30
2
IAX1 vs IAX2 for IAXtel
G'day list,
I am getting a lot[1] of traffic on my Internet link, ICMP messages from
69.73.19.178 telling me UDP port 5036 is unreachable (this IP address
belongs to iaxtel.org).
I see from the wiki that IAXtel supports only IAX2 from December 2003.
Fine, however it looks like my * still wants to try and register using
IAX1, and I can't find how to turn this off.
This situation is
2004 Jun 17
1
Disable IAX1 Registrations
I was just noticing that my asterisk box is trying to register with my
providers on both IAX1 and IAX2. They do register on IAX2, but it seems like
it keeps trying to register with IAX1 also.
Is there a way to disable this behavior, or am I just misunderstanding it. I
just want to make sure I'm not wasting processor time and bandwidth trying to
register IAX1 when it is already
2004 Apr 21
1
About IAX channels
I have been running af Asterisk server Version 0.7.2 for a while now
But I I wanted to upgrade my version to the new 0.9.0 or the CVS 1.0 Stable.
But when I install one of the new asterisk servers I having lots of troubles
with the IAX connection between my servers.
When I start the 0.7.2 asterisk server it shows me something lige this
== Parsing '/etc/asterisk/iax.conf': Found
==
2004 Jun 18
0
Fwd: Re: Disable IAX1 Registrations
Just in case anyone else is looking for this information, I'm posting the
answer here. I do need to double check if this works with asterisk >= 0.9.0.
I've heard rumors that IAX1 support has been removed in newer versions.
---------- Forwarded Message ----------
Subject: Re: [Asterisk-Users] Disable IAX1 Registrations
Date: Thursday 17 June 2004 04:43 pm
From: "Chris A.
2005 Jan 16
1
IAX1 vs. IAX2
I'm still using asterisk v. 0.9 I think it is using IAX1 as the ixa.conf
is set port=5036
Can I register with a provider who is using IAX2 ?
When I set it up and run:
iax2 show registry - it is not displaying any registered provider.
--
#Joseph
2004 Jan 29
0
Suggestions for debugging an IAX1 one way audio problem
Hi,
I occasionally experience a one way audio problem when using the IAX1 protocol
with a service provider. If I call a DID number in by group provided by the
supplier which is redirected to my box, I only get the audio path back from
my box to the phone I used to dial the DID number.
If I use IAX debug, or tcpdump I only see packets going from my box to the
provider when the one way audio
2003 Jun 29
1
SIP only with no soundcard?
Skipped content of type multipart/alternative-------------- next part --------------
[root@LINUXVM root]# asterisk -vvvc
== Parsing '/etc/asterisk/asterisk.conf': Found
Asterisk 0.4.0, Copyright (C) 1999-2001 Linux Support Services, Inc.
Written by Mark Spencer <markster@linux-support.net>
=========================================================================
== Parsing
2003 Apr 28
1
Turning off Bridging?
Hi folks
Is it possible to turn off the native bridging on Asterisk?
I've been hacking about app_disa.c to support account & pin numbers, that tag the calls
depending on who logs in.....
It all works fine, then dials the destination number they requested.
My setup is as follows
[ENDPOINT] <IAX1> [MYASTERISKBOX] < IAX1 > [TELCOBOX]<>(PSTN)
If i dial
2003 May 17
0
error to load chan_iax.so
Hello all,
I tried to compile Asterisk from CVS yesterday.
I would like to try gnophone as IAX client on the same Asterisk server
with a sound card.
I didn't have any problem of compilation.
Here are the config files in /etc/asterisk:
/etc/asterisk/asterisk.conf
/etc/asterisk/extensions.conf
/etc/asterisk/iax.conf
/etc/asterisk/indications.conf
/etc/asterisk/logger.conf
2003 Apr 29
0
segmentation fault at voicemail
Hi,
I would like to express my appreciation to your big efforts. I am enjoying
Asterisk very much.
My Asterisk works very well, but I encountered a segfault at voicemail after
pressing # to end the recording. Please see the log below.
My asterisk is running on RedHat 8.
When booting the Asterisk, I found a WARNING around IAX, and it says "Unable
to open IAX timing interface: No such
2003 Aug 20
1
IAX <> IAX trunking... DP cache?
I'm attempting to get two Asterisk 0.4.0 PBXes to communicate with one
another using IAX/IAX2 trunks.
I've managed to get a semi-functional NAT Firewall working as a PBX
(with Asterisk running directly on the firewall itself), but there are
issues with bind()ing to various interfaces which is causing outbound
SIP issues.
To get around these issues, the idea is to do something like
2004 Jan 09
1
chan_iax2.c Ignoring Port For Now
Hello,
I have searched the lists, and have seen this message posted numerous
times, however there never seem to be any replies to it.
I was curious if anyone had figured out the WARNING:
File chan_iax2.c, Line 5466 (set_config): Ignoring port for now
Everything seems to work just fine, however when I try to change iax.conf
port to 4569 it doesn't seem to like that either.
Thanks,
Brent
2003 Feb 18
1
Asterisk left in a bad state
Hi all,
I'm using asterisk in a production environment now and this afternoon I got
reports complaining that it was not working. Looking at the asterisk console
output, I saw it contains lots of error messages as printed below.
Unfortunately it is not obvious from the logs as to what started all this.
Just before the error messages start, everything seems to be working fine
with no problems.
2003 Jul 09
1
IAX2 Warning
When starting *, I get the following when the chan_iax2.so loads:
[chan_iax2.so] => (Inter Asterisk eXchange (Ver 2))
== Manager registered action IAXpeers
== Parsing '/etc/asterisk/iax.conf': Found
WARNING[16384]: File chan_iax2.c, Line 4980 (set_config): Ignoring port
for now
== Registered channel type 'IAX2' (Inter Asterisk eXchange Driver (Ver 2))
== Using TOS
2004 Apr 05
0
Segmentation fault, exit status 139, ...
Hi!
I am running an * 0.7.2 on an X86 debian stable 2.4.25 (with
backports.org). The HW I am using is Digium's E100P on an HP DL 380.
Quite often it crashes, e.g. after a call has finished. Below some logs
form the * Console as well as from the /var/log/asterisk/messages
(Replaced some stuff with XXX).
Any idea what there could be the reason for this segmentaion fault?
What other
2004 Apr 07
0
Bug? Asterisk crashes if SIP UA hangs up first
Hi!
As reported earlier this week, I have problems with a sometimes-crashing
Asterisk. In most of the cases safe_asterisk is able to restart it.
But sometimes it crashes, so that manual interaction is necessary.
The seg-faults and crashes occurs, right after call between a SIP Terminal
and a legacy PSTN Terminal (PRI/Euro-ISDN), but only if the SIP Terminal
hangs up as first. No problem, if the
2011 Feb 10
1
Re: nfs undercover
You must update your gaphic card driver.
Yor sistem run defult graphic drver you must update graph.