similar to: Ring/Off-hook Message

Hello, About every 2 or 3 days I notice in the messages log file: Dec 17 08:39:27 WARNING[1220]: Detected alarm on channel 2: Red Alarm Dec 17 08:39:27 WARNING[1220]: Detected alarm on channel 3: Red Alarm Dec 17 08:39:27 WARNING[1220]: Detected alarm on channel 4: Red Alarm Dec 17 08:39:27 WARNING[1220]: Detected alarm on channel 5: Red Alarm Dec 17 08:39:27 WARNING[1220]: Detected alarm on

Check with your telco. We had the same problem on 1 of our PRI's, every day at 5:00 sharp, red alarm, with all calls cut off for 30 seconds exactly. Turns out the equipment at the CO was going into a test loop at that time because of a forgotten setting by a tech. Man, what a finger pointing exercise that was. -----Original Message----- From: Matthew Boehm [mailto:mboehm@cytelcom.com] Sent:

We have been experiencing static noise on one of our phone lines connected to our Adtran Total Access 750 which is then connected to a T100P card. I was convinced that, after rain storms, the static would get worse, it was surely a problem of Verizon's. Verizon sent a field rep out today and he told our secretary (I was busy) that there was a hard ground on the Ring portion of the line.

Hello, I have been researching Echo Can's for a while now, and wanted to post this out to the list to solicit feedback (and if my assumptions are correct, hopefully help others out)... If anyone out there knows anything about wiring up an Echo Can, and my outline below is incorrect, please let the me/list know.. I have posted the Documents I received from Tellabs at:

>> I'd have to agree with the channel bank plan. You don't even need to >> buy a used channel bank. You can get a new Rhino for $1500: >> >> http://www.channelbanks.com/ > > I gather you've had experience with Rhino. > > How does it work with Asterisk? > Does it provide all features? Caller-id, echo cancellation, how's the > voice

Hello, I am connecting Asterisk to an Adit 600 via a T100P. Unfortunately I am not able to get any lights on the T100P and the Adit 600 only shows red. I have already modprobed the t100p. Has anyone successfully connected these before? I've tried both a cross-over cable and a standard cat 5 cable, but I can't seem to get them to work. Any suggestions? Thanks! Craig

Hello, We have a high volume of incoming and outgoing calls that come in via our analog POTS lines connected to FXO cards in an Adtran TA750. This is connected to a T100P. We are using Polycom IP 500's. The problem we are experiencing is, on frequent occasions, when someone dials out, there is another person who has just dialed in. I have had this problem at my house before (without an *

Hi, Maybe someone has seen this before... I've installed a new T100P, but it doesn't seem to work. I've attached the T100P to an Adtran 750 using a crossover cable. The Adtran shows a red alarm on the T1 interface. The Adtran has been set to factory defaults with FXS cards in 1-3 and an FXO card in 5. The T100P shows no signs of life--the leds are not lit. Should I be seeing

Hello all, I've got a T100P connected to an Adtran TA750 with a T1 crossover... This connects to a patch panel with phone ports. The Adtran is fully populated with FXS cards. All I get on any phone port is a fast clicking noise... No dialtone. Asterisk 'sees' the card, (the channels show up in /proc/zaptel). Incoming calls are routed to the zap/x channel, but no ring. I'm

Hello, We have 15 Soundpoint IP 500 phones and recently call quality has deteriorated. On some calls there is a static-buzzing of sorts that occurs when users talk. It can be picked up on SIP-SIP calls and SIP-ZAPTEL (Channel BANK<<-T100P). It basically sounds really weird whenever someone talks, it sounds like a bee buzzing or something. Very hard to explain. Also, there will be echo

Hello, I new to this, but with the help of mailing lists archives and IRC I am able to build my PBX. Thanks to all who had help me to reach till here. I am stuck at a point where I can't find the solution on mailing lists or even on IRC. I have individual 4 DID (Direct Inward Line) coming from Telco and terminating into TA 750 to FXS card. Many of them told that Phone instrument terminates

Hello, I don't have any experience with channel banks and would appreciate any feedback on my theory outlined below: We have a single T1 entering the building with channels 1-12 being voice lines and 13-24 being a 768k internet connection. This T1 terminates to an Adit 600 (T1-1). Here's what I know. Channels 11-12 go out the Adit 600's 25-pair connector to a wiring block (and

Hello, I have just received Adtran TSU 600 with 24 FXS ports. I have installed sucessfuly T100P card. Adtran is connected to t100p with crossover T1 cable. On T100P card I have a green light and on Adtran I do not get any errors or alarms. But I do not get dialtone on FXS ports. Adtran is configured: For Network Timing, fxs ports ore fxs_ls on Adtran. In zaptel.conf: span=1,1,0,esf,b8zs

I've put a t100p in our * server and I'm having trouble configuring it. It is directly connected to an Adtran TA 750 channel bank with two FXO cards (8 analog incoming lines total). I'm able to insmod and modprobe both zaptel and wct1xxp with no trouble, but when I start * with /usb/sbin/asterisk -c I get the following output: [root@rosella root]# /usr/sbin/asterisk -c Asterisk

Jay, I have had a lot of trouble with the FXO ports on Adtran TA750. Unless the incoming POTS lines have a balance impedance, they will buzz very bad. Gregory P. Scasny Golden Technologies Inc. http://www.golden-tech.com 219-462-7200 -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Jay Milk Sent: Sunday, April

Hello, We keep having a really bad static problem on phone calls completed using a Adtran TA750 and T100P card. The phones are Polycom IP 500 phones and, it occurs across all phones. Not just one. Everything appears to be on it's own interrupt. I noticed the last time we did this, we rewired everything to make sure it wasn't an electrical issue. Well about a month and a half later

I have following setup Asterisk - T100P -> Adtran TSU600 P + FXOcard -> PSTN line When PSTN line is plugged directly in to analog X100P caller id is received by Asterisk but when I plug it into adtran I'm not getting caller id. Any ideas what kind of setup Adtran TSU600 requires to pass caller id to T100P ??? regards m.

I'm looking to buy a channel bank. I'll be using this to basically dual a Toshiba PBX and Asterisk so that we can deploy Asterisk in small steps and have the Toshiba as a fallback in case something goes wrong. What I need is a channel bank that will allow me to take in 12 lines using the FXO ports in the CB and then output those lines to the Digium T100P. Has anyone had experience

Hello, Has anyone else ever experienced Static Problems with a T100P connected to an Adtran Total Access 750? We have two FXO modules in the Chasis to interface to Verizon. At first I thought it was just one line, and was Verizon's fault, but now we are seeing it across all lines and it comes and goes. It's sort of weird, because only we can hear the static most of the time. The

As a follow-up to my previous post where I stated the IAD would be a Vina model, after some more prodding to XO, they have told me it will either be an Adtran TA-600 or a CAC Adit 600. These products are covered pretty well on the web and I have manuals on both. So, if those knowledgeable folks had to use one of these to attach to an Asterisk box, what interface would be best or at least