similar to: ATA-186 pass-through Flash

I'm getting some warnings: NOTICE[xxx]: File rtp.c, Line 264 (process_rfc3389): RFC3389 support incomplete. Turn off on client if possible Asterisk Version: CVS-01/06/04-13:50:26 Cisco ATA 186 version: v3.0.0 atasip (Build 031210A) Is this something I should be concerned about? Anyone know how to "turn off" the RFC3389 support on the ata 186? Thanks!

Calling from a Cisco FXO port to an ATA-186 (SIP 3.1 image) via * (either CVS-HEAD-06/28/04-11:43:41 or CVS-HEAD-07/12/04-15:49:58) I didn't hear any ringing sound & get the following on the console: -- Called 5503 -- SIP/5503-f6b5 is ringing WARNING[-1323201616]: channel.c:1375 ast_indicate: Unable to handle indication 3 for 'SIP/10.10.2.250-9903' -- SIP/5503-f6b5 answered

I have a ATA 186 with SIP firmware 3.1 when I changed the configurations to use the g.726 codec I received many erros and the calls doesn't work. I changed the fields: - LBRCodec: 6 <- the code for g.726 - TXCodec: 6 - RxCodec: 6 The errors: Jul 9 13:15:37 NOTICE[1192491824]: rtp.c:500 ast_rtp_read: Unable to calculate samples for format G726 Jul 9 13:15:37 NOTICE[1192491824]:

I am getting (with older image): RFC3389 support incomplete. Turn off on client if possible How do I turn that off for the DG104s? Or if I can't how do I tweak asterisk? I see posts about ATA-186's having an audiomode, but the closet I came to was inbanddtmf. I tried =0 and =1, no effect. Thanks! -- Zot O'Connor <zot@zotconsulting.com> White Knight Hackers, Inc.

Hi.. I just wondering why DTMF are not recognized by aterisk on incoming calls from my SIP provider ... ANy suggesteions ?` /Mike

When I make a call using sip, I get the line NOTICE[327696]: File rtp.c, Line 292 (ast_rtp_read): Unknown RTP codec 19 received Repeated many times on the console ; SIP Configuration for Asterisk ; [general] port = 5060 ; Port to bind to ;bindaddr = 0.0.0.0 ; Address to bind to context = outgoing ; Default for incoming calls allow=gsm allow=ulaw

I installed * to primarily test its voicemail feature. I installed it on a server WITHOUT any telco board (i.e., digium). Installation looks ok, however I am having problems. MY SETUP: 2xATAs are configured to use * as GkorProxy Asterisk is registered to my SER SIP/RTP Proxy 1.) First test - ATA1 calls to ATA2. When voicemail starts playing, it just cuts-off after 5-10seconds (consistently).

I'm having a horrible experience getting a Cisco ATA-186 to work with *. I can make calls from the ATA with no problems. However, incoming calls make the ATA ring once, and then the call is disconnected. I have no problems with my Sipura 2000 or my Grandstream phones. I am running 2.16.1 sip code on the ATA 186. Neither * nor the ATA is behind a NAT. They are both on public IP addresses

Are there any other codecs that can be used with the 7960 and the ATA-186? I have been using the default gsm codec and wanted to see if I could make use of something a little less bandwidth intensive. Kim Callis -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20030723/34e950e0/attachment.htm

Hi, Is there is some form of VAD on * for SIP channels, cause I have a problem with MOH. I made an extension which simply plays MOH, when I dial that extension with my ATA188 MOH sounds choppy if I talk on the phone the MOH keeps playing. I saw the sip channel (show channel SIP/*) and I see no packets going in/out when I talk then packets shows going in/out. I don?t have this kind of problem

Is it just me or do others have a problem with the ATA-186 de-registering? Every couple of hours, if I don't make use of the ATA connected line, I find that I have to unplug and let the ATA reboot. After that it is good to go for awhile, but eventually I have to repeat the process. My ATA sits behind a NATd firewall, any ideas what might cause the de-registration? Kim C. Callis

When I try to connect to * using a Cisco ATA 188 configured with a MGPC firmware (v3.1.1), I just keep getting this message every 30 seconds or so : May 10 10:08:21 NOTICE[7913]: chan_mgcp.c:1509 find_subchannel: Gateway '192.168.1.27' (and thus its endpoint '*') does not exist Using tcpdump, I have checked that the ATA188 (with IP 192.168.1.27 and port 2427) sends UDP packets to

I really should be doing something better on this beautiful weekend, but I'm trying to save myself some time for later projects by documenting some things that have been particularly troublesome in the past. That being said... I've written up a configuration guide for the Cisco ATA-186, which describes some of the features that are possible to set in the ATA and specifically what

I am trying to set up the Message Waiting Indicator (stutter tone/light) so that my cisco ata-186 will let my phones know there is a message waiting. However this does not seem to be very well documented. I found this on wiki mailboxnumber@context ... where does that go? Do I put it in my SIP.conf definition for my cisco ata, or where. In my SIP cisco definition i already have a

Hi - I need to configure Asterisk (Trixbox 2.2) and my ATA-186 with both ports. I need to be able to call one port from the other-- the idea is to have two phones in two different locations that _can_ call each other. So, in reading the Asterisk Wiki and other sites, the best documentation I found was this: http://www.loligo.com/asterisk/Cisco/ATA-186-guide.v20030628.txt

I see that there's now a 2.16.1 upgrade path for Cisco ATA-186 devices, dated (variously) July 11 or July 14 2003. Here are some interesting bugs that claim to be fixed. Most notable is CSCeb17953, at least from my perspective, as I've hit this bug before. CSCea42480 The Cisco ATA ignores the Require:100rel header and processes call. CSCea69889 The Cisco ATA builds a 302 Moved

For anyone who is interested, I have a working tftpd (modified wvtftpd) capable of serving configuration, dialplans, and ringtones to Cisco 7960/7940 and ATA-186 devices that are located behind NAT firewalls. As TFTP is not a very firewall/NAT friendly protocol, I had to break some rules to get it to work with these cisco devices. It might cause problems for other TFTP clients, but it works with

Hello list, i am using: asterisk CVS-10/13/03-11:54:33 chan_capi-0.3.0 ATA-186 V2.16.1.ms over MGCP Situation: ISDN calls ATA ISDN speaks with ATA ATA-Phone presses Flash and speaks to another one (SIP/snom200) ATA-Phone hangs up ISDN talks to SIP/snom200 snom200 hangs up The incoming extension of ATA keeps busy for a time (20 sec?), even its not off-hook anymore! Any ideas? -- Swapping

I want to setup an Asterisk network using the Cisco ATA 186. What is the best place to order those devices? I'm not finding them anywhere. Al __________________________________ Do you Yahoo!? Protect your identity with Yahoo! Mail AddressGuard http://antispam.yahoo.com/whatsnewfree

In the process of investigating a Cisco ATA 186 that was locked by Vonage, I found that you can still unlock the device yourself. But there's a catch. The device's design has a great plus: a DIP32 *socketed* SST28SF040A flash chip. I found an 8 digit unlock code at 0x03FA71-0x03FA78. I do not know if that is a standard location. If you have the equipment, you're in luck. But