similar to: automatic voice dialout call

Hi all, I was unable to obtained a smoothed line using the loess function. I used the following code reported in the examples of R documentation: cars.lo <- loess(dist ~ speed, cars) Then I tried to plot both the data and the smoothed line plot(cars) lines(cars.lo) but what I obtained is simply a broken line joining all the data points. I tried with different spans, but the results did not

Dear all, when I try to install gtkDevice on Mandrake Linux 9.1 (R v. 1.7.1), I get the following comfiguration error (see below). Has anyone else had this problem? Any hints are greatly appreciated. Thank you in advance, Dimitri install.packages("gtkDevice") trying URL `http://cran.r-project.org/src/contrib/PACKAGES' Content type `text/plain; charset=iso-8859-1' length

Hi! I want to use Asterisk as load generator to test quality degradation with increased load (e.g. testing other SIP equipment or IP-links). Is anybody aware of such a setup with Asterisk - is it possible to get RTP statistics out of Asterisk (e.g. jitter, packet loss, reordering ...)? Thanks Klaus

Hi, I'm trying to get asterisk to auto-dail out. I created a *.call file with the the top of it being "Channel: Zap/1/2609944", which should have connected to Zap channel 1 and dial out to 2609944, but It did not do so, asterisk would say a call was completed to Zap/1/2609944 but I never heard that phone ring. So I tried just putting "Channel: Zap/1" at the top of

If you set "dialout=fromvm" in your voicemail.conf, how do you then go about being able to dial back out? Is there a service feature code?

I've been reading the Linejack strikes again messages, and have another Newbie question is it possible to use a Voip Product as a Dialout line for * ? I have a Vegastream 100 Voip to PRI. box. With * can I use that as a Dialout / dialin box? The Vega100 does either sip or h.323. Thanks. Bradley Greep

Hi, I am having some trouble with ISDN Dialout. Using a Netjet-s PCI Card. When in Minicom, the only way I can dialout is if i issue ATS18=1 First. Otherwise I get a BUSY message. So thats fine. But when I dialout from asterisk, I get an immediate hangup, so my guess is that asterisk is not issuing ATS18=1 to the ttyI device. Here are my configs, any input would be greatly appriciated.

Hello All. I am trying to use RAGI the ruby agi framework with trixbox. I am having a problem with the dialout part. The RAGI framework creates a file in the /var/spool/asterisk/outgoing directory and routes the call to an extension (I have listed the relevent portion of the file below). The problem is that the initial dial command does not execute properly in trixbox. I am hoping somebody who

I am trying to find a way to allow dialout from voicemail when connected from an 'internal' extension context, but prevent dialout when connected from an 'external' extension context. As far as I can tell the dialout context that can be set in voicemail has no regard for the context from which the call to voicemail came in. Any ideas on this? Maybe a variable passed when

Hi! I have an automated dialout via a call file to a mobile. Can I detect when the call is not answered but forwarded to the mobile operator voicebox? I would like to stop the dialout if this is the case. TIA, Mike

Hi, When I try to dialout over chan_capi everything works fine when I settle for msn=* in my capi.conf and use the primary msn of my ISDN-line. But trying to configure a different MSN the chan_capi doesn't dial and comes with: No one is available to answer at this time What can be the prob? -- Thanks, Marc aka IzNoGood

Dear all I read on the list back in 2003 that * does not support IXJ LineJACK dialout yet is this still the case? Thanks

Hello my name is Ilija Poznic and I have a problem. My configuration is 1. Digium TDM4000P with one FXS. 2. AVM Fritz ISDN adapter (configured with capi). When I connect to my ISP and then start *. Asterisks is registering me to SIP provider iconnect. After that I can call international call trough VoIP. My problem is that I want to dialout to ISP only when I have a international call.

I previously posted about this problem and received suggestions involving turning off echo cancellation. As far as I can tell, echo cancellation is already disabled on this channel, so I'm back. What I've got is a small home setup with a single four-port Digium card: Module 0: Installed -- AUTO FXS/DPO Module 1: Installed -- AUTO FXS/DPO Module 2: Installed -- AUTO FXS/DPO Module 3:

Hello! How can one select outgoing MSN when dialing out from ttyI-interfaces? I have successfully done this with CAPI e.g... exten => _XXXXX.,2,Dial,CAPI/60:bBYEXTENSION ...in extensions.conf. Currently correponding for my ISDN modem interface is... exten => _XXXXX.,2,Dial(Modem/g1:${EXTEN}) ...but this selects only MSN of outgoing group g1 for dialout MSN number. I also tried to

Specs FC2, Asterisk 1.0.0, Zaptel 1.0.0 TDM400P Port 1 FXS Port 4 FXO Standard analogue handset plugged in with pstn line. Problem: When I go to dialout it drops numbers on the outgoing number. Keys dialed from handset were 9 0418800185 I tried hitting the keys slowly as well as at my normal speed, all tones are heard in the handset for all numbers.

Hello asterisk-users. I have the following dial-plan: [test] exten => 482,1,Dial(OH323/106@192.168.2.73,10) exten => 482,n,Dial(OH323/102@192.168.2.73,10) exten => 482,n,Dial(OH323/103@192.168.2.73,10) exten => 482,n,Dial(OH323/104@192.168.2.73,10) exten => 482,n,Dial(OH323/105@192.168.2.73,10) exten => 482,n,Dial(OH323/106@192.168.2.73,10) When I call exten =>

Hello all. I am trying to dialout via a provider here in japan that doesn't accept the username:password@host.com/number format. However, when I use X-lite I can still call out. Are there any other fields that can be used instead of the "/number" to indicate the target number? Hope this is clear enough :-( Jason

Hello! I'm using Asterisk 1.4 with Dialogic Diva Server Analog 8P (with CAPI) and I need to find a way (it can be tricky) to get the DIAL STATUS of the call when I use the auto dialout queue. I know the DIALSTATUS variable can only be used with Dial application, but I have to make difference between a busy line or a not answered call. Any clue? Thank you very much. regards, -- SOILEN

Hello, I am new to Asterisk, so RTFM answers welcome too (just include the FM's link :). I'd like to build a simple dialout server based on Asterisk. I installed 0.4.0 from package (a Debian SID machine, "server"). The client is gnophone (a Debian SID machine too, "client"). My modem is a GVC 56k voice modem connected to the server's serial port. I modified