similar to: Chan_h323 & gnugk

Jeremy, In some posting in the mailing lists, you mentioned that docs for h323 had been submitted but hadn't made it into distribution. Could you post those docs in your download directory? I'm trying to understand the nuances of your driver, gnugk, and extensions. Ray Burkholder ray@oneunified.net http://www.oneunified.net 704 576 5101 -- Scanned for viruses and dangerous content

Hi, I'm using asterisk with chan_h323 together with gnugk. chan_h323 and gnugk were recently compiled with pwlib-1.5.2 and openh323-1.12.2 as advised. When connecting asterisk directly by ohphone (without gatekeeper), everthing is fine. When using gnugk for usage control in routed mode, I find a funny situation in asterisk's H.323 debug: == New H.323 Connection created. --

I'm trying to configure Chan_H323 to register with GnuGK... without success... i've failed finding sample configurations. I'd greatly appreciate anyone who can provide sample config of H323.conf and gnugk.ini I am tyring to configure Asterisk as a neighbor in GnuGK. I'm always getting this error on Asterisk. ERROR[16384]: chan_h323.c:1987 load_module: Gatekeeper registration

What types of ISDN BRI cards work well in Europe (Guadeloupe, Martinique and France) ? For example: AVM C2 or AVM C4 or eicon Diva server 4 BRI? Any others? Which driver is appropriate? Ray Burkholder ray@oneunified.net http://www.oneunified.net 704 576 5101 -- Scanned for viruses and dangerous content at http://www.oneunified.net and is believed to be clean. -------------- next part

Current setup: Polycom IP3000 <-> gnugk <-> asterisk <-> Cisco 7940 Asterisk and gnugk are on 10.20.98.6 IP3000 is H.323, using G.711 (10.20.98.2) 7940 is SIP, using g711ulaw (10.20.98.3) I've been asterisk for a while now, only using SIP devices. I'm happy with that side of things, but I've not used H.323 before this week, in trying to get the IP3000 to work. *

Hi, I have the following topology: PSTN/H323 gateway->GNUGK->chan_h323/chan_sip->SIP EP Mostly everything works fine except chan_h323 is not passing audio from PSTN before the call is answered and as a result users can't hear PSTN announcements (like "the number is not in service") that's played on unanswered call. All they hear is just continuous ringtone as though

I have a few 7960 Skinny phones. I've edited the skinny.conf file, but I'm a little unsure as to how get the phone to figure out which ip address it should register with when it boots. How do I do that? I already have a tftp server for my SIP based phones. Do I need a tftp server for skinny configs at all? And if so, can it be the same tftp server as the SIP ones use (I'm not sure

Hi, I also had some problems using chan_oh323 together with gnugk. * <-> gnugk <-> h323-phone When I called the phone and hang up, befor the phone was picked up, the h323-phone continued ringing. The same, when the h323- and some sip-phones were called, and the sip-phone picked up the call first. (It is annoying, when you are talking to someone at the phone and the phone on the

Hello, I installed Asterisk from CVS on Redhat Linux 9 and working with chan_h323 module and g729/g723 free codecs too. My network connection diagram: ---------------------------------------------- X-lite/X-Pro-->Asterisk--chan_h323-->GnuGK--->AS5300-->PSTN boldsoft*CLI> show version Asterisk CVS-v1-0-03/24/06-15:27:08 built by root@boldsoft on a i686 running Linux I can make

Greetings- As most of you who monitor this list know, I've been messing about with Asterisk -HEAD, Cisco Callmanager, and the nufone H323 channel driver here for some time- with pretty decent success. I'm hoping to cash in a chip here- I've run into something that is probably a very simple answer, yet not found a decent reference to resolve it. Scenario- -HEAD as of last week

> The documentation mentions that the Digium channels can be split into some > voice channels and the remainder of the channels used for routing IP > traffic. > > Does any one have this in use in conjunction with Asterisk? Does it work > well? Would you recommend it for a production server? > > Obviously, if this works, this makes for a cost effective platform where

Hi! I'm trying to build gnugk with asterisk. Asterisk is working well with chan_h323 built with needed PWlib v.1.5.2 and open H.323 v.1.12.2. But gnugk' s installing instructions says that I need latest PWlib(1.17.1) and openh323 to get gnugk work. Now, with installed pwlib and openh323 gnugk's compiling fails and I get error 1. Do you have any working solutions with asterisk and

I have one and only one reason to use OH323, and that is it works with Cisco's CallManager. The standard H323 channel has one-way audio issues when connected to CCM and fixing them has been identified as a low priority/never going to happen task. Dan -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of

I am using Nu Fone Network's h323 drivers. I can place H323 calls using following in extensions.conf file, exten => _1732.,1,Dial(H323/${EXTEN}@192.168.1.2) If I need to use h323.conf to do the same I cannot configure h323 to do the same. I get everyone is busy message and I do not see IP packets being generated by * trying to communicate to 192.168.1.2. Can someone point out what I

Dear ALL: I find that everybody discuss with asterisk-oh323 instead of chan_h323 of asterisk channels. Why do they choose asterisk-oh323 and not use the build-in module (chan_h323)? What different between these two componments? In my guess, the build-in module should be easy to implement rather than setup another application(asterisk-oh323) expect some bugs or failed functions on chan_h323.

I'm trying to come up with an elegant solution to handle roaming users in a branch office scenario. I have a number of possible scenarios, none of which seem to completely solve the problem. Perhaps someone with a better feel of the interactions can help me out. Is the 'switch' statement useful in some way? What are the ins and outs of the 'switch' statement? Come to think

hi IIRC, Jeremy once said that chan_h323 could be used as a gatekeeper but perhaps lacking a few features as compared to gnugk. Is this possible? I have some dlink DPH-100H phoes here for testing, but they require a gatekeeper, and if I can do it, I'd love to keep gnugk out of this. thanks roy

Hello, I am trying to configure asterisk with GnuGK. Is it possible to configure Asterisk OH323, CHAN_H323 without register to GnuGK gatekeeper? thanks, Ganbold -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060118/5f99c433/attachment.htm

I'm having a problem with chan_h323 compiling for Asterisk. RedHat 7.3 PWLIB 1.4.11 pwlib_1.4.11.tar.gz OpenH323 1.11.7 openh323_1.11.7.tar.gz [asterisk@jonux h323]# make clean rm -f *.o *.so core.* [root@jonux h323]# make cc -g -pg -c -o chan_h323.o -pipe -Wall -fPIC -Wmissing-prototypes -Wmissing-declarations -DP_LINUX -D_REENTRANT -D_GNU_SOURCE -march=i686 -DPBYTE_ORDER=PLITTLE_ENDIAN

We needed the client browser to be open all the time for dynamic data to load without the page refreshing. After looking at all of our options we decided on programming it ourselves using flash rather than java. We have a flash frontend thats tied to our backend mysql DB. We use it for loading web site traffic data, email opens, click-throughs, bouncebacks, stats, etc. It could also be used with