similar to: "Starting simple switch"

Hi list, Sometimes I receive a Red Alarm in my E1 trunk (E&M immediate start signaling), and just few seconds after this, all alarms are cleared. This problem ocurrs many times/day, and if are calls in progress, these calls just hang-up. Could it be an asterisk bug? Or may I contact the PSTN provider? Thanks Eduardo

Hi, I'm abaut to install asterisk and I want to know if buying an E400P (Quad Span E-1 Interface) from digium my linux box will be ready (of course, after configure it) to work with PSTN and my already in use PBX (E1 interface), or I'll need to buy additional DSP's cards or whatever? thanks Eduardo Gon?alves AceNet do Brasil LTDA 55 11 3365-0500

Hi list, What paremeter can I change to control interdigit timing? Because my PSTN provider aren't receiving all the digits I dialed on Zap/g1. My Zap/g1 are an E1 (E400P) using E&M immediate sigalling. thanks in advance Eduardo

Hi, Digium's E400P has RJ45 conector and my E1 link has BNC concetor. Could someone tell me the cable pinouts to make this conection? thanks Eduardo

Hi, Can someone send me a sample on how to get an E400P working with ISDN PRI signaling? What conf. files must I edit? thanks in advance Eduardo

Hi friends, I'm testing a E400P with PRI signaling. When I start asterisk (-vvc), i get the fowlling messages in /var/log/asterisk/message: May 12 12:42:06 WARNING[1024]: File chan_iax2.c, Line 4931 (set_config): Ignoring port for now May 12 12:42:06 WARNING[1024]: File chan_zap.c, Line 6525 (load_module): Ignoring ocancel And 'show channels' returns no channels. Can anyone help

Greetings, According to the FAQ "When you load the module and have no circuit/channel bank the LED's should flash red" I get the "knight rider" lights before the module loads, but after the modules are loaded I don't get any lights, other equipment plugged in or not. The card has been on my shelf a while so I wonder if it needs a firmware upgrade ? Can the cards

Hi list, I have a asterisk box with an E400P that was running ok until last week. The machine just stop responding and after a reboot, the module (tor2) doesn't load anymore. anyone could help? regards Eduardo modprobe returns this: asterix:~# modprobe tor2 Zapata Telephony Interface Registered on major 196 Detected Tormenta 2 Quad T1/PRI or E1/PRA at 0xfe121800/0xfe121000 irq 7

Hello, Is there any configuration in zapata.conf for fax detection (or transmission)? When I try to send a fax trought asterisk, the line 'Fax Handled:' is always set to "no". The scenario is: [ata186]---sip---[asterisk]---e1 E&M---[pstn] Fax sometimes goes without problem and sometimes the fax machine can't send the fax. Thanks Eduardo

Hello, I have the fowling scenario: fxs[asterisk1]-----iax-----[asterisk2]e1----e&m---PSTN I want to know the steps to transmit fax from a machine connected to the fxs to a fax machine on the PSTN. The same for dial-up's. Is it possible only with a/ulaw ? What configs I need in asterisk1? Thanks in advance Eduardo

Hi, I have an ansterisk and a cisco 827-4v registered to a Gatekeeper. asterisk has two extensions: exten => 223,1,Dial,OH323/BYEXTENSION@827PD exten => 730,1,Dial(IAX/eduardo@10.0.11.103) (IAX are working well) When I try to call each other, gnugk shows a ARJ: ARJ|10.0.11.112:1720|223:dialedDigits|730:dialedDigits|false|resourceUnavailable I think this could be a codec

Hi list, I'm trying to set up a TDM40B, but modprobe returns the fowling errors: asterisk:~# modprobe wcfxs ZT_CHANCONFIG failed on channel 1: Invalid argument (22) /lib/modules/2.4.18/misc/wcfxs.o: post-install wcfxs failed /lib/modules/2.4.18/misc/wcfxs.o: insmod wcfxs failed Could someone give me a help? Thanks in advance Eduardo

Good day everyone, A Solution now exists for those of you still looking for the first model of Quad T1/E1 Interface Cards - the T400P and E400P. The T400P and E400P were manufactured by Digium until a few months ago, and were designed and released under the GNU Public License as the Tormenta II by Zapata Telephony. Varion, Inc. is now in full production manufacturing these boards. With the

Hi I wonder if you can help me. I'm currently studying Networking as a college course and one of the challenges we have been set is to research, then put into practice the mapping of a linux server onto a Windows NT server. I'll be honest with you, I'm very new to all this so I hope I explain this correctly. I have successfully created my own smb.conf file, usernames, areas and a

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi, I'm attempting to hook up the E400P card to a Siemens ISDN module. I have no knowledge of these Siemens products, so I'm acting on what I've been told about it. The Siemens side is configured to "ISDN30: ECMA QSIG". The Siemens manual states the card provides 30 ISDN B-channels which can be used for trunking or

dear list I use runif to generate a ramdom number between min and max runif(n, min=0, max=1) however , the syntaxe of rexp does not allow that rexp(n, rate = 1) and it generate a number with the corresponding rate. The question is: how to generate a number between min and max using rexp(). Regards -- PhD candidate in Computer Science Address 3 avenue lamine, cité ezzahra, Sousse 4000

Hi, I add a div to my document and use an effect to make it apear gracefully. Unfortunatly, when adding the element, the element apears shortly, then the effect (slideDown) lets it apear nicely - so the page flickers abit - What is the best practice to avoid it? Cheers, Ron

Maybe one of you can help me with this: We have T1's that come from both MCI and Global Crossing as uses channelized (24 Ports per T) with inband (DTMF) ANI and DNIS delivery (format = *DNIS*ANI*). My old equipment was set for D4, AMI, SF and Wink Start and so is Asterisk Server. I've moved these T's to Asterisk TE410P and inbound calls are arriving to external voice mail

Hi all, i have observed, that sometimes all BChannels on my Zaptel Pri device (E400P) will be restarted. The E400P is connected to another pri switch. In the traces from the other side (pri switch) i can see that libpri request for the channelid is 255. Is this a bug or a feature ...? Or, can it be a bug on the other side (terminator switch) ? Have anyone an idea ? Thanks, Thomas.

Hello, after some time monitoring my installation to see how its working, I found that some ramdom times, like one or two days in a week, the driver fails to start and upsmon keeps registering a "data stale" error on Windows' event log. I've set the NUT service to "delayed start" to see if it was a driver conflict on the system start rush, but it keeps doing it