similar to: WCFXO echo rexolved for me

> Brian> Hello, I resolved my echo issue using grandstream/estara > etc etc Brian> sip phones and wcfxo interfaces from digium. I > swapped out my Brian> via kt400 based msi kt4vl motherboard for an > asus p4pe? i845? Brian> based motherboard and the echo has > completly gone away along Brian> with aggressive suppressor option > in the makefile. I hope this

Like most others on this list I also have some really annoying echo whenever a call goes out to the PSTN from a SIP phone... SNOM/Budgettone -> Asterisk -> X100P -> PSTN I have tried every echo canceler in the makefile and turned on and off aggressive suppressor etc. etc. etc. tried 32,16,128, and 256 bridgetaps and I can get it reduced to only a few seconds on the intro of the call and

When booting Ubuntu 6.06.1 (Linux 2.6.15-27-386), wcfxo would load but not configure. I have three ways to manually force wcfxo to configure: 1) ztcfg, 2) modprobe -f wcfxo, or of course 3) unload and reload wcfxo. Each works equally well. As a workaround, now I have to put ztcfg in rc.local, which Debian doesn't favour. I had compiled the same zaptel under Ubuntu 5.02.0 on two

I have two X100P cards that were working just fine for months. When I run modprobe wcfxo today I got the following error: ZT_CHANCONFIG failed on channel 2: No such device or address (6) /lib/modules/2.4.19/misc/wcfxo.o: post-install wcfxo failed /lib/modules/2.4.19/misc/wcfxo.o: insmod wcfxo failed The output of dmesg said that wcfxo:Out of space to write register 06 with e0. What?s

Hi, We are looking at consolidating our lines with PRI. This will allow the elimination of many fax lines. Some of them will be replaced with this type of config ... PRI * IAX * Channel-Bank FAX We will have daggressor suppressor enabled. Is anyone doing this and should I expect smooth operation? John This e-mail was scanned and found clean by Monroe-Woodbury CSD Antivirus.

I found similar posts regarding this error but none that answered my question. My zaptel.conf reads: fxsks=1-2 fxoks=3 loadzone=us defaultzone=us and /proc/interrupts: CPU0 0: 5542402 IO-APIC-edge timer 1: 2 IO-APIC-edge keyboard 2: 0 XT-PIC cascade 8: 3 IO-APIC-edge rtc 14: 72582 IO-APIC-edge

I have a X100P and a TE110P in my Asterisk box. I can either get the X100P or the TE110P to work, but never both. Here's my zaptel.conf span=1,0,0,d4,ami e&m=1-24 fxsls=25 When I load wcte11xp and wcfxo, I will get this error. [root at asterix etc]# modprobe wcte11xp ZT_CHANCONFIG failed on channel 25: No such device or address (6) /lib/modules/2.4.20-8/misc/wcte11xp.o: post-install

Thanks in advance root@asterisk01:~# modprobe wcfxo /lib/modules/2.4.20/misc/wcfxo.o: init_module: No such device /lib/modules/2.4.20/misc/wcfxo.o: Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg /lib/modules/2.4.20/misc/wcfxo.o: insmod /lib/modules/2.4.20/misc/wcfxo.o

Hello everybody, After going through multiple posts on Internet and trying different things I can't seems get zaptel wcfxo loaded on the server correctly. I run dual P3 500 Mhz box. After reading README.udev I put a file 60-zaptel.rules /etc/udev/rules.d # Section for zaptel device KERNEL="zapctl", NAME="zap/ctl" KERNEL="zaptimer",

Can I have a TDM400 and a T100P in the same machine? I am using AAH and trying to combine two boxes. If so, can anyone tell me the proper config for zaptel.conf and zapata.conf? Thanks! Wiley -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20051006/061d9d84/attachment.htm

Hello, I have found a "bug", I think in the way TDM400P cards handle FXO interface disconnect/re-connect problems. Normally I do keep all the wires connected from my CO / PABX quite securely, but I had a need to re-route the cable from one side of the desk to another, and I simply disconnected the RJ-45 connector and plugged it back in. THIS PROMPTLY RESULTED IN VERY VERY SCRATCHY AUDIO

Hi all I ahve been having problems loading the wcfss and wcfxo drivers I get an error message invalid argument and something about post install insmod failed the currently load modules do show the drivers loaded but asteris won't start lsmod root@slackware:~# lsmod Module Size Used by Not tainted soundcore 3332 0 (autoclean) wcfxo

I'm afraid that I am at a loss here. I am new to Asterisk, and have successfully set up SIP. But I cannot get my FXS card working, and I'm not sure what else I can try. # modprobe wcfxo /lib/modules/2.4.21-37.0.1.ELsmp/misc/wcfxo.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may

Hi, Im getting mad with this error, I have a x100p installed with wcfxo module loaded perfectly, I can receive incoming calls and detect very good the hangup for incoming calls. But for outgoing calls its a mess. When I place a call for outgoing, i heard the ringing, my cell or phone rings and when I pick up the phone it hangs: -- Called g1/91xxxxxxx -- Hungup

Hi , I picked up a x100p the other day and thaught I'd havea go at getting the driver going for linux 2.6, things have gone pretty, two basic problems. 1. makefiles, with 2.6 you can't get away with using the old makefile to build the kernel modules, they will build but you'll get an error along the lines of "no module found in object". This is due to not using the new

Hi all, I installed the estara softphone and had no problem registering it with asterisk. I could make calls to other hardware SIP phones (Cisco 7960) from the softphone, but I couldn't call the softphone from the Cisco 7960s. The asterisk console gave me an error message saying "unable to create channel" to my softphone. What could be the problem? I searched the archive with no

I've made some modifications to zttest in order to use it as a frame clock accuracy tester / slip detector. I'm not certain if that was it's original purpose, but it seems that a lot of folks try to use it that way. The result is something that I'm calling ztclock for now to help avoid confusion. I'm including the source at the end of this post. You can compile it by placing

Hello people. I would like to know if someone knows about any applet to include in a web page to start calls. What I am looking for is something that doesn't allow users to change numbers, or any other option, so I can include it in my web page and force them to call to me and no one else. I have tried JIAXClient, but it allows people to call anywhere, and what I want is just a configurable

What is the current status of the residual echo suppressor in the preprocessor? I ask this because I have occasional problems with the AEC, in which it fails to cancel echo. I think the problems have to do with samples being dropped by the audio IO system, which is effectively impossible to detect and counteract reliably. A colleague recommended using an echo suppression technique (which he

Believe me; I've "played with" priorities and buffering. Did you just say you have no idea how the Speex residual echo suppressor works? If that is the case, can you tell me where I could get some information about it? -----Original Message----- From: Jean-Marc Valin [mailto:jean-marc.valin@usherbrooke.ca] Sent: Friday, June 29, 2007 7:38 PM To: Coffey, Michael Cc: