similar to: Problem with Dutch PSTN-line on X100P

Hey all, I recently noticed that DTMF caller-ID was implemented in CVS, so I requested the service from my telco (the Dutch KPN) and tried to get it going in Asterisk (current CVS), without success so far. This system has 1 X100P, 2 TDM400P's with 4 FXS-modules each and 2 HFC-PCI ISDN-cards (zaphfc-driver) in it. The analog line I'm trying to get caller-ID working on is obviously on the

Hi all! I am in the same situation here in Sweden, but I just got the X100 card and don t get it to work with DTMF caller ID. Is the only way to solve this to buy a TDM400 card w FXO modules? Is it just a driver question or a HW issue with the X100 card? Where to find dok about the new keywords in conf files like "cidstart=polarity" in zapata.conf? rgds Gunnar >>>

Yo all, The PSTN access-number for the Dutch IAXTel <-> PSTN-gateway has changed. The new number is: +31 20 3987 567. Calling from IAXTel to Dutch toll-free PSTN-numbers is still done in the same way, by calling "31800<rest of number>". Mark: Could you please update your web-sites to reflect this change? The old number is mentioned on "http://www.gnophone.com/",

Has anyone seen this problem before? I have a server with a single X100P card. The audio level is a low, but if I raise the gain to more than -2db (Rx + Tx) it starts to oscillate in an echo test. Not at a high frequency but with a noise that is best described as a steam engine starting up. It then starts to clip and crackle. If I bring the gain down to Rx=-2.0 and Tx=0.0 or lower then it settles

Hi all, I'm having a problem with * being very finicky about the length of DTMF key-presses during menus, voicemail, etc. Basically, short (<100 ms) tones are ignored, anything between 100ms (or so) and about 300ms is correctly detected, and anything >300ms is interpreted as multiple presses of the same key. This is terrible for callers who are trying to get to the correct

Hi list, Hopefully, some of our Dutch members can help with this one. I'm also based in the Netherlands and am using a Sipura (Linksys) SPA-3000 (firmware v3.1.10(GWd)) as a PSTN to VoIP gateway for my Asterisk test system. It works fine, except that the Called ID (CID) is not working. I'm aware that KPN (our local telco) requires a separate subscription to activate CID on POTS

Hi list, I have a server running a simple hfs isdn card running with chan_misdn. the problem is, I can't get asterisk to pick up the phone, outgoing calls work fine. when running asterisk with -vvvvvvvvvvvc I get the following "log" when I try to dial the isdn server. P[ 1] * Starting Ast ctx:kpn-in dad:0594643637 oad:0878722291 with 's' extension P[ 1] MGMT: SSTATUS:

Here is my system: POWER SUPPLY 450W ALLIED ATX450P4 R(41) MB NFORCE2 A7N8X DELUXE ASUS RTL(Standard) CPU AMD|2500/333 ATHLON XP BARTON R(Standard) DDRAM 256M|DDR333 PC-2700 -K %(Standard) HD 40GB|WD 7200RPM 8MB WD400JB%(70) VGA ASUS|V8170MAGICII/T 64M MX440SE(58) CD ROM 56X|AOPEN CD-956 RTL(22) Besides the above parts, i have 2 X100P FXO PCI cards, and 1 TDM40B I bought 2 phones from radio

Hi to all, I have a question about the callerid (msn number) off calls comming FROM a queue. This is my setup: - ISDN using zap (zaphfc) - Incomming calls arrive in a queue - One of the members of the queue is my cell phone... member => Zap/g1/XXX73XX19 (X to protect my privacy ;-)) The problem is the call from the queue to my cell phone. In a dailplan i can set the outgoing msn using

I have a problem with Asterisk-bristuffed using a zaphfc card. I am located in the Netherlands, so I have an ISDN line from KPN. When I start Asterisk, and plug in the ISDN line, everything works perfectly for about 5 minutes. And then the ISDN line is down for 1 minute, and after that minute, the line comes back up and works for another 5 minutes. Every time the line goes down I get the error

Can anybody recommend a reseller in Europe (Netherlands) for modules for the X100P (FXO and FXS modules)? Cost, support are important. Also, what is a reasonable price for an X100P in Europe? Is there a difference in price between OEM and Boxed versions? Thanks, Pieter

I've read and experienced the echo problems with the X100P. Is Digium going to fix the problem or refund our money? I want to see this work because myself and other small companies out there use analog lines. I would trade up to T1 but that requires me to have at least 9 lines. If I did trade up, do the T1 cards work perfectly with no echo at all? I get echo with my directly connected

Hi, I suspected that I the analogue phone should have got a pass through signal when the power was off to the server, unfortunately it doesn't. I kept asking digium support about that but they didn't give me an answer. The problem is how do I identify whether the X100P is incompatibel with the network or faulty without possibly wasting another USD100??? Aaron On Sat, 2004-05-15, Eric

Hi, Has anyone got the X100P to work with an anlogue line in the Republic of Ireland? I have the X100P installed but zttool indicates a Red Alarm status on the card. It is on its own interrupt and I have tried different PCI slots but all to no avail. Are there any alternatives to the X100P that can work with asterisk and are likely to work in Ireland? Thanks, Aaron

Hi all, Which is the practical (from your experience) limit of the number of X100P cards installed in a single Asterisk box? Asterisk can work reliable with 6 X100P cards in the same box? Anyone know when the 4 ports FXO Digium card will be available on the market? Many thanks, Dan P.S. Please do not aswer with RTFG ...tried before without success...:-))

Hello, I would like to put 1 asterisk box in Country A and 1 asterisk box in Country B. Let's assume : - Asterisk box in country A = GWA - Asterisk box in country B = GWB - Calling party number (located in country A) = CgPNA - Called party number (located in country B) = CdPNB - Second Called party number (located in country B) = sCdPNB - PSTN in country A = PSTNA - PSTN in country B = PSTNB

We are running asterisk with a single POTS line for local calls and a voip line for long distance. Whenever we receive a call on the POTS line it is more than likely, but not always, going to have significant distracting echo. In addition to that there is occasional heavy crackle or static. I have tried to follow the guidelines at :

Hello all, Recently I purchased an QuadBRI card from junghanns.net after some playing around, reconfiguring dialplans etc with the exception of 1 thing everything seems to work: I seem to be unable to set the outbound callerid. The dutch telecom operator (KPN) provided me with 4 MSN's on 1 BRI interface. In the past years I'm more then used to setting the MSN without the leading 0, this

Hi. I have installed a x100p (THE x100p for those who have seen my former post). Now I just want to connect a "normal" phone (not an IP phone) to the card and use it as a sip extension (I have a FWD account)... more clearly: I want to be able to pick up the phone and call any FWD user using my FWD account... receive the FWD calls in that phone, and also to be able to make normal

I was told the X100P will have issues if installed on a line with a DSL connection. Is there a card that will work correctly on a DSL connection? Thanks!! -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040504/6de6226b/attachment.htm