similar to: TDM400P??

Hello, everyone After having spent several time to look for any solution for my problem, I decided to write here. Here is the problem got a Digium X101 FXO card and Digium TDM400P alias freshmaker (1 fxs module on it on first port ) in my asterisk box. The X101 works perfectly. The problem comes from the TDM400, when i plug a tested working phone on it , i get no dialtone; the goal is to

I installed the TDM400P and installed it on a system running on Fedora Core1, please refer to the steps below. I connected an analogue phone to the FXS port. When I pick up the speaker I don't hear the dialtone although when I press a number key I hear a DTMF generated. What could be the problem? I appreciate your help 1- First I installed the TDM400P in the PCI slot and connected

Hello all, I just installed a TDM400P with 2 FXO modules on my asterisk server. The card works perfectly. To get users to ring out from my SIP phones i setup an extension with 0 that basically does something like this: extension => 0,1,Dial(ZAP/g1) where g1 is the group of the two FXO channels extension => 0,2,Hangup This works exactly as i want so users basically can dial 0, wait for

Hi, I have just built my home Asterisk box into a better PC that became available (still only a P2 350 but it only has to manage 1 analog line).. Anyway I have built it on Fedora Core 1.. I have an X100P and a TDM400P (1 module installed).. These cards were working fine in my older PC that was running my Asterisk at home.. The inbound calls via the X100P to my sip phones are working great..

Hi, We have two of these 4 port FXO cards. However, we are having some problems with incoming/outgoing calls. The latest version of Asterisk/zaptel from CVS is being used. Voicemail, internal SIP <-> SIP calls between Pingtel xpressa hard phones work terrific, echotest is fine, and so on. The zaptel and wcfxs modules load fine, and show all 8 FXO interfaces in dmesg:

I apparently have a dead FXS module. Is there any kind of test I can run on it (on a live system) to determine if its good or bad? The telephone has no dialtone, gets no calls. It has been working for several months, and just quit yesterday. Thanks! Found a Wildcard TDM: Wildcard TDM400P REV I (4 modules) Freshmaker version: 73 Freshmaker passed register test Module 0: Installed -- AUTO

Yo all, I have a problem with a Dutch (KPN) PSTN-line, connected to an X100P. The call wil sound OK at first, but after 10-20 minutes, the audio will start to crackle. Soon after that, this crackle turns into a continuous noise and the parties won't be able to hear eachother anymore. It also sometimes happens that the party on the TDM400P hears a very loud, short-delay echo of themselves,

Since the irc channel wasn't any help, I will try posting my problem here. I have two TDM400Ps less than a week old in a PC. All of the FXS ports work fine, and all of the FXO ports worked fine up until thisafternoon. If I try to dial in, I get a busy signal, if I try to dial out, all I hear is a very scratchy, very crackly dialtone. If I swap the first FXO module with the second on the card,

HI Asterisk Gurus I'm connecting my * server to a zplex 10B, I'm using a slot on my TE410P card as T1 to connect my server to the channel bank (i use a cross cable), the zplex doesn't show any alarm neither the server. I'm trying to make calls from (ext 1) from the channel bank, to other (ext 2) in the same channel bank, but when I dial the ext number, the dialtone doesn't

Hopefully someone here can save my sanity. I have been trying to solve this problem for days now, but just cant put my finger on it. Im new to * so I have probably done something stupid! I have a TDM400P with one FXO module and a FXS module. The main problem I have is not being able to get the extension attached to the FXS module to ring or be able to make calls. It gets a dialtone fine but I

We have a S100U which we were using as our sole internal phone extension. Today it died. Picking up the phone now results in a brief dialtone followed by bursts of random static and crackling noises and then a second or two of fast-busy followed by silence and more crackling noises. I've tried the hardware attached to a couple of different machines as well as a couple of different phones.

We have a TDM400P installed here with four FXS modules. It works well except for a couple of issues: First, I have a Panasonic KX-TG2431 telephone (so others can reach me when I am in o ther parts of the building) hooked up to one of the FXS ports. When the other end hangs up, I get the usual CPC disconnect signal. After the CPC, sometimes it will go to a dialtone, and other times a

We are running asterisk with a single POTS line for local calls and a voip line for long distance. Whenever we receive a call on the POTS line it is more than likely, but not always, going to have significant distracting echo. In addition to that there is occasional heavy crackle or static. I have tried to follow the guidelines at :

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel

Hi, I have received a new card TDM400P revision E, from digium. When I tried to modprobe wcfxs it gave me the following errors: Freshmaker version: 63 Freshmaker passed register test ProSLIC on module 0 insane (1) 255 should be 2 Module 0: Not installed ProSLIC on module 1 insane (1) 255 should be 2 Module 1: Not installed ProSLIC on module 2 insane (1) 255 should be 2 Module 2: Not installed

How I change my configuration to reduce this issue. I have this setting on my zapata.conf signalling=fxs_ks group=1 callgroup=1 pickupgroup=1 channel=1 signalling=fxs_ks group=2 callgroup=1 pickupgroup=1 channel=2; singalling=fxs_ks group=3 callgroup=1 pickupgroup=1 channel=3; singalling=fxs_ks group=4 callgroup=1 pickupgroup=1 channel=4 and for outbound calls I have this context on my

I have tried to get my TDM400P card to automatically dial a number or run an application when I pick up the phone without much luck. After reviewing the email archives, config files and source to chan_zap.c it appeared that all I had to do was set "immediate=yes" in the zapata.conf file and have a default number in the TDM400P's context (ex. s,1,Directory(default)). So far I have

Hello, I have few questions about Asterisk. I installed Asterisk from CVS on FreeBSD and I made cvsup 2 days ago. 1.I couldn't find Asterisk version using "asterisk -V" command. How can I to find version information? 2.I am using Wildcard X101P (FXO) and Wildcard TDM400P REV E/F (FXS)on it. I tried Asterisk CallerID feature, but unable to get it. I tried callerid signaling V23,

I have an Asterisk@Home 1.3 server (Asterisk 1.0.9) and recently added a TDM400P with (1) FXO card on port 4. Inbound calls are always successful but outbound calls fail 75% of the time with intercept messages from my dial tone provider that include "we're sorry, your call did not go through", and "we're sorry, when placing a local call it is now necessary to dial an area

Hi, I'm relatively new to Asterisk, and I'm looking to build a tiny system for home use. For context, at home I've got a line from Vonage (last I heard, they won't give out SIP credentials and let you use random hardware/software), which comes out as an analog line with a dialtone, and I'll be treating that as if it were a regular PSTN connection. I also work from home,