Displaying 20 results from an estimated 2000 matches similar to: "digium dev kit - X100P & TDM400P"
2004 Apr 12
2
TDM400P Issues
Hi,
I just got my TDM400P card (2 modules) and i installed it no probs. The
card is detected fine, but for some reason when I add the card to
zaptel.conf i get the following error:
--snip--
ZT_CHANCONFIG failed on channel 2: Invalid argument (22)
Did you forget that FXS interfaces are configured with FXO signalling
and that FXO interfaces use FXS signalling?
--snip--
My /etc/zaptel.conf looks
2005 Aug 13
3
TDM400P Card (Rev G) with bad FXS module?
I think I have a bad FXS module on my TDM400P.
Channel map:
>>
>> Channel 01: FXO Kewlstart (Default) (Slaves: 01)
>> Channel 02: FXS Kewlstart (Default) (Slaves: 02)
>>
>> 2 channels configured.
>> ZT_CHANCONFIG failed on channel 1: No such device or address (6)
The zaptel loads ok, but the wctdm reports No such device or address and
stays loaded. The
2007 Mar 01
1
TDM400p Loaded only once
Hi
when I turn on my PC I able to load the drivers and start my card,
if I reboot the PC I have the following error
ztcfg -vvv
Zaptel Configuration
======================
Channel map:
Channel 01: FXS Kewlstart (Default) (Slaves: 01)
Channel 02: FXS Kewlstart (Default) (Slaves: 02)
Channel 03: FXS Kewlstart (Default) (Slaves: 03)
Channel 04: FXS Kewlstart (Default) (Slaves: 04)
4 channels
2005 Aug 12
2
Possibly bad FXS module in TDM400P?
I've got the latest zaptel and cvs asterisk software loaded on my phone
server running FC3. And yes, It's fully updated and udev is setup
correctly. I've got a TDM400P with one FXS and one FXO module
installed. When I load zaptel and wctdm and run ztcfg -vvv, I get this:
[root@asterisk ~]# ztcfg -vvv
ZT_CHANCONFIG failed on channel 1: No such device or address (6)
Zaptel
2005 Jun 17
2
PLEASE HELP X100P no responding
[root@server ~]# modprobe zaptel
[root@server ~]# modprobe wcfxo
ZT_CHANCONFIG failed on channel 1: No such device or address (6)
FATAL: Error running install command for wcfxo
[root@server ~]# ztcfg -vvv
Zaptel Configuration
======================
Channel map:
Channel 01: FXS Kewlstart (Default) (Slaves: 01)
1 channels configured.
ZT_CHANCONFIG failed on channel 1: No such device or address
2003 Apr 28
9
Dialing using X100P
My setup:
X100P and Quicknet PhoneJack.
I can't seem to properly set up a Zap channel for my X100P.
Here are some of my configurations:
[zaptel.conf]
fxsks=1 #X100P
fxoks=2 #Quicknet PhoneJack
defaultzone=us
loadzone=us
[zapata.conf]
[channels]
context=local
signalling=fxs_ks
channel->1 ;X100P
[extensions.conf]
...
[local]
exten=>_NXXNXXXXXX,1,Dial,Zap/1
;I'm pretty sure the
2006 May 25
3
X100P fails to initialize
So I took a chance with an X100P knock-off on eBay. I'm running Asterisk +
FreePBX on a PowerMac G3 (beige desktop) using Slackintosh 10.2 and kernel
2.6.16.16. Everything has been fine up until now.
I compile the 1.2.5 Zaptel drivers without a problem, get the udev
configuration in, modprobe zaptel, and finally modprobe wcfxo. At this
point, I get the message:
ZT_CHANCONFIG failed on channel
2004 Aug 26
1
Newbie needs help - Dev_Kit_Lite installation problem
Installing DevkitLite hardware (Very similar to John Lange's post on Tue
Oct 08 2002)
I cannot get anything to work on the phone connected to the s100u. I dont
know what to do.
Can someone please help me?
I used the sample configuration files from digium documentaion that was
supposed to be "sane" defaults for the kit.
Very similar to John Lange's post on Tue Oct 08 2002
Here
2009 Apr 11
1
asterisknow 1.5 with X100P and TDM400P
Hi All,
Sorry if this has been around a millions times.. I have been off this
list for a few months now..
I have installed the latest asterisknow (upgraded asterisk to 1.6 as
well) and I am having a hard time getting my X100P and TDM400P working..
Its all new to me with dahdi because my old server is still running
Asterisk 1.0.2 so there have been lost of changes..
Can someone point me in
2004 Oct 02
1
Second X100P card won't work
Greetings all,
I've just put two X100P cards to my box and despite trying everything I
can find on the web, I can't get the second one to work.
I've edited /etc/modules.conf so that ztcfg doesn't run automatically.
To start, I run:
/sbin/modprobe zaptel
/sbin/modprobe wcfxo
/sbin/ztcfg
/sbin/modprobe ixj
and ztcfg says:
ZT_CHANCONFIG failed on channel 2: No such device or
2005 Sep 13
4
Fedora Core 4 not recognizing X100P cards
I am getting quite frustrated today, so please bear with me.
I just installed Fedora Core 4 (was running RedHat 9 with a working
Asterisk)
now my Fedora does not appear to be recognizing my X100P (clone) at all.
Hardware browser just shows them as unknown device. driver: hisax
So, of course, my zaptel drivers do not work and therefore my asterisk does
not work.
any help would be greatly
2005 Jul 12
3
Help Configuring TDM04B
Hi:
I had an fxo card from Digitnetworks and it was
working fine on my Asterisk box. I then replaced it
with TDM04B. I changed the zaptel and zapata to
include the four channels. When I run ztcfg, I get
configuration errors:
Channel map:
Channel 01: FXS Kewlstart (Default) (Slaves: 01)
Channel 02: FXS Kewlstart (Default) (Slaves: 02)
Channel 03: FXS Kewlstart (Default) (Slaves: 03)
Channel 04:
2004 Jun 18
5
Problems with X100P
All,
I'm having trouble getting the X100P working.
Lsmod shows :
zaptel 179808 0
I did a .
# modprobe zaptel
and here is my zaptel.conf (comments omitted)
__SNIP__
fxsks=1
loadzone = us
defaultzone=us
__SNIP__
Here is zapata.conf
__SNIP__
[trunkgroups]
[channels]
context=default
switchtype=national
signalling=fxo_ls
rxwink=300
usecallerid=yes
hidecallerid=no
2003 Sep 13
1
ZT_CHANCONFIG failed on channel 1: Invalid argument (22)
no matter which way I have my /etc/zaptel.cfg
this only started happening after a yesterdays CVS update
to my zaptel source...
Line 1: fxoks=1
Line 2: fxsks=2
Line 23: loadzone=us
Line 28: defaultzone=us
<End of File>
Zaptel Configuration
======================
Channel map:
Channel 01: FXO Kewlstart (Default) (Slaves: 01)
Channel 02: FXS Kewlstart (Default) (Slaves: 02)
2 channels
2007 Apr 19
6
ZT_CHANCONFIG failed on channel 1: No such device or address
I have had a TDM400 with 2 FXO and 2 FXS working for ages (>12 months). It has stopped working. All four green lights are still lit. I have rebuilt zaptel and asterisk and restarted but the problem persists.
/sbin/ztcfg -vvvv
Zaptel Configuration
======================
Channel map:
Channel 01: FXO Kewlstart (Default) (Slaves: 01)
Channel 02: FXO Kewlstart (Default) (Slaves: 02)
Channel 03:
2006 May 09
2
Problems with TDM400P and FXO modules
Hi , I have an asterix (1.2.7.1) box with 3 TDM400P and 10 FXO modules, and
zaptel (1.2.5).
The problem is that 6 modules can't be initaized and i get the folowing
error:
May 7 09:17:37 WARNING[7739] chan_zap.c: Unable to specify channel 9: No
such device
May 7 09:17:37 ERROR[7739] chan_zap.c: Unable to open channel 9: No such
device
here = 0, tmp->channel = 9, channel = 9
ztcfg output
2009 Sep 27
3
Problems with Digium TDM400 card
I had a working Asterisk 1.4.24.1 installation on SUSE 9 Linux but SIP only. I then downloaded and installed latest Zaptel and could not get Zaptel working. So I downloaded Asterisk again and re-installed.
But still problems:
Here is my ztcfg output:
asterisk:/etc/asterisk # ztcfg -vvvvv
Notice: Configuration file is /etc/zaptel.conf
line 4: Unable to read Zaptel version information.
Zaptel
2006 May 04
2
Unable to get TDM400p working
This has got to be a stupid error I'm making...
I have been experimenting with different hardware and software
configurations before I decide what to use as a production platform. Up
until just recently things were going well.
But now it appears I'm unable to get access to my TDM400p from Asterisk. I
know the TDM card works fine, used it in another machine where it
performed flawlessly.
2004 May 19
4
TDM400P problems with 1 FXS, 1 FXO
Hi-
I'm totally stumped configuring my TDM400P with one FXS and one FXO
module. Before I got the FXO module, I used to have an X101P, and
everything was working very well. Now * doesn't seem to recognize the
FXO channel. I've searched the wiki and the list archives. Stock Debian
3.0 stable installation. Any advice? Thanks.
-- David
Here's my configuration:
modprobe zaptel
2005 Jul 22
1
Problem with Zaptel FXO..
Hi all, i've installed AMP and Asterisk following the INSTALL file and i have
a problem with the TDM04B with 4 FXO:
[root@srvoip ~]# ztcfg -vv
Zaptel Configuration
======================
Channel map:
Channel 01: FXO Kewlstart (Default) (Slaves: 01)
Channel 02: FXO Kewlstart (Default) (Slaves: 02)
Channel 03: FXO Kewlstart (Default) (Slaves: 03)
Channel 04: FXO Kewlstart (Default)