similar to: Warning Messages

<P>hi,</P> <P>Can anybody pls tell me how to activate loggin CDR on mysql db. I tried&nbsp;editing the /etc/asterisk/cdr_mysql.conf file and recompiling asterisk, it didn't work. Normal loggin on Master.csv file works fine.</P> <P>Thank you inadvance,</P> <P>Surajee</P> <P>&nbsp;</P><br> --------------This mail sent

<P>hi Everyone,</P> <P>We are configuring an ISDN PRI E1 with an E100P card, when you load the drivers, and starts the asterisk, cards also starts fine, givin following output,</P> <P>*CLI> <BR>&nbsp; == D-Channel on span 1 up<BR>&nbsp;&nbsp;&nbsp; -- B-channel 1 successfully restarted on span 1<BR>&nbsp;&nbsp;&nbsp; --

Hi List, I am facing the reverse problem as stated here.I am using ATA 186 to make and recieve call to * through OH323 driver. When I use G711 codec in the ATA to make call then then as soon as i dial an extension the * crashes with 'segmentation fault'. But the same scenerio works fine when i use 723 codec in the ATA .I can dial the number and extension very well/(I have 723 support in

<P>hi everyone,</P> <P>I know this issue has been raised many times before, i think still the problem remains. When a call is made through a Zap channel, whether it is actually made or not (irrespective of whether, engaged, busy, or actually answered), asterisk logs it in CDRs as a call made. This makes it impossible to do an accurate billing. Has anybody found a way to overcome

Hi, I'm having two problems. First - I'm using the xten x-lite program to communicate with asterisk, and everything works fine except that DTMFs are not transferred. I've set DTMFMODE to inband on both the sip.conf file and the x-lite configuration, and still it doesn't work. Anyone had this problem before>? Second thing: I get a WARNING:[1209214400]: File dsp.c,

hi, The prob is when we ring 2 channels simultaneously, only 1 channel is actually ringing. In our configuration, the Asterisk box is connected to an E1 channel bank, where 15 analog extensions are conencted to channelbank inturn. We tried following, Dial,Zap/g4/444&Zap/g4/448|20|t Heres the output, -- Executing Dial("IAX2[trunk10@trunk50]/1",

Hi, I am calling from a grandstream phone with g723 codec through * to iconnect. Incoming context as well as outgoing context set to g723.1 codec in *. Call get connected and I can talk. However I get the following warning, which scrolls on my screen until I hang-up. [root@asterisk sath]# cat g723.1 - Executing SetCallerID("SIP/-08122ae0", "1001") in new stack --

What does it mean ?? WARNING[265236]: File dsp.c, Line 1198 (ast_dsp_process): Unable to detect process 2 frames WARNING[265236]: File dsp.c, Line 1198 (ast_dsp_process): Unable to detect process 2 frames WARNING[265236]: File dsp.c, Line 1198 (ast_dsp_process): Unable to detect process 2 frames -------------- next part -------------- An HTML attachment was scrubbed... URL:

<DIV><FONT face=Arial size=2>hello All,</FONT></DIV> <DIV><FONT face=Arial size=2></FONT>&nbsp;</DIV> <DIV><FONT face=Arial size=2>our Asterisk pbx is sitting behind a normal analog hardware pbx, we have to dial 9</FONT></DIV> <DIV><FONT face=Arial size=2>to take an outside call through the hardware pbx, our

hi, I have a problem in call time out, An ISDN PRI E1 from PSTN and another ISDN PRI E1 from a Nortel PBX is conneted to my server. But when i do a Dialout(from both E1s)the calls do not timeout. For ex. Dial(Zap/g4/123456|20|t) suppose other side is ringing and is not answering. even after 20 seconds, call doesn't get timeout pls gv me a solutions.. its really urgent.. Surajee

hi all I'm being spammed by these messages in the console (see below) and sound doesn't work with today's cvs. I rolled back a week, and it works fine. In addition to the sound problems, I had to enable inband dtmf squelch on the dilnk mgcp phones. if not, each pressed key was counted twice NOTICE[245776]: File chan_mgcp.c, Line 710 (mgcp_rtp_read): MGCP ast_dsp_process

hi .. I have finally managed to get Chan_H323 & G729 working flawlessly, thanks to some help from Jerry McNamara. For those out there who are stuck with the same problem the procedure is : 1. install on RedHat 8.0 and nothing else (RH9 doesn't work!) 2. Install asterisk, zaptel etc. the normal way 3. Compile Pwlib & oH323 with versions taken from nufone's site

hi ! I have asterisk with Licensed G.729 codec enabled. Whenever I make a call using this codec a warning apears as, WARNING[18450]: File dsp.c, Line 1106 (ast_dsp_process): Unable to detect process 256 frames WARNING[18450]: File dsp.c, Line 1106 (ast_dsp_process): Unable to detect process 256 frames WARNING[18450]: File dsp.c, Line 1106 (ast_dsp_process): Unable to detect process 256 frames

Hello list! I only can make successful calls if I disable gsm with "disallow=gsm". As soon as I allow gsm the following appears at the console. There are much much more Lines with "File dsp.c, Line 1198" but I cut them for a better survey : --------- Log Start ------------- Asterisk Ready. WARNING[5126]: File chan_sip.c, Line 464 (retrans_pkt): Maximum retries exceeded on

hi, Can anybody pls tell me, how to increase the time gap between 2 digits when you transfer a call. ie, the operator answers the call, and presses hash key to transfer, and then enters the extension number, some times, it timeouts too quickly before the operator enters the whole extension number (may be bcos the operator is slow). I tried the following, but it doesn't seems to be helping

Hi can anyone help me on this error msg?? dsp.c:1467 ast_dsp_process: Unable to process inband DTMF on 2 frames thnx St

Hi, I have a problem with asterisk-0.5.0 which I don't understand. The monitor says when making a call: *CLI> -- Executing Dial("SIP/roger-c456", "Modem/ttyI0:BYEXTENSION|60|tTm") in new stack -- Called ttyI0:1234567890 WARNING[196621]: File dsp.c, Line 1198 (ast_dsp_process): Unable to detect process 2 frames WARNING[196621]: File dsp.c, Line 1198

Anybody has figured out why asterisk + snom have such bad quality using GSM? When I use GSM I see such messages dumped on asterisk console: WARNING[14351]: File dsp.c, Line 1198 (ast_dsp_process): Unable to detect process 2 frames WARNING[14351]: File dsp.c, Line 1198 (ast_dsp_process): Unable to detect process 2 frames WARNING[14351]: File dsp.c, Line 1198 (ast_dsp_process): Unable to detect

Hi, I am trying to install chan_capi, with asterisk (cvs) on Suse 9.0, but I get the following error: ====== linux:/usr/src/chan_capi-0.3.1 # make gcc -pipe -Wall -Wmissing-prototypes -Wmissing-declarations -g -I/usr/include/asterisk -D_REENTRANT -D_GNU_SOURCE -O6 -march=i686 -DCAPI_ES -DCAPI_GAIN -DDEFLECT_ON_CIRCUITBUSY -DCAPI_SYNC -Wno-missing-prototypes -Wno-missing-declarations -DCRYPTO

When I saw the update for Cisco Phone RTP issue I thought I would try it. Unfortunately chan_capi wont compile on this update. Can anyone recommend a good * release for Capi, Bri ISDN and Cisco 7940's SIP 6.3. Or will CHAN_CAPI also be updated ? Running Eicon Diva Bri Cards. Error: chan_capi.c:1187: too many arguments to function 'ast_dsp_process'