similar to: Cisco AS5300 -- Not hearing anything

Hello, I have a Cisco AS5300 connected to Asterisk (1.6.2.9) Between 15-16 minutes, the call is disconnected without reason. Here is what is displayed in the debug: Received an SDES from 10.4.0.10:17399 -- Got SIP response 420 "Bad Extension" back from 10.4.0.10 -- Stopped music on hold on SIP/as5300-1-0000004d == Spawn extension (dialin, 065939191, 2) exited non-zero on

I've previously been using G711alaw on both the AS5300 and the phones but feel the need for a less bandwidth hungry codec for those users that are connected behind ADSL and so was investigating G.729 but .. Firstly I found that on my AS5300 I have either G.729r8 or G.729br8 and on the 7940 phones I have G.729a, I'm not sure which interoperate the best with each other and so was wondering

Hi Now, my Cisco AS5300 sent call to my asterisk, but two problems: When i call the phone number, i have: [Oct 28 06:01:16] NOTICE[12813]: chan_sip.c:18160 handle_request_invite: Call from '' to extension '0426000000' rejected because extension not found. [Oct 28 06:01:18] NOTICE[12813]: chan_sip.c:18160 handle_request_invite: Call from '' to extension

Hi Isn't this exactly what we _don't_ wanna do?! =) I suppose TDM and VoIP is supposed to interconnect not to be separated. i think it's nice with a busy list, it means some real hot stuff is happening, and that's good! rgds /staffan -----Ursprungligt meddelande----- Fr?n: Luciano Ramos [mailto:lramos@telviso.com.ar] Skickat: den 9 januari 2004 14:12 Till:

Hi I have finished the installation of my VoIP basic configuration ... Actually: - All calls from my E1 are received by a Cisco AS5300 and sent to my Asterisk (in G711 by SIP). - All user are connected by SIP to the Asterisk - All calls from User are sent by asterisk to the Cisco AS5300 Now, i want see if i can supply T38 Fax Gateway .... I am search to: - Cisco Receive all

Hey all, I have an as5300 I use for dial in customers, we have 4 PRIs on it. We have a few free channels on it. I'm wondering if I setup SIP on the as5300 I can have asterisk use the free channels for dial out. I'd still have to use my TDM04B for incoming calls, but at least I can expand my outgoing. Anyone done anything like this before? I've never messed with VoIP on Cisco

Hi i test a new equipment on my backbone: a Cisco AS5300 with voice dsp ressource connected at a E1 Voice Link. I want that all call incoming on the cisco 5300 are sent to Asterisk and all Asterisk outgoing call are sent to Cisco AS5300. Actually, i configure the AS5300: isdn switch-type primary-net5 ! voice service voip sip ! voice class codec 400 codec preference 1 g711alaw codec

Is it possible to terminate calls via SIP on a Cisco AS5300? Did anyone do it? How? Do i need an special IOS version? Ive been trying to compile the OpenH323 channel for the last month, but errors still happens. Thanks in advance. -------------- next part -------------- An HTML attachment was scrubbed... URL:

hi All Any body already setup asteriks call routing to Cisco AS5300 with SIP Server ? i need informations sample config for that, or can show how to route docs . thanks Dirgan --------------------------------- Meet your soulmate! Yahoo! Asia presents Meetic - where millions of singles gather -------------- next part -------------- An HTML attachment was scrubbed... URL:

I have my server configured to send to send all PSTN traffic to my Cisco AS5300 gateway via SIP. I use the following line in the extensions.conf file to accomplish this: exten => _NXXNXXXXXX,1,Dial(SIP/1${EXTEN}@10.1.1.1,240,T) Unfortunately, when I removed the T from the end of the statement, the calls still complete, but they drop as soon as the called party answers the phone. I thought

Hi, We need help in enabling g729a codec for our SIP peer that's using Cisco AS5300. Our codec is purchased from Digium. We are able to dial out the numbers and answer the call, but there's no audio. This is when only g729a is allowed. We noticed when they also allow ulaw codec on their side, the codec used falls back to ulaw and the problem is gone. -------------- next part

I am trying to send calls from an AS5300 to Asterisk via e1 and I get this bit of information in place of routing information Going to extension s|1 because of Complete received Accepting call from '' to 's' on channel 1, span 1 Here are the relevant zaptel and zapata pieces. span=1,1,0,ccs,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 signalling=pri_cpe switchtype=national

Hi all, I realize this is OT. I just got a Cisco AS5300, and I need to configure it like such: Asterisk -----(H323/SIP)------> Cisco ----- (E1/PRI)------->Telco So calls originate from the Asterisk side (registered users on SIP or just ZAP phones), and they go out H323 or SIP to Cisco, where they go out PRI. I have the Asterisk side sorted :) (either H323 or SIP), I need help in the

Greetings, I am attempting to configure an AS5300 to provide a SIP based gateway to the PSTN from Asterisk. I have been unable to identify through the docs how specifically this should be configured in Asterisk and have not been able to get things working through trial and error. I am sure I am missing something fairly obvious here but any guidance (or example cfgs) would be much appreciated.

Hi i'm trying to connect to the PSTN in the following way sip ATA -> * -> gnugk -> Cisco AS5300 -> PSTN I'm using asterisk CVS-HEAD-06/01/05-14:33:15 running over RH EL3 Asterisk-Oh323 0.7.2 pre1 Open H323 v1.13.5 pwlib v1.6.6 and I'm having a lot of trouble, gnugk and * both have public ips and are not behind any type of firewall, the sip ATA is behind a firewall and

Hello, I have 5 digium's g.729 codecs and succesfully register with asterisk, I have incomming call from my cisco AS5300 to Asterisk through IP. But Asterisk always use g711 ulaw instead of g.729. When I disable all other codecs other than g.729 in both cisco and asterisk, calls get dropped once connected. The codec list show on my cisco AS5300 for g.729 are: g729r8 g729br8 I suspect that

Hi, I had previously posted about connecting an AS5300 to * via SIP/H323. I got it to work via SIP, but only 1 call at a time would work, and if a user from the * side hung up, the cisco would'nt catch the hangup. I an now trying to hook up to the cisco via E1, with a Sangoma A101 card in my * box. I would like it such that I call from * via E1/PRI to the cisco, and call out via R2 to

Guys. I need some advice on some h323 issues. I need to test connectivity from Asterisk to a Cisco AS5300 that has PSTN lines and to cisco 3600 voip routers. H323 needs to be used here but I was wondering if anybody has linked Asterisk to these Cisco routers before? Thank you for any pointers.

I wouldn't expect you to be using RFC3389 if your using A-law, can you include your IOS version and IOS config file ... I have not specified any allow's or disallow's in my * config for the codecs with my 5300, I also use Cisco 79xx phones and I use the option within the phones config file to select the preffered codec and when I change this to G.729/A-law/U-law all works perfectly

I've got asterisk working great with cisco 7905 sip phones. I've just got one issue that I can't figure out. I have a 5300 connected to the PSTN via PRI. When I send a call from the 5300 to asterisk it will ring the 7905 phone for 4 seconds then drop. This is because the only message asterisk sends to the cisco is the 100 trying message. The 5300 receives that and sends a call