similar to: Zaptel cards, working FXS and SIP, no audio?

I have just received a T100P and an Adtran TSU 600 in the mail. I seem to be having a problem with the T100P card. So far I have done the following: vi zaptel.conf fxoks=1-22 fxsks=23-24 ... vi zapata.conf ... signalling=fxo_ks ... channel => 1-22 ... signalling=fxs_ks ... channel => 23-24 I then run modprobe zaptel modprobe wct1xxp ztcfg -vv There are no errors to report. In

List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to

Please explain the relationship between modules from the driver (wctdm), the /etc/zaptel.conf file and zapata.conf. Specifically, if I have a FXS module 0 and FXO module 1, what should be used in zaptel.conf and what should be used in zapata.conf? Then finally, in extensions.conf, what is the Zap channel for dialing out? Zap/? % dmesg Module 0: Installed -- AUTO FXS/DPO Module 1:

I have an intermittent problem with the one FXS line that I have. On most calls, the first ~5 seconds of the call has a loud buzzing noise on the line. After 5 seconds or so, it fades off to nothing, and the sound quality is great. Searching for "buzzing" on the list doesn't give a whole lot to work with. The buzzing happens on calls that are routed over both my FXO line and

Hello, everyone After having spent several time to look for any solution for my problem, I decided to write here. Here is the problem got a Digium X101 FXO card and Digium TDM400P alias freshmaker (1 fxs module on it on first port ) in my asterisk box. The X101 works perfectly. The problem comes from the TDM400, when i plug a tested working phone on it , i get no dialtone; the goal is to

Hi, I am trying to do the world's most simple install. I have a Wildcard TDM400P with 3 ports: 1 FXS on port 1 and 2 FXOs on ports 3 and 4. (i'm not using port 3 for now, put want it for expansion purposes) I simply (to start with) am looking to have the FXS phone ring when an FX0 port is dialed. I would also like to be able to place outgoing calls on the FXS through the FXO. Right

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel

I've got the latest zaptel and cvs asterisk software loaded on my phone server running FC3. And yes, It's fully updated and udev is setup correctly. I've got a TDM400P with one FXS and one FXO module installed. When I load zaptel and wctdm and run ztcfg -vvv, I get this: [root@asterisk ~]# ztcfg -vvv ZT_CHANCONFIG failed on channel 1: No such device or address (6) Zaptel

Evening, My latest asterisk box is having a difficult problem. It is configured with one TE210P and TDM400P with four FXO modules. I'm running FC6. The TE210P only has a single PRI. When the system boots, it is completely random what order the zaptel modules will get loaded in. Sometimes zttool shows the FXO as the last span, sometimes as the first. When it does load as the first, which

Hi to all, I have been using Wildcard TDM400P with four fxs modules and it was working fine now I have added another Wildcard TDM400P with four fxs modules . So there are total 8 ports for 8 hard phones. I have modified following configurations In /etc/zaptel.conf loadzone=us defaultzone=us fxoks=1-8 in /etc/asterisk/zapata.conf context=headoffice signalling = fxo_ks

Hi All, Which is the best signalling to use when connecting an FXS inteface on a TDM400 to a standard telephone. I see that all examples use fxo_ks, but it is my understanding that kewl start is really designed for connections to the CO so that hangup etc. can be detected. So does it make any sense to configure a telephone for fxo_ks? Or should it be configured for fxo_ls? Regards Garry Taylor

Can anyone explain to me the difference in zaptel.conf and zapata.conf? I'm trying to get a real clear understanding of them but its getting a little murky in places. I will be setting up a PBX running asterisk with 2 T100P cards. I will be bringing a 23 channel PRI into one card and connecting the other card to a Nortell 24 channel FXS channel bank. As I understand it zapata.conf is

Hi I've problem, i cant get tone on a FXS ZAP channel my configuration are: -- zaptel.conf -- fxoks=1 --zapata.conf -- [channels] immediate=yes context=bell signalling=fxo_ks channel=1 --extensions.conf -- [home] exten => 500,1,Dial(IAX2/guest@misery.digium.com/s@default) [bell] exten => s,1,SetCallerId(${CALLERID}) exten => s,2,Dial(${PHONE},16,tr) ANY IDEA?

As best i could figure it out, I've installed dahdi and rc4. My TDM400P doesn't answer fxo or fxs. /etc/dahdi/system.conf: loadzone = us defaultzone=us fxoks=1,2 fxsks=4 /etc/asterisk/chan_dahdi.conf: [house-phones] context=internal ; Uses the [internal] context in extensions.conf signalling=fxo_ks ; fxo_ks Use FXO signalling for an FXS chanel dahdichan => 1 ;

I am running Asterisk 1.6.2.17.2 with a Openvox A400 card with 2FXO/2FXS modules. I'm trying to set-up things to route analog fax calls from a FXO port to an analog fax machine on a FXS port on the same card. Outgoing faxes work just fine. But incoming faces are routed to the right DAHDI extension, but the call dropped right as the fax machine rings for the first time. The fax machine

Feel free to hit me with a cluestick; maybe it will jar something lose... I'm running a stock *@home 0.6 install and after four days of excrutiatingly annoying debugging, I finally came across the obvious problem. The zaptel driver is reading /etc/zaptel.conf; which by default configures one FXS Kewlstart channel. Asterisk, according to "full" log, will see the first channel, then

HI Here is a question about the fxs of the zaptel card which is set a number to use in the inter as common analog phone. When I also use ${CALLERID(num)}to get it's number, it also could not be done. At this time ,the fxs phone does not get any relation with the outbound which is like PSTN and so forth. It just set the phone number and extension in the * for inter used . Could you tell me

Hi, Is it possible to create a clear zaptel channel which doesn't require to be picked up? The requirement of my client is to open a clear channel to a recorder which starts recording certain message. Currently the channel which is created by zaptel requires the other end to answer the call, and the recorded can't answer, so the channel get hung up after a certain number of rings. Zaptel

Hi I was using the delivered Ubuntu 1.6.x packages but I wanted to look at gtalk integration so I downloaded, compiled and installed the source (after removing the Ubuntu packages) have installed the following: asterisk-1.8.0 dahdi-linux-complete-2.4.0+2.4.0 libpri-1.4.11.5 I copied my config back into place and most seems to work, but I cannot get my phone that is plugged into the Wildcard

Hello all, I've got a T100P connected to an Adtran TA750 with a T1 crossover... This connects to a patch panel with phone ports. The Adtran is fully populated with FXS cards. All I get on any phone port is a fast clicking noise... No dialtone. Asterisk 'sees' the card, (the channels show up in /proc/zaptel). Incoming calls are routed to the zap/x channel, but no ring. I'm