similar to: zt_pri_errors: PRI got event: 8 / 6

Hello all, i'm experiencing a list of unpredictables hangup on SIP phones using a PRI E100P Card. All i can see in logs is " WARNING[81931]: File chan_zap.c, Line 5402 (zt_pri_error): PRI: Read on 37 failed: Unknown error 500" I receive a lot of these errors in asterisk/messages. It doesn't seem to be strictly linked to hangups, since i have dozen of these messages per

I've to project and build a fresh new box with * on. Basically, i'll have this situation: The office is connected to the phone carrier with a PRI. I need to let users continue to use their analog phones in a office, and an IP-phone based solution on the remote office, that will call using outside using the PRI on the first one. PRI---> Asterisk ---> Analog phones |

I'm using happily this cheap phones, but I still have a little problem. Configuring the phone is extremely easy on * and I've a couple of them perfectly working, except when i try to call some toll-free number (in italy 800xxxxxxx ). If the number called is an IVR system, often with GrandStream (but also with Cisco 7905.h323) it's impossible to make the menu choices via the Dialpad.

Hi, I am running * with E100P board. At least every our I got an Error 500 message and ISDN-PRI restarts: Jan 10 12:53:02 WARNING[98311]: File chan_zap.c, Line 5758 (zt_pri_error): PRI: Read on 27 failed: Unknown error 500 Jan 10 12:54:27 WARNING[98311]: File chan_zap.c, Line 5758 (zt_pri_error): PRI: Read on 27 failed: Unknown error 500 Jan 10 13:33:01 WARNING[98311]: File chan_zap.c, Line

Greetings, I need if possibile an explanation on how to manage the incoming callerid for an incoming call. Let me explain the situation: We have two different companies in this office that shares the same PBX (* box). Each company have its own number for the incoming calls. What i'd like to implement is something that, depending on the incoming line that is involved in the call, plays a

hi guys, I have a little problem maybe you can help ... I have an asterisk setup, with an E100P, and an ISDN-PRI 30 channel line from the telco going into it .. the E1 line is OK, because plugged into a Lucent Portmaster 4 it works OK .. plugged into the asterisk box I just get an engaged tone, and asterisk posts this message on screen : WARNING[1167272000]: File chan_zap.c, Line 5275

I need to configure an * box to connect to a primary * box which is attached to a PRI in order to make calls using both the same E1 connection. I know the best solution is to use IAX (altough i could connect the IP phones on the remote site directly to the main * box that is VPNed with the remote one). I've some doubt on how to config IAX to work in this situation. I think that: On the

Is there any way to run asterisk without a fxo card? I am looking only run SIP and a single fxs card.

Hi, I'm installing E100P for isdn pri line. My configuration are like this. zaptel.conf ======================================= span=1,0,0,ccs,hdb3,crc4 loadzone = us defaultzone=us bchan=1-15 dchan=16 bchan=17-31 zapata.conf ================================================= [channels] context=default switchtype=euroisdn context=default signalling=pri_net usecallerid=yes

Hi! I have the chance to play with a couple of E400P cards, each installed in a IBM e330 XSeries servers (2 x 1GHz P-III CPU 2 Gb RAM, 36Gb SCSI HDD with RH8.0 2.4.18-smp kernel), and I'm trying to test/benchmark this e330/E400P combo generating calls thru /var/spool/asterisk/outgoing One e400P if doing the carrier work making calls and the other just receives the calls: Server#1

After a long working evening yesterday, now my * box place and receive calls with H323,SIP and ISDN line. Calling from the office to an outside line, happens: - If I call a mobile number and the called answers, all goes ok - If I call a number at home/office, and it's answered , all goes ok - If I call a toll-free number with an IVR system, nothing happens: it continues to ring indefinitely

Just cross pairs 1-2 and 4-5 1 <--> 4 2 <--> 5 Never done an E1, but I think it's the same for a T1 4 wire cable. Tim Thompson Commercial Sales Engineer http://www.amatechtel.com (806) 722-2227 -----Original Message----- From: bam [mailto:bam@cqm.co.uk] Sent: Monday, December 29, 2003 9:12 AM To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] E100P pinouts

Hi, I am having some problems mentioned below, the box is in production live environment with traffic around 30 - 100 calls. I am running T/E410P in a Dual P4 xeon with HT disabled. I am using zaptel 0.9.0 and asterisk stable 1 release. There is no gui, just mysql, perl (small script) and asterisk. System runs very smoothly if the calls are around 40-50 and comes one by one , however sometimes

Hi ! I'm trying to configurate my first asterisk system. My test plant has an E100P Card and a 4 FXS TDM 400P card. I've an E1 configured for 15 channels. Telco says that crc4 is configurated so my zaptel.conf is: loadzone = it defaultzone=it span=1,0,0,ccs,hdb3,crc4 bchan=1-15 dchan=16 unused=17-31 fxoks=32-35 zttool shows no alarms. I've also tried changing the timing

Hi, I've got an important question: I use an E100P directly connected to PSTN, but it does not *really* work as it should be: exten => 1000,1,Dial(Zap/1/1234) BUT: It does NOT dial "1234" but it says in debug mode: -- Called 1/72976451 Apr 26 00:53:00 WARNING[10251]: chan_zap.c:5979 zt_pri_error: PRI: !! Facility message shorter than 14 bytes -- Channel 1, span 1 got

I need help creating a channel for my phone device (Quicknet PhoneJack). I have installed and loaded the driver and phone devices listen in /dev (phone0 - phone15). [phone.conf] mode=dialtone format=slinear device => /dev/phone0 fxoks=2 ;Quicknet PhoneJack [extensions.conf] ... exten=>_NXXNXXXXXX,1,Dial,Phone/phone0 ... When I try to make a call, I get the following output: Executing

Dear All, I'm having a problem with my Asterisk + E100P Installation in UK (BT PRI). The system functions as expected, and my dial plan works as expected. 30 minutes (or so) after starting the asterisk service I lose the PRI line, and only get this back after a service asterisk restart or reboot. During the failure there is no alarm on zttool, ztcfg show all 31 lines and there are no

Hi I have recently upgraded my Asterisk system (from 1.2 to 1.4) and I have started to notice the following messages when I recieve a call on my Zap channel :- [Mar 11 09:20:17] WARNING[4294]: chan_zap.c:8851 zt_pri_error: 1 copying 5 bytes LLC I have a single PRI ISDN 30 link to a Siemens Realitis DX. Here is my zapata.conf :- [channels] echocancel=no echocancelwhenbridged=no rxgain=-5.0

Hi all: I have problems to setup my zaptel E100P hardware. When I start * after receive the "Asterisk Ready" I see this: *CLI> Jun 22 20:37:55 NOTICE[1133718080]: chan_zap.c:4881 handle_init_event: Alarm cleared on channel 1 Jun 22 20:37:55 NOTICE[1133718080]: chan_zap.c:4881 handle_init_event: Alarm cleared on channel 2 Up to channel 31. anfter this: Jun 22 20:37:55

Hi all- HELP! This is actually a revisit of a problem that I had earlier with E400P's at a customer site. Customer still gets locked up channel problem, but has learned to live with it (channels clear themselves after several minutes). The symptoms, which I believe are directly related: I'm having problems with tons of framing and "read" errors on my E1 connections (and