similar to: T1 slips/BPVs clarifications (was: Help! Problems talking to upstream switch)

Does anyone know how to monitor * to see if they are receiving timing slips on a span connected to a T100P card? I am seeing b-channel restarts quite often and also getting "No D-channels available" warnings from time to time. Yesterday I had all the b-channels crash during a MeetMe Conference. Not good! This PRI is connected to an Avaya Definity PBX that is onsite and located in the

Hi all, I'm sure something similar has been discussed, but one can only wade through the archives for so long. I'm setting up a T1 and my telco has a bunch of questions it wants me to answer. I know much of the TE110p is configurable to do any of this, but I wanted to know if there is an optimal or preferred setup. Any help would be appreciated. Here is the quiz my telco is giving me:

We are currently working to trunk from a Nortel 81C to an Asterisk Server 1.4 running on Red Hat Linux. We have two PRI trunks which work with the exception of the clock slips, which is causing the Nortel to reset the PRIs once a hour. Thanks for any suggestions. 81C MSDL Asterisk Digium TE110P REQ prt TYPE adan dch 10

I am ordering T1-PRI service from local service provider and have a few questions. Is there framing and coding considerations (or is it all one standard), if so what is best? How are calls routed based on DIDs - are these just dtmf tones passed after the call is picked up and treated as normal exten=> definitions? John This e-mail was scanned and found clean by Monroe-Woodbury CSD

Hi, I've searched and searched on the possible problems. If anyone can help me that would be great. Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER) B8ZS/ESF CRC4 error count: 4750 E-bit error count: 5023 Timing slips: 72 1 TE2/0/1/1 Clear (In use) (SWEC: MG2) 2 TE2/0/1/2 Clear (In use) (SWEC: MG2) 3 TE2/0/1/3 Clear (In

I need some help getting a system running for one of my company's plants. I am running AsteriskNow 1.7 with Asterisk 1.6.2.10 and FreePBX 2.8.0.2. My D-Channel keeps bouncing. The telecom tech told me he thought that I might be using the wrong sync source, and I think I might have been, but I changed DAHDI system.conf to "span=1,1,0,ESF,B8ZS" (from

I'm emailing this as the customer in this case, since my carrier appears to be completely unable to solve this. A brief rundown of the problem: - We have several voice lines going through the ADIT, of course into a VoIP type of arrangement. - Voice traffic will become choppy, even drop calls completely, at random but quite often. Modem calls (which we needed unfortunately) are a joke. -

List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to

Hello, I'm trying to set the 3rd span of a new digium quad card as a E&M T1 for Faxes to a Hylafax server. The 1st and 2nd spans are working as PRIs. When I start asterisk, the logs show a signaling error and chan_zap.c dies. I also get an error that it can't read the gains but they are the standard shown below. 2.6 kernel, Debian Stable, * 1.2 svn from feb 2007 my procedure: make

My TE411p does not seem to like to have two PRIs from different telcos (span 1 and span 2). I can get one working, but not the other. However, if I use vpmsupport=0 when loading the wct4xxp module, they both work. But here is the problem, vpmsupport=0 disables the on board echo cancellation. Any ideas? BTW, here is zaptel.conf span=1,1,0,esf,b8zs span=2,2,0,esf,b8zs bchan=1-23 dchan=24

Hi List, After reading a bunch of the docs, list post archives, it still seems that a clear definition of how to clock the T100P card is muddy. zttool says that the link is "INTERNALLY CLOCKED", does this mean the T100P is providing clock, or does this mean the T100P is getting clock from the T1 line side (ergo getting clock from the Telco) ?? If you have sync = 0 then zttool

I have a box with 12 T1s (4 Te410P cards). The PSTN provider is reporting slips and ask me to update the clock source. I have my system.conf set as the following but when I run dahdi_scan only the ports on Card 1 are showing up with syncsrc=1 system.conf : span=1,1,0,esf,b8zs bchan=2-24 mtp2=1 span=2,2,0,esf,b8zs bchan=26-48 mtp2=25 span=3,3,0,esf,b8zs bchan=49-72

I am having trouble getting my T100P and ADIT 600 talking. I have 2 FXO 8 port cards in the ADIT and a T1 controller card. I have a T1 x-over cable connecting two together. Here are copies of the relevant bits of my zaptel.conf and Zapata.conf Zaptel.conf span=1,0,0,esf,b8zs loadzone=us defaultzone=us Zapata.cfg context=default signalling=fxs_ks group=1 channel => 1-24 My

Hello. New to the list. We're in the process of deploying Asterisk. Actually, we're going live tomorrow, and I just found out that my Zaptel cards have been mis-configured. I'll preface this by saying that I have looked in the wiki, read through the samples, and attempted to call Digium (they're closed.) So I'm praying that someone on the list can help me out! I have two

Hi, Please let me know if you have any ideas - I am taking wild guesses now.... Here is the situation: I put in Asterisk for a local customer. I have Fractional T-1 with 12 Voice & 12 Data. I have a T100P hooked up to a TDM Card (they call it a chanel bank although it only has 2 outputs) in a CAC unit. The unit also has a router card that runs the data side. My extensions are all SIP

> > >>SF framing is called d4 in the zaptel.conf. > > Thanks. > > Don't forget this will be ami and not b8zs. You have to use esf to > get > b8zs. This is not true. Line coding and framing are two different things and any type of line code can be used with any type of framing. - Line coding - AMI, B8ZS (there are others but I have forgotten them) - Framing -

Hi all I have a server that has two TE412P (T1/E1+DSP) cards installed. One of them configured as an E1 PRI connected to PSTN and another one configured as a T1 E&M connected to Avaya PBX. Each card only uses two ports, so there are 2 E1 lines and 2 T1 lines connecting to this server. The purpose of this server is as a TDM trunk gateway that gets call from E1/T1 and then forward to an IP-PBX

I'll keep asking weird questions here: I have two T1 WAN circuits originating at my asterisk box and terminating at Asterisk servers at remote sites. Currently I use zaptel ppp assigned to all 24 channels for data. Now I would like to split off a few of these channels for voice trunks (I should use VOIP, but at the moment I do not have fast enough servers for the codecs) At one site

In my * server I have a T100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm on the card starts blinking red. Running zttool confirmed that yes, it is a red alarm. I've read a few previous posts on this type of setup and I'm not too much closer. What should I be checking next? A different cable? The

I know this topic has been covered before - I just want to make sure I am understanding this correctly. | ------------------- | | | | T1 | Channel Bank | | ----------| | | | T1 Cross | | | | | | | | ------------------- -------------- | Asterisk | | | |